Wi-Fi / WLAN Channels, Frequencies, Bands & Bandwidths

- Wi-Fi / WLAN / 802.11 channels, their channel frequencies and bandwidth allocations around the globe, spectral mask and summary of which channels can be used together for WLAN solutions.

Wi-Fi IEEE 802.11 tutorials include:

    •   IEEE 802.11 standard tutorial
    •   IEEE 802.11a
    •   IEEE 802.11b
    •   IEEE 802.11e
    •   IEEE 802.11g
    •   IEEE 802.11i security & WEP / WPA
    •   IEEE 802.11n
    •   IEEE 802.11ac
    •   IEEE 802.11ad Microwave Wi-Fi
    •   IEEE 802.11af White-Fi
    •   802.11 Wi-Fi channels & frequencies

The IEEE 802.11 Wi-Fi / WLAN standards set the attributes for the different channels that may be used.

These attributes enable different Wi-Fi modules to talk to each other and effectively set up a WLAN.

To ensure that WLAN solutions operate satisfactorily, parameters such as the RF signal centre frequencies, channel numbers and the bandwidths must all be set..

ISM bands

Wi-Fi is aimed at use within unlicensed spectrum. This enables users to access the radio spectrum without the need for the regulations and restrictions that might be applicable elsewhere. The downside is that this spectrum is also shared by many other users and as a result the system has to be resilient to interference.

There are a number of unlicensed spectrum bands in a variety of areas of the radio spectrum. Often these are referred to as ISM bands - Industrial, Scientific and Medical, and they carry everything from microwave ovens to radio communications. Many of these bands, including he two used for Wi-Fi are global allocations, although local restrictions may apply for some aspects of their use.

The main bands used for carrying Wi-Fi are those in the table below:

Lower Frequency MHz	Upper Frequency MHz	Comments
2400	2500	Often referred to as the 2.4 GHz band, this spectrum is the most widely used of the bands available for Wi-Fi. Used by 802.11b, g, & n. It can carry a maximum of three non-overlapping channels.
5725	5875	This 5 GHz band or 5.8 GHz band provides additional bandwidth, and being at a higher frequency, equipment costs are slightly higher, although usage, and hence interference is less.It can be used by 802.11a & n. It can carry up to 23 non-overlapping channels, but gives a shorter range than 2.4 GHz.

2.4 GHz 802.11 channels

There is a total of fourteen channels defined for use by Wi-Fi 802.11 for the 2.4 GHz ISM band. Not all of the channels are allowed in all countries: 11 are allowed by the FCC and used in what is often termed the North American domain, and 13 are allowed in Europe where channels have been defined by ETSI. The WLAN / Wi-Fi channels are spaced 5 MHz apart (with the exception of a 12 MHz spacing between the last two channels).

The 802.11 WLAN standards specify a bandwidth of 22 MHz and a 25 MHz channel separation, although nominal figures for the bandwidth of 20 MHz are often given. The 20 / 22 MHz bandwidth and channel separation of 5 MHz means that adjacent channels overlap and signals on adjacent channels will interfere with each other.

The 22 MHz channel bandwidth holds for all standards even though 802.11b WLAN standard can run at variety of speeds: 1, 2, 5.5, or 11 Mbps and the newer 802.11g standard can run at speeds up to 54 Mbps. The differences occur in the RF modulation scheme used, but the WLAN channels are identical across all of the applicable 802.11 standards.

When using 802.11 Wi-Fi to provide WLAN solutions for offices, general use hotspots, or for any WLAN applications, it is necessary to ensure that parameters such as the channels are correctly set to ensure the required performance is achieved.

2.4 GHz Wi-Fi channel frequencies

The table given below provides the frequencies for the total of fourteen 802.11 Wi-Fi channels that are available around the globe. Not all of these channels are available for use in all countries.

Channel Number	Lower Frequency MHz	Center Frequency MHz	Upper Frequency MHz
1	2401	2412	2423
2	2404	2417	2428
3	2411	2422	2433
4	2416	2427	2438
5	2421	2432	2443
6	2426	2437	2448
7	2431	2442	2453
8	2436	2447	2458
9	2441	2452	2463
10	2451	2457	2468
11	2451	2462	2473
12	2456	2467	2478
13	2461	2472	2483
14	2473	2484	2495

2.4 GHz WiFi channel overlap and selection

The channels used for WiFi are separated by 5 MHz in most cases but have a bandwidth of 22 MHz. As a result channels overlap and it can be seen that it is possible to find a maximum of three non-overlapping channels. Therefore if there are adjacent pieces of WLAN equipment that need to work on non-interfering channels, there is only a possibility of three. There are five combinations of available non overlapping channels are given below:

Wi-Fi Channel overlap and which ones can be used as sets.

From the diagram above, it can be seen that Wi-Fi channels 1, 6, 11, or 2, 7, 12, or 3, 8, 13 or 4, 9, 14 (if allowed) or 5, 10 (and possibly 14 if allowed) can be used together as sets. Often WiFi routers are set to channel 6 as the default, and therefore the set of channels 1, 6 and 11 is possibly the most widely used.

As some energy spreads out further outside the nominal bandwidth, if only two channels are used, then the further away from each other the better the performance.

It is found that when interference exists, the throughput of the system is reduced. It therefore pays to reduce the levels of interference to improve the overall performance of the WLAN equipment.

