20240816使用SDDiskTool_v1.69写32GB的TF卡后给飞凌OK3588-C核心板刷机异常了

20240816使用SDDiskTool_v1.69写32GB的TF卡后给飞凌OK3588-C核心板刷机异常了
2024/8/16 20:41

参考资料：《OK3588-C_Linux5.10.66+Qt5.15.2_用户使用手册_V1.2_20240321.pdf》的 《4.2 TF 卡烧写系统》
由于 E:\20240506的OK3588-C开发板\OK3588-C_Linux5.10.66+Qt5.15.2_用户资料_R4(更新日期_20240321)\Linux\工具\SDDiskTool_v1.72.zip
搜索了一下，找到了一个SDDiskTool_v1.69.zip。

心跳灯是什么状态
烧写的时候不在串口输入命令，等着就行

?等了十分钟+，串口没有提示。HDMI显示器没有显示/黑屏
一直红灯 蓝灯 常亮 超过10分钟了

流程：
1.将卡插入板卡
2.上电启动，修改显示接口
3.按0，按1重新启动

据飞凌：由于通过TF卡刷机也就是先要通过TF卡启动，那就是把TF卡的默认/主显示屏也要配置为HDMI0。

一番操作之后，发现卡死在 reboot system now 这个地方。
现在这么搞，就算你等一天也不会刷机的。如果是开发板，有按键，可以进入下一个选项：
apply update from sdcard

既然现在有最新的 SDDiskTool_v1.72.zip了。更换写卡工具试试了！

TF卡升级的问题：
1、不同系统升级 Ubuntu/Deiban/Android12可以通过卡刷为Buildroot/Linux不？
2、不同大小分区表可以通过TF卡升级不？32GB的分区表/64GB的分区表？
3、白片/白卡/空的EMMC可以卡刷不？

飞凌：
可以的。
可以的。
可以的。

飞凌提供的正常的刷机画面：

甚至把我的IMG固件通过E-MAIL发给了飞凌，可以用的！

甚至比对了生成的TF卡中的IMG和原始的IMG的MD5值，一样的！

b7b0f81989592f48ba2af8f50cf871df

[BEGIN] 2024/8/16 20:38:26
root@RK3588:/# DDR Version V1.07 20220412
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-g5f53abfa1e-221223 #zzz (Dec 26 2022 - 09:10:09)
unknown raw ID 0 0 0
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(5ae6932916...) + OK
## Checking uboot 0x00200000 ... sha256(5ca6150e38...) + OK
## Checking fdt 0x00325ad0 ... sha256(6c1121228f...) + OK
## Checking atf-2 0x000f0000 ... sha256(c00c7fd75b...) + OK
## Checking atf-3 0xff100000 ... sha256(71c3a5841b...) + OK
## Checking atf-4 0xff001000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(4ed9cd20b5...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 325.395 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-384-g45c8fcb44:derrick.huang
NOTICE:  BL31: Built : 15:14:04, Jun 18 2022
INFO:    ext 32k is not valid
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
INFO:    hdmirx_handler: dma not on, ret
I/TC: 
I/TC: OP-TEE version: 3.13.0-645-g87d94c5ef8 #xb.wang (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #1 Tue Jun 14 10:44:31 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9

U-Boot 2017.09 (Dec 21 2023 - 09:45:34 +0800)

