zynq linux千兆网卡驱动,zynq linux ar8031驱动 使得支持千兆网

使用相同的环境，目前稍好点，mii info能看到东西了：

U-Boot 2018.01 (Jun 04 2020 - 02:02:40 +0000) Xilinx ZynqMP ZCU102 rev1.0

I2C: ready

DRAM: 2 GiB

EL Level:EL2

Chip ID:zu2eg

MMC: mmc@ff160000: 0 (eMMC), mmc@ff170000: 1 (SD)

** Unable to use mmc 0:0 for loading the env **

Using default environment

In: serial@ff000000

Out: serial@ff000000

Err: serial@ff000000

Board: Xilinx ZynqMP

Bootmode: SD_MODE1

Net: ZYNQ GEM: ff0d0000, phyaddr 0, interface sgmii

eth0: ethernet@ff0d0000

U-BOOT for hb_demo_2018

ethernet@ff0d0000: No link.

Hit any key to stop autoboot: 0

ZynqMP>

ZynqMP> mii info

PHY 0x03: OUI = 0x3FFFC0, Model = 0x00, Rev = 0x00, 100baseX, FDX

ZynqMP> mii info

PHY 0x01: OUI = 0x3FFFC0, Model = 0x00, Rev = 0x00, 1000baseX, FDX

ZynqMP> mii info

ZynqMP> mii info

ZynqMP> mii info

就是mii info 只显示一两下就又没东西了， 你那儿是这样么， 设备树我用的如下：

&gem2 {

phy-mode = "sgmii";

phy-handle = ;

//phy-reset-gpio = ;

//phy-reset-active-low;

phy0:ethernet-phy@0x0{

reg = <0x0>;

compatible = "athros,ar8031";

device_type = "ethernet-phy";

xlnx,phy-type = <0x4>;

};

};

ZynqMP> mii info

PHY 0x00: OUI = 0x0000, Model = 0x00, Rev = 0x00, 10baseT, HDX

PHY 0x01: OUI = 0x0000, Model = 0x00, Rev = 0x00, 10baseT, HDX

PHY 0x02: OUI = 0x3FFFC0, Model = 0x00, Rev = 0x00, 10baseT, HDX

PHY 0x03: OUI = 0x0000, Model = 0x00, Rev = 0x00, 10baseT, HDX

ZynqMP> ping 192.168.10.20

ethernet@ff0d0000 Waiting for PHY auto negotiation to complete. done

Using ethernet@ff0d0000 device

ARP Retry count exceeded; starting again

ping failed; host 192.168.10.20 is not alive

ping 不通的。

进入linux系统也没找到eth0

应该还是phy的原因吧？千兆网支持好像看到有帖子将速率降下来就可以，设备树可以参考：

&gem2 {

local-mac-address = [00 0a 35 00 1e 53];

xlnx,eth-mode = <0x1>;

phy-handle = ;

phy0: phy0@7 {

#address-cells = <1>;

#size-cells = <0>;

device_type = "ethernet-phy";

reg = <7>;

};

fixed-link {

speed = <1000>;

full-duplex;

};

};