c语言stm32按下按键灯常量,stm32 检测到按键按上 灯亮 否则灯不亮

stm32 检测到按键按下 灯亮 否则灯不亮

/****************************************************************************

* File Name          : key_led.c.c

* Author               : MCD Application Team

* FW Version        : V2.0.1

* Date                  : 06/11/2012

* Description        : This file provides all the RCC firmware functions.

*开发板                  ：神舟三号

* 现象                    ：如程序执行前按住按键USER2 LED亮起，没按则灯不亮

*****************************************************************************

*/

#include "stm32f10x_lib.h"

/   define LED   ///

#define  RCC_GPIO_LED               RCC_APB2Periph_GPIOF

#define  GPIO_LED                     GPIOF

#define  GPIO_LED_PIN         GPIO_Pin_6

/   define KEY   ///

#define  RCC_GPIO_KEY       RCC_APB2Periph_GPIOD

#define  GPIO_KEY      GPIOD

#define  GPIO_KEY_PIN                    GPIO_Pin_3

/   define Beep  ///

#define  RCC_GPIO_BEEP                RCC_APB2Periph_GPIOB

#define  GPIO_BEEP                    GPIOB

#define  GPIO_BEEP_PIN                GPIO_Pin_10

/   config LED   ///

void LED_Config(void)

{

GPIO_InitTypeDef GPIO_InitStructure;

// RCC_ABP2PeriphClockCmd(RCC_GPIO_LED,ENABLE);

GPIO_InitStructure.GPIO_Pin =  GPIO_LED_PIN;

GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;

// GPIO_SetBits(GPIO_LED,GPIO_LED_PIN); //初始化完成才能使用输出功能

GPIO_Init(GPIO_LED, &GPIO_InitStructure);

GPIO_SetBits(GPIO_LED,GPIO_LED_PIN);

}

void LED_Turn_on(void)

{

GPIO_ResetBits(GPIO_LED,GPIO_LED_PIN);

}

void LED_Turn_off(void)

{

GPIO_SetBits(GPIO_LED,GPIO_LED_PIN);

}

/   config KEY   ///

void KEY_Config(void)

{

GPIO_InitTypeDef GPIO_InitStructure;

// RCC_ABP2PeriphClockCmd(RCC_GPIO_KEY,ENABLE);

GPIO_InitStructure.GPIO_Pin =  GPIO_KEY_PIN;

GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;//需要配置速率

GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;

GPIO_Init(GPIO_KEY, &GPIO_InitStructure);

}

int Is_KeyDown(void)

{

if( !GPIO_ReadInputDataBit(GPIO_KEY,GPIO_KEY_PIN) )

{

return  1 ;

}

else

return 0  ;

}

/// RccConfig///

void RccConfiguration(void)

{

ErrorStatus HSEStartUpStatus;

/* RCC system reset(for debug purpose) */

RCC_DeInit();

/* Enable HSE */

RCC_HSEConfig(RCC_HSE_ON);     //启动外部晶体震荡器

/* Wait till HSE is ready */

HSEStartUpStatus = RCC_WaitForHSEStartUp(); //等待启动完成

if(HSEStartUpStatus == SUCCESS)   //如果启动成功，继续配置系统频率

{

/* Enable Prefetch Buffer */

FLASH_PrefetchBufferCmd(FLASH_PrefetchBuffer_Enable);//选择flash预取址缓存模式

/* Flash 2 wait state */

FLASH_SetLatency(FLASH_Latency_2); //设置flash存储器延时时钟周期数

/* HCLK = SYSCLK */

RCC_HCLKConfig(RCC_SYSCLK_Div1);  //设置HCLK相对SYSCLK的分频比例  AHB时钟

/* PCLK2 = HCLK */

RCC_PCLK2Config(RCC_HCLK_Div1);   //设置PCLK2相对SYSCLK的分频比例  设置高速AHB时钟

/* PCLK1 = HCLK/2 */

RCC_PCLK1Config(RCC_HCLK_Div2);

/* PLLCLK = 8MHz * 9 = 72 MHz */

RCC_PLLConfig(RCC_PLLSource_HSE_Div1, RCC_PLLMul_9);

/* Enable PLL */

RCC_PLLCmd(ENABLE);//启动PLL

/* Wait till PLL is ready */

while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET)

{

}

/* Select PLL as system clock source */

RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);

/* Wait till PLL is used as system clock source */

while(RCC_GetSYSCLKSource() != 0x08)

{

}

}

RCC_APB2PeriphClockCmd(RCC_GPIO_LED,ENABLE);

RCC_APB2PeriphClockCmd(RCC_GPIO_KEY,ENABLE);

RCC_APB2PeriphClockCmd(RCC_GPIO_BEEP,ENABLE);

}

NvicConfig//

void NvicConfiguration(void)

{

NVIC_InitTypeDef NVIC_InitStructure;

#ifdef  VECT_TAB_RAM

/* Set the Vector Table base location at 0x20000000 */

NVIC_SetVectorTable(NVIC_VectTab_RAM, 0x0);

#else  /* VECT_TAB_FLASH  */

/* Set the Vector Table base location at 0x08000000 */

NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x0);

#endif

}

void ConfigureInterfaces(void)

{

/* System Clocks Configuration */

RccConfiguration();          //配置系统时钟

/* NVIC configuration */

NvicConfiguration();   //设置向量入口

}

int main(void)

{

ConfigureInterfaces();

LED_Config();

KEY_Config();

while(1)

{

if(Is_KeyDown()==1)

{

LED_Turn_on();

}

else

{

LED_Turn_off();

}

}

}