噪声报警c语言程序,基于单片机噪声报警系统源程序与Proteus仿真电路设计

#include

#include "LCD1602.h"

unsigned char welcome[]={"welcome!"};

unsigned char Show0[6]={"Noise:"};

unsigned char Show1[5]={"dB"};

/*unsigned int code Countnum[60]={ 11,  13,  15,  17,  19,  22,  24,  27,  31,  34,      //T0计数值

39,  44,  49,  55,  62,  69,  78,  87,  98,  110,

123, 138, 155, 174, 195, 219, 246, 276, 309, 347,

390, 438, 491, 550, 618, 693, 778, 873, 979, 1099,

1233,1383,1552,1742,1954,2193,2460,2760,3097,3475,

3899,4375,4909,5508,6180,6934,7780,8729,9794,10989,};*/

unsigned long code Countnum[100]={10,11,12,13,15,17,19,22,25,28,

31,35,39,43,48,54,60,67,75,84,

94,105,117,131,146,163,182,204,228,255,

286,320,359,402,451,506,567,636,713,799,

896,1005,1127,1264,1418,1590,1783,2000,2244,2517,

2824,3168,3556,3989,4475,5020,5632,6319,7089,7953,

8923,10011,11232,12602,14139,15863,17798,19969,22405,25138,

28204,31644,35504,39835,44694,50146,56263,63127,70828,79469,

89164,100042,112247,125941,141305,158544,177886,199588,223937,251257,

281910,316303,354891,398187,446765,501270,562424,631039,708025,794404,};

unsigned char code dB[100][3]={"031","032","033","034","035","036","037","038","039","040",        //T0计数值对应 dB

"041","042","043","044","045","046","047","048","049","050",

"051","052","053","054","055","056","057","058","059","060",

"061","062","063","064","065","066","067","068","069","070",

"071","072","073","074","075","076","077","078","079","080",

"081","082","083","084","085","086","087","088","089","090",

"091","092","093","094","095","096","097","098","099","100",

"101","102","103","104","105","106","107","108","109","110",

"111","112","113","114","115","116","117","118","119","120",

"121","122","123","124","125","126","127","128","129","130",

};

sbit beep=P2^2;

sbit key_1=P2^1;

sbit key_2=P2^0;

//全局变量/

unsigned long count,c;

uchar t,z;

uchar shu,ys;

//函数声明

/************************************

延时子程序

延时时间(xms*1)ms

*************************************/

void delayms(uint xms)           //延时xms

{

uint x,y;

for(x=xms;x>0;x--)

for(y=90;y>0;y--);

}

void key()

{

if (key_1==0)

{

delayms(10);

if (key_1==0)

{

while(key_1==0);

if (shu<99) shu++;

}

}

if (key_2==0)

{

delayms(10);

if (key_2==0)

{

while(key_2==0);

if (shu>0) shu--;

}

}

}

void alarm()

{

ys++;

if (ys>20)

{

ys=0;

beep=!beep;

}

}

//主函数///

void main(void)

{

uint m,n;

uint i;

delayms(1000);

TMOD=0X15;           //T0外部计数 工作方式1    T1定时方式1

EA=0;                 //开总中断

ET1=0;                 //关闭T1

TH0=0;

TL0=0;

TH1=(65536-50000)/256;       //裝初值

TL1=(65536-50000)%256;       //裝初值

init_1602();

WRITE_LCD1602_COM(0x80+3);    //    显示地址

for(i=0; i<6; i++)

{

WRITE_LCD1602_DAT(Show0[i]);

delayms(5);

}

WRITE_LCD1602_COM(0x80+12);           //    显示地址

for(i=0;i<2;i++)

{

WRITE_LCD1602_DAT(Show1[i]);

delayms(5);

}

WRITE_LCD1602_COM(0xc0+3);           //    显示地址

WRITE_LCD1602_byte("Limit:");

WRITE_LCD1602_COM(0xc0+12);           //    显示地址

for(i=0;i<2;i++)

{

WRITE_LCD1602_DAT(Show1[i]);

delayms(5);

}

EA=1;

ET1=1;            //开T1

TR1=1;            //T1开始定时

TR0=1;            //T0开始计数

while(1)

{

key();

WRITE_LCD1602_COM(0xc0+9);

WRITE_LCD1602_DAT(0x30+(shu+31)/100%10);

WRITE_LCD1602_DAT(0x30+(shu+31)/10%10);

WRITE_LCD1602_DAT(0x30+(shu+31)%10);

i=0;

if(count==0)

continue;

while(count>Countnum[i])

{

i++;

}

m=i;

i=0;

WRITE_LCD1602_COM(0x80+9);

for(n=0; n<3; n++)

{

WRITE_LCD1602_DAT(dB[m][n]);

delayms(5);

}

WRITE_LCD1602_COM(0xc0+9);

WRITE_LCD1602_DAT(0x30+(shu+31)/100%10);

WRITE_LCD1602_DAT(0x30+(shu+31)/10%10);

WRITE_LCD1602_DAT(0x30+(shu+31)%10);

if(m>=shu)

{

alarm();

}else

{

beep=1;

}

}

}

void Timer0() interrupt 1

{

z++;

}

void Timer1() interrupt 3

{

TR1=0;      //关闭T1定时

TH1=(65536-50000)/256;

TL1=(65536-50000)%256;

t++;

if(t==20)       //定时1s时间到

{

t=0;

TR0=0;        //T0停止计数

c=z*65535+(TH0*256+TL0);        // 将计数值读取

TH0=0;                        //清空计数值

TL0=0;                       //清空计数值

TR0=1;                           //T0开始计数

count=c;

c=0;

z=0;

}

TR1=1;        //T1开始定时

}