linux拨号失败分配局域网ip,明明拨号成功却上不了网（已解决）

明明拨号成功却上不了网(已解决)

发布时间:2009-02-13 19:52:30来源:红联作者:ljs2002

[i=s] 本帖最后由 ljs2002 于 2009-2-13 20:35 编辑 [/i]

我用pppoe拨号成功可是连不上网，ping dns地址，没有回应，ping网关192.168.0.1可以

我把在终端下操作过程复制了，想让大家帮忙看一下，是怎么回事？这个问题困扰了我好几天，终于解决了，

root@slax:~# pppoe-setup

Welcome to the Roaring Penguin PPPoE client setup. First, I will run

some checks on your system to make sure the PPPoE client is installed

properly...

Looks good! Now, please enter some information:

USER NAME

>>> Enter your PPPoE user name (default bxxxnxnx@sympatico.ca): sy_lijing

INTERFACE

>>> Enter the Ethernet interface connected to the DSL modem

For Solaris, this is likely to be something like /dev/hme0.

For Linux, it will be ethn, where 'n' is a number.

(default eth0):

Do you want the link to come up on demand, or stay up continuously?

If you want it to come up on demand, enter the idle time in seconds

after which the link should be dropped. If you want the link to

stay up permanently, enter 'no' (two letters, lower-case.)

NOTE: Demand-activated links do not interact well with dynamic IP

addresses. You may have some problems with demand-activated links.

>>> Enter the demand value (default no):

DNS

Please enter the IP address of your ISP's primary DNS server.

If your ISP claims that 'the server will provide DNS addresses',

enter 'server' (all lower-case) here.

If you just press enter, I will assume you know what you are

doing and not modify your DNS setup.

>>> Enter the DNS information here: 202.96.69.38

Please enter the IP address of your ISP's secondary DNS server.

If you just press enter, I will assume there is only one DNS server.

>>> Enter the secondary DNS server address here: 202.96.64.68

PASSWORD

>>> Please enter your PPPoE password:

>>> Please re-enter your PPPoE password:

FIREWALLING

Please choose the firewall rules to use. Note that these rules are

very basic. You are strongly encouraged to use a more sophisticated

firewall setup; however, these will provide basic security. If you

are running any servers on your machine, you must choose 'NONE' and

set up firewalling yourself. Otherwise, the firewall rules will deny

access to all standard servers like Web, e-mail, ftp, etc. If you

are using SSH, the rules will block outgoing SSH connections which

allocate a privileged source port.

The firewall choices are:

0 - NONE: This script will not set any firewall rules. You are responsible

for ensuring the security of your machine. You are STRONGLY

recommended to use some kind of firewall rules.

1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation

2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway

for a LAN

>>> Choose a type of firewall (0-2): 0

** Summary of what you entered **

Ethernet Interface: eth0

User name: sy_lijing

Activate-on-demand: No

Primary DNS: 202.96.69.38

Secondary DNS: 202.96.64.68

Firewalling: NONE

>>> Accept these settings and adjust configuration files (y/n)? y

Adjusting /etc/ppp/pppoe.conf

Adjusting /etc/resolv.conf

(But first backing it up to /etc/resolv.conf-bak)

Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets

(But first backing it up to /etc/ppp/pap-secrets-bak)

(But first backing it up to /etc/ppp/chap-secrets-bak)

Congratulations, it should be all set up!

Type 'pppoe-start' to bring up your PPPoE link and 'pppoe-stop' to bring

it down. Type 'pppoe-status' to see the link status.

root@slax:~# pppoe-start

.. Connected!

root@slax:~# pppoe-status

pppoe-status: Link is up and running on interface ppp0

ppp0 Link encap:Point-to-Point Protocol

inet addr:119.119.38.41 P-t-P:119.119.32.1 Mask:255.255.255.255

UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1

RX packets:3 errors:0 dropped:0 overruns:0 frame:0

TX packets:4 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:3

RX bytes:30 (30.0 B) TX bytes:37 (37.0 B)