Model: Forlinx OK3588-C Board
PreSerial: 2, raw, 0xfeb50000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: edb51000
Relocation fdt: eb9fa7a8 - eb9fecd8
CR: M/C/I
no mmc device at slot 1
mmc@fe2c0000: 1 (SD), mmc@fe2e0000: 0
Bootdev(atags): mmc 1
MMC1: Legacy, 52Mhz
PartType: EFI
DM: v2
boot mode: recovery (misc)
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 800000 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 800000 uV
I2c1 speed: 400000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 800000 uV
spi2: RK806: 2
ON=0x00, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
Device 'gpio@fd8a0000': seq 0 is in use by 'gpio@fd8a0000'
Device 'gpio@fec20000': seq 1 is in use by 'gpio@fd8a0000'
Device 'gpio@fec40000': seq 3 is in use by 'gpio@fec20000'
Auth Success!
normal mode
Writing to mmc(1)... done
get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts
get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts
get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts
get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts
Device 'gpio@fec50000': seq 4 is in use by 'gpio@fec40000'
bank id invalid
Cannot get enable GPIO: -22
Warn: can't find connect driver
Could not find baseparameter partition
Model: Forlinx OK3588 Board
Rockchip UBOOT DRM driver version: v1.0.1
vp0 have layer nr:2[0 2 ], primary plane: 2
vp1 have layer nr:2[1 3 ], primary plane: 3
vp2 have layer nr:2[6 8 ], primary plane: 8
vp3 have layer nr:2[7 9 ], primary plane: 9
Using display timing dts
dsi@fde20000:  detailed mode clock 45000 kHz, flags[a]
    H: 1024 1064 1112 1160
    V: 0600 0640 0644 0692
bus_format: 100e
VOP update mode to: 1024x600p0, type: MIPI0 for VP2
rockchip_vop2_init:No hdmiphypll clk0 found, use system clk
rockchip_vop2_init:No hdmiphypll clk1 found, use system clk
VOP VP2 enable Esmart2[400x300->400x300@312x150] fmt[1] addr[0xedf58000]
final DSI-Link bandwidth: 293333 Kbps x 4
Using display timing dts
dsi@fde30000:  detailed mode clock 45000 kHz, flags[a]
    H: 1024 1064 1112 1160
    V: 0600 0640 0644 0692
bus_format: 100e
VOP update mode to: 1024x600p0, type: MIPI1 for VP3
rockchip_vop2_init:No hdmiphypll clk0 found, use system clk
rockchip_vop2_init:No hdmiphypll clk1 found, use system clk
VOP VP3 enable Esmart3[400x300->400x300@312x150] fmt[1] addr[0xedf58000]
final DSI-Link bandwidth: 294113 Kbps x 4
dp@fde60000 disconnected
CLK: (uboot. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
  b0pll 24000 KHz
  b1pll 24000 KHz
  lpll 24000 KHz
  v0pll 24000 KHz
  aupll 786215 KHz
  cpll 1500000 KHz
  gpll 1188000 KHz
  npll 850000 KHz
  ppll 1100000 KHz
  aclk_center_root 702000 KHz
  pclk_center_root 100000 KHz
  hclk_center_root 396000 KHz
  aclk_center_low_root 500000 KHz
  aclk_top_root 750000 KHz
  pclk_top_root 100000 KHz
  aclk_low_top_root 396000 KHz
Net:   eth1: ethernet@fe1c0000
Hit key to stop autoboot('Spacebar'):  0 
---------------------------------------------
0:Exit to console
1:Reboot
2:Display type
---------------------------------------------
Writing to mmc(1)... done
Writing to mmc(1)... done
---------------------------------------------
hdmi0 and edp0 share same port, only one can be used.
hdmi1 and edp1 share same port, only one can be used.
only four VPs internally, so up to four interfaces can be activated
hdmi edp dp can only be displayed on VP0 or VP1 or VP2.
dsi0 dsi1 can only be displayed on VP2 or  VP3.
rgb can only be displayed on VP3.

