BUS HOUND调试USB驱动遇到的错误代码解析

在使用BUS HOUND调试USB驱动时，在Capture页面会遇到抓取的错误信息，错误代码会在data字段显示，根据不同的显示，含义如下：

顺便记录用于以后代码分析。

Value	Code	Meaning
USBD_STATUS_CRC	0xC0000001	CRC error (defined for backward compatibility with the USB 1.0).
USBD_STATUS_BTSTUFF	0xC0000002	BTS error (defined for backward compatibility with the USB 1.0).
USBD_STATUS_DATA_TOGGLE_MISMATCH	0xC0000003	Data toggle mismatch.
USBD_STATUS_STALL_PID	0xC0000004	The device returned a stall packet identifier (defined for backward compatibility with the USB 1.0)
USBD_STATUS_DEV_NOT_RESPONDING	0xC0000005	The device is not responding (defined for backward compatibility with the USB 1.0).
USBD_STATUS_PID_CHECK_FAILURE	0xC0000006	The device returned a packet identifier check failure (defined for backward compatibility with the USB 1.0).
USBD_STATUS_UNEXPECTED_PID	0xC0000007	The device returned an unexpected packet identifier error (defined for backward compatibility with the USB 1.0).
USBD_STATUS_DATA_OVERRUN	0xC0000008	The device returned a data overrun error (defined for backward compatibility with the USB 1.0).
USBD_STATUS_DATA_UNDERRUN	0xC0000009	The device returned a data underrun error (defined for backward compatibility with the USB 1.0).
USBD_STATUS_RESERVED1	0xC000000A	Reserved.
USBD_STATUS_RESERVED2	0xC000000B	Reserved.
USBD_STATUS_BUFFER_OVERRUN	0xC000000C	The device returned a buffer overrun error (defined for backward compatibility with the USB 1.0).
USBD_STATUS_BUFFER_UNDERRUN	0xC000000D	The device returned a buffer underrun error (defined for backward compatibility with the USB 1.0).
USBD_STATUS_NOT_ACCESSED	0xC000000F	The USB stack could not access the device (defined for backward compatibility with the USB 1.0).
USBD_STATUS_FIFO	0xC0000010	The device returned a FIFO error (defined for backward compatibility with the USB 1.0).
USBD_STATUS_XACT_ERROR	0xC0000011	The device returned a transaction error (defined for backward compatibility with the USB 1.0).
USBD_STATUS_BABBLE_DETECTED	0xC0000012	The device returned a babble detected error (defined for backward compatibility with the USB 1.0).
USBD_STATUS_DATA_BUFFER_ERROR	0xC0000013	Hardware status codes that range from 0x00000001 to 0x000000FF (defined for backward compatibility with the USB 1.0 stack).
USBD_STATUS_NO_PING_RESPONSE	0xC0000014	No response was received from the device for a ping packet sent by the host.
USBD_STATUS_INVALID_STREAM_TYPE	0xC0000015	The stream type is invalid for the endpoint.
USBD_STATUS_INVALID_STREAM_ID	0xC0000016	The stream identifier is invalid.
USBD_STATUS_ENDPOINT_HALTED	0xC0000030	A transfer was submitted to an endpoint that is stalled.
USBD_STATUS_INVALID_URB_FUNCTION	0x80000200	Invalid URB function.
USBD_STATUS_INVALID_PARAMETER	0x80000300	Invalid parameter.
USBD_STATUS_ERROR_BUSY	0x80000400	The client driver caused an error by attempting to close an endpoint, interface, or configuration handle with outstanding transfers.
USBD_STATUS_REQUEST_FAILED	0x80000500	The hub driver cannot complete a URB request.
USBD_STATUS_INVALID_PIPE_HANDLE	0x80000600	Invalid pipe handle.
USBD_STATUS_NO_BANDWIDTH	0x80000700	There was not enough bandwidth to open a requested endpoint.
USBD_STATUS_INTERNAL_HC_ERROR	0x80000900	Unspecified host controller error.
USBD_STATUS_ERROR_SHORT_TRANSFER	0x80000900	The transfer ended with a short packet, but the USBD_SHORT_TRANSFER_OK bit is not set for the pipe.