With the use of IEEE 802.11n, there is the possibility of using signal bandwidths of either 20 MHz or 40 MHz. When 40 MHz bandwidth is used to gain the higher data throughput, this obviously reduces the number of channels that can be used.

802.11n 40 MHz channel capacity

The diagram above shows the 802.11n 40 MHz signals. These signals are designated with their equivalent centre channel numbers.

2.4 GHz WLAN / Wi-Fi Channel availability

In view of the differences in spectrum allocations around the globe and different requirements for the regulatory authorities, not all the WLAN channels are available in every country. The table below provides a broad indication of the availability of the different Wi-Fi channels in different parts of the world.

Channel Number	Europe (ETSI)	North America (FCC)	Japan
1	✔	✔	✔
2	✔	✔	✔
3	✔	✔	✔
4	✔	✔	✔
5	✔	✔	✔
6	✔	✔	✔
7	✔	✔	✔
8	✔	✔	✔
9	✔	✔	✔
10	✔	✔	✔
11	✔	✔	✔
12	✔	No	✔
13	✔	No	✔
14	No	No	802.11b only

This chart is only provides a general view, and there may be variations between different countries. For example some countries within the European zone Spain have restrictions on the channels that may be used (France: channels 10 - 13 and Spain channels 10 and 11) use of Wi-Fi and do not allow many of the channels that might be thought to be available, although the position is likely to change.

3.6 GHz WiFi band

This band of frequencies is only allowed for use within the USA under a scheme known as 802.11y. Here high powered stations can be used as backhaul for networks, etc.

Channel Number	Frequency (MHz)	5 MHz Bandwidth	10 MHz Bandwidth	20 MHz Bandwidth
131	3657.5	✔
132	36622.5	✔
132	3660.0		✔
133	3667.5	✔
133	3665.0			✔
134	3672.5	✔
134	3670.0		✔
135	3677.5	✔
136	3682.5	✔
136	3680.0		✔
137	3687.5	✔
137	3685.0			✔
138	3689.5	✔
138	3690.0		✔

Note: the channel centre frequency depends upon the bandwidth used. This accounts for the fact that the centre frequency for various channels is different if different signal bandwidths are used.

5 GHz WiFi channels & frequencies

As the 2.4 GHz band becomes more crowded, many users are opting to use the 5 GHz ISM band. This not only provides more spectrum, but it is not as widely used by Wi-Fi as well as many other appliances including items such as microwave ovens, etc.

It will be seen that many of the 5 GHz Wi-Fi channels fall outside the accepted ISM unlicensed band and as a result various restrictions are placed on operation at these frequencies.

Channel Number	Frequency MHz	Europe (ETSI)	North America (FCC)	Japan
36	5180	Indoors	✔	✔
40	5200	Indoors	✔	✔
44	5220	Indoors	✔	✔
48	5240	Indoors	✔	✔
52	5260	Indoors / DFS / TPC	DFS	DFS / TPC
56	5280	Indoors / DFS / TPC	DFS	DFS / TPC
60	5300	Indoors / DFS / TPC	DFS	DFS / TPC
64	5320	Indoors / DFS / TPC	DFS	DFS / TPC
100	5500	DFS / TPC	DFS	DFS / TPC
104	5520	DFS / TPC	DFS	DFS / TPC
108	5540	DFS / TPC	DFS	DFS / TPC
112	5560	DFS / TPC	DFS	DFS / TPC
116	5580	DFS / TPC	DFS	DFS / TPC
120	5600	DFS / TPC	No Access	DFS / TPC
124	5620	DFS / TPC	No Access	DFS / TPC
128	5640	DFS / TPC	No Access	DFS / TPC
132	5660	DFS / TPC	DFS	DFS / TPC
136	5680	DFS / TPC	DFS	DFS / TPC
140	5700	DFS / TPC	DFS	DFS / TPC
149	5745	SRD	✔	No Access
153	5765	SRD	✔	No Access
157	5785	SRD	✔	No Access
161	5805	SRD	✔	No Access
165	5825	SRD	✔	No Access

Note 1: there are additional regional variations for countries including Australia, Brazil, China, Israel, Korea, Singapore, South Africa, Turkey, etc. Additionally Japan has access to some channels below 5180 MHz.

Note 2: DFS = Dynamic Frequency Selection; TPC = Transmit Power Control; SRD = Short Range Devices 25 mW max power.

Additional bands and frequencies

In addition to the more established forms of Wi-Fi, new formats are being developed that will use new frequencies and bands. Technologies employing white space usage, etc. and also new standards using bands that are well into the microwave region and will deliver gigabit transfer speeds are being developed and introduced. These technologies will require the use of new spectrum for Wi-Fi.

Wi-Fi Technology	Standard	Frequencies Bands
White-Fi	802.11af	470 - 710MHz
Microwave Wi-Fi	802.11ad	57.0 - 64.0 GHz ISM band (Regional variations apply) Channels: 58,32, 60.48, 62.64, and 64.80 GHz

As WLAN and Wi-Fi technology develops further new bands will be added to enable sufficient interference bandwidth to be available to ensure the ever increasing requirement for the transfer of high speed data.

By Ian Poolehttp://www.radio-electronics.com/info/wireless/wi-fi/80211-channels-number-frequencies-bandwidth.php