Select  display
  0:Exit
  1: hdmi0 => VP0
  2: hdmi1 => 
  3: edp0  => 
  4: edp1  => 
  5: dp0   => 
  6: dp1   => VP1
  7: mipi0 => VP2
  8: mipi1 => VP3
  9: rgb   => 
  a: primary display  => MIPI0
  b: primary display resolution => 1920x1080p60
  c: display type => sync
---------------------------------------------
display forced by kernel dtb
Writing to mmc(1)... done
Writing to mmc(1)... done
Writing to mmc(1)... done
---------------------------------------------
hdmi0 and edp0 share same port, only one can be used.
hdmi1 and edp1 share same port, only one can be used.
only four VPs internally, so up to four interfaces can be activated
hdmi edp dp can only be displayed on VP0 or VP1 or VP2.
dsi0 dsi1 can only be displayed on VP2 or  VP3.
rgb can only be displayed on VP3.

Select  display
  0:Exit
  1: hdmi0 => VP0
  2: hdmi1 => 
  3: edp0  => 
  4: edp1  => 
  5: dp0   => 
  6: dp1   => VP1
  7: mipi0 => VP2
  8: mipi1 => VP3
  9: rgb   => 
  a: primary display  => MIPI1
  b: primary display resolution => 1920x1080p60
  c: display type => sync
---------------------------------------------
display forced by kernel dtb
Writing to mmc(1)... done
Writing to mmc(1)... done
Writing to mmc(1)... done
---------------------------------------------
hdmi0 and edp0 share same port, only one can be used.
hdmi1 and edp1 share same port, only one can be used.
only four VPs internally, so up to four interfaces can be activated
hdmi edp dp can only be displayed on VP0 or VP1 or VP2.
dsi0 dsi1 can only be displayed on VP2 or  VP3.
rgb can only be displayed on VP3.

Select  display
  0:Exit
  1: hdmi0 => VP0
  2: hdmi1 => 
  3: edp0  => 
  4: edp1  => 
  5: dp0   => 
  6: dp1   => VP1
  7: mipi0 => VP2
  8: mipi1 => VP3
  9: rgb   => 
  a: primary display  => HDMI0
  b: primary display resolution => 1920x1080p60
  c: display type => sync
---------------------------------------------
display forced by kernel dtb
Writing to mmc(1)... done
Writing to mmc(1)... done
Writing to mmc(1)... done
---------------------------------------------
hdmi0 and edp0 share same port, only one can be used.
hdmi1 and edp1 share same port, only one can be used.
only four VPs internally, so up to four interfaces can be activated
hdmi edp dp can only be displayed on VP0 or VP1 or VP2.
dsi0 dsi1 can only be displayed on VP2 or  VP3.
rgb can only be displayed on VP3.

Select  display
  0:Exit
  1: hdmi0 => VP0
  2: hdmi1 => 
  3: edp0  => 
  4: edp1  => 
  5: dp0   => 
  6: dp1   => VP2
  7: mipi0 => 
  8: mipi1 => VP3
  9: rgb   => 
  a: primary display  => HDMI0
  b: primary display resolution => 1920x1080p60
  c: display type => sync
---------------------------------------------
display forced by kernel dtb
Writing to mmc(1)... done
Writing to mmc(1)... done
Writing to mmc(1)... done
---------------------------------------------
hdmi0 and edp0 share same port, only one can be used.
hdmi1 and edp1 share same port, only one can be used.
only four VPs internally, so up to four interfaces can be activated
hdmi edp dp can only be displayed on VP0 or VP1 or VP2.
dsi0 dsi1 can only be displayed on VP2 or  VP3.
rgb can only be displayed on VP3.

Select  display
  0:Exit
  1: hdmi0 => VP0
  2: hdmi1 => 
  3: edp0  => 
  4: edp1  => 
  5: dp0   => 
  6: dp1   => 
  7: mipi0 => 
  8: mipi1 => VP3
  9: rgb   => 
  a: primary display  => HDMI0
  b: primary display resolution => 1920x1080p60
  c: display type => sync
---------------------------------------------
display forced by kernel dtb
Writing to mmc(1)... done
Writing to mmc(1)... done
Writing to mmc(1)... done
---------------------------------------------
hdmi0 and edp0 share same port, only one can be used.
hdmi1 and edp1 share same port, only one can be used.
only four VPs internally, so up to four interfaces can be activated
hdmi edp dp can only be displayed on VP0 or VP1 or VP2.
dsi0 dsi1 can only be displayed on VP2 or  VP3.
rgb can only be displayed on VP3.