USBD_STATUS_BAD_START_FRAME	0xC0000A00	The requested start frame is not within a range of USBD_ISO_START_FRAME_RANGE frames of the current USB frame. Whenever this error occurs, the system sets the stall bit on the pipe.
USBD_STATUS_ISOCH_REQUEST_FAILED	0xC0000B00	The host controller returns this error whenever all packets in an isochronous transfer complete with an error.
USBD_STATUS_FRAME_CONTROL_OWNED	0xC0000C00	The hub driver returns this error whenever the frame length control for the host controller is being used by a driver other than the host controller driver.
USBD_STATUS_FRAME_CONTROL_NOT_OWNED	0xC0000D00	The hub driver returns this error if the caller does not own frame length control and attempts to release or modify the host controller frame length.
USBD_STATUS_NOT_SUPPORTED	0xC0000E00	The request was not supported.
USBD_STATUS_INAVLID_CONFIGURATION_DESCRIPTOR	0xC0000F00	Invalid configuration descriptor.
USBD_STATUS_INSUFFICIENT_RESOURCES	0xC0001000	Insufficient resources.
USBD_STATUS_SET_CONFIG_FAILED	0xC0002000	An attempt to change the device configuration failed.
USBD_STATUS_BUFFER_TOO_SMALL	0xC0003000	The buffer is too small.
USBD_STATUS_INTERFACE_NOT_FOUND	0xC0004000	The interface was not found.
USBD_STATUS_INAVLID_PIPE_FLAGS	0xC0005000	Invalid pipe flags.
USBD_STATUS_TIMEOUT	0xC0006000	The request timed out.
USBD_STATUS_DEVICE_GONE	0xC0007000	The device is no longer present in the system.
USBD_STATUS_STATUS_NOT_MAPPED	0xC0008000	The device bus address is not mapped to system memory.
USBD_STATUS_HUB_INTERNAL_ERROR	0xC0009000	The hub driver returns this error whenever it intercepted a URB that was targeted at some other device.
USBD_STATUS_CANCELED	0xC0010000	The USB stack reports this error whenever it completed a transfer because of an AbortPipe request from the client driver.
USBD_STATUS_ISO_NOT_ACCESSED_BY_HW	0xC0020000	The host controller did not access the transfer descriptor (TD) that is associated with this packet. The USB stack reports this error in the packet status field of an isochronous transfer packet.
USBD_STATUS_ISO_TD_ERROR	0xC0030000	The host controller reported an error in the transfer descriptor (TD). The USB stack reports this error in the packet status field of an isochronous transfer packet.
USBD_STATUS_ISO_NA_LATE_USBPORT	0xC0040000	The client driver submitted the packet on time, but the packet failed to reach the miniport driver on time. The USB stack reports this error in the packet status field of an isochronous transfer packet.
USBD_STATUS_ISO_NOT_ACCESSED_LATE	0xC0050000	The client driver did not submit the packet on time. The USB stack reports this error in the packet status field of an isochronous transfer packet.
USBD_STATUS_BAD_DESCRIPTOR	0xC0100000	Invalid descriptor.
USBD_STATUS_BAD_DESCRIPTOR_BLEN	0xC0100001	Invalid descriptor length.
USBD_STATUS_BAD_DESCRIPTOR_TYPE	0xC0100002	Invalid descriptor type.
USBD_STATUS_BAD_INTERFACE_DESCRIPTOR	0xC0100003	Invalid interface descriptor.
USBD_STATUS_BAD_ENDPOINT_DESCRIPTOR	0xC0100004	Invalid endpoint descriptor.
USBD_STATUS_BAD_INTERFACE_ASSOC_DESCRIPTOR	0xC0100005	Invalid interface association descriptor.
USBD_STATUS_BAD_CONFIG_DESC_LENGTH	0xC0100006	Invalid configuration descriptor length.
USBD_STATUS_BAD_NUMBER_OF_INTERFACES	0xC0100007	Invalid number of interfaces.
USBD_STATUS_BAD_NUMBER_OF_ENDPOINTS	0xC0100008	Invalid number of endpoints.
USBD_STATUS_BAD_ENDPOINT_ADDRESS	0xC0100009	Invalid endpoint address.