Select  display
  0:Exit
  1: hdmi0 => VP0
  2: hdmi1 => 
  3: edp0  => 
  4: edp1  => 
  5: dp0   => 
  6: dp1   => 
  7: mipi0 => 
  8: mipi1 => 
  9: rgb   => 
  a: primary display  => HDMI0
  b: primary display resolution => 1920x1080p60
  c: display type => sync
---------------------------------------------
---------------------------------------------
0:Exit to console
1:Reboot
2:Display type
---------------------------------------------
DDR Version V1.07 20220412
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-g5f53abfa1e-221223 #zzz (Dec 26 2022 - 09:10:09)
unknown raw ID 0 0 0
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(5ae6932916...) + OK
## Checking uboot 0x00200000 ... sha256(5ca6150e38...) + OK
## Checking fdt 0x00325ad0 ... sha256(6c1121228f...) + OK
## Checking atf-2 0x000f0000 ... sha256(c00c7fd75b...) + OK
## Checking atf-3 0xff100000 ... sha256(71c3a5841b...) + OK
## Checking atf-4 0xff001000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(4ed9cd20b5...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 313.955 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-384-g45c8fcb44:derrick.huang
NOTICE:  BL31: Built : 15:14:04, Jun 18 2022
INFO:    ext 32k is not valid
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
INFO:    hdmirx_handler: dma not on, ret
I/TC: 
I/TC: OP-TEE version: 3.13.0-645-g87d94c5ef8 #xb.wang (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #1 Tue Jun 14 10:44:31 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9

U-Boot 2017.09 (Dec 21 2023 - 09:45:34 +0800)

Model: Forlinx OK3588-C Board
PreSerial: 2, raw, 0xfeb50000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: edb51000
Relocation fdt: eb9fa7a8 - eb9fecd8
CR: M/C/I
no mmc device at slot 1
mmc@fe2c0000: 1 (SD), mmc@fe2e0000: 0
Bootdev(atags): mmc 1
MMC1: Legacy, 52Mhz
PartType: EFI
DM: v2
boot mode: recovery (misc)
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 800000 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 800000 uV
I2c1 speed: 400000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 800000 uV
spi2: RK806: 2
ON=0x00, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
Device 'gpio@fd8a0000': seq 0 is in use by 'gpio@fd8a0000'
Device 'gpio@fec20000': seq 1 is in use by 'gpio@fd8a0000'
Device 'gpio@fec40000': seq 3 is in use by 'gpio@fec20000'
Auth Success!
normal mode
Writing to mmc(1)... done
Device 'gpio@fec50000': seq 4 is in use by 'gpio@fec40000'
bank id invalid
Cannot get enable GPIO: -22
Warn: can't find connect driver
Writing to mmc(1)... done
Device 'gpio@fec50000': seq 4 is in use by 'gpio@fec40000'
bank id invalid
Cannot get enable GPIO: -22
Warn: can't find connect driver
Model: Forlinx OK3588 Board
CLK: (uboot. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
  b0pll 24000 KHz
  b1pll 24000 KHz
  lpll 24000 KHz
  v0pll 24000 KHz
  aupll 786215 KHz
  cpll 1500000 KHz
  gpll 1188000 KHz
  npll 850000 KHz
  ppll 1100000 KHz
  aclk_center_root 702000 KHz
  pclk_center_root 100000 KHz
  hclk_center_root 396000 KHz
  aclk_center_low_root 500000 KHz
  aclk_top_root 750000 KHz
  pclk_top_root 100000 KHz
  aclk_low_top_root 396000 KHz
Net:   eth1: ethernet@fe1c0000
Hit key to stop autoboot('Spacebar'):  0 
ANDROID: reboot reason: "recovery"
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xe739c380 with size 0x0445d400
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e739c380 ...
   Using 'conf' configuration
optee api revision: 2.0
TEEC: Waring: Could not find security partition
## Verified-boot: 0
   Trying 'kernel' kernel subimage
     Description:  unavailable
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0xe73c7f80
     Data Size:    33509888 Bytes = 32 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x00400000
     Entry Point:  0x00400000
     Hash algo:    sha256
     Hash value:   e549e7e58056e5682b1325a136a33bdb79297107bfd1442094db6c8e3c427f88
   Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at e739c380 ...
   Using 'conf' configuration
   Trying 'ramdisk' ramdisk subimage
     Description:  unavailable
     Type:         RAMDisk Image
     Compression:  uncompressed
     Data Start:   0xe93bd180
     Data Size:    37995896 Bytes = 36.2 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x0a200000
     Entry Point:  unavailable
     Hash algo:    sha256
     Hash value:   5e769560034c269834f4c008182a15b25b904f609b2d203ed6fece545f528ad5
   Verifying Hash Integrity ... sha256+ OK
   Loading ramdisk from 0xe93bd180 to 0x0a200000
## Loading fdt from FIT Image at e739c380 ...
   Using 'conf' configuration
   Trying 'fdt' fdt subimage
     Description:  unavailable
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0xe739cb80
     Data Size:    177129 Bytes = 173 KiB
     Architecture: AArch64
     Load Address: 0x0a100000
     Hash algo:    sha256
     Hash value:   bcc12344b5d026176fde2ae6df28cbb654d5fd93a433443185ce53e926e181f4
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x0a100000 to 0x0a100000
   Booting using the fdt blob at 0x0a100000
   Loading Kernel Image from 0xe73c7f80 to 0x00400000 ... OK
   kernel loaded at 0x00400000, end = 0x023f5200
  'reserved-memory' dma-trans@3c000000: addr=3c000000 size=4000000
  'reserved-memory' cma: addr=10000000 size=10000000
   Using Device Tree in place at 000000000a100000, end 000000000a12e3e8
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 7448.741 ms

Starting kernel ...

I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
mount: mounting /dev/mmcblk1p1 on /mnt/sdcard failed: No such file or directory
mount: mounting PARTLABEL=oem on /oem failed: No such file or directory
mount: mounting PARTLABEL=userdata on /userdata failed: No such file or directory
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Populating /dev using udev: done
Saving random seed: OK
Starting network: OK
Debug: configfs_init
mkdir: cannot create directory '/sys/kernel/config/usb_gadget/rockchip/functions/uac1.gs0': No such file or directory
mkdir: cannot create directory '/sys/kernel/config/usb_gadget/rockchip/functions/uac2.gs0': No such file or directory
mkdir: cannot create directory '/sys/kernel/config/usb_gadget/rockchip/functions/mtp.gs0': No such file or directory
mkdir: cannot create directory '/sys/kernel/config/usb_gadget/rockchip/functions/rndis.gs0': No such file or directory
mkdir: cannot create directory '/sys/kernel/config/usb_gadget/rockchip/functions/acm.gs6': No such file or directory
mkdir: cannot create directory '/sys/kernel/config/usb_gadget/rockchip/functions/hid.usb0': No such file or directory
Starting input-event-daemon: input-event-daemon: Start parsing /etc/input-event-daemon.conf...
input-event-daemon: Adding device: /dev/input/event0...
input-event-daemon: Adding device: /dev/input/event1...
input-event-daemon: Adding device: /dev/input/event2...
input-event-daemon: Start listening on 3 devices...
done
root@RK3588:/# 
root@RK3588:/# 
root@RK3588:/# 
root@RK3588:/# 
root@RK3588:/# 

[END] 2024/8/16 20:40:04