Linux监控数据包个数,请帮忙完善——监测网卡流量和数据包个数 - 流量监控 - LinuxTone | 运维专家网论坛 - 最棒的Linux运维与开源架构技术交流社区! - Powered b...

本帖最后由 じ☆翔鹏￡ 于 2011-4-20 18:35 编辑

#!/bin/bash

if [ -n "$1" ]; then

eth_name=$1

else

eth_name="eth0"

fi

i=0

send_o=`ifconfig $eth_name | grep bytes | awk '{print $6}' | awk -F : '{print $2}'`

recv_o=`ifconfig $eth_name | grep bytes | awk '{print $2}' | awk -F : '{print $2}'`

send_n=$send_o

recv_n=$recv_o

send_op=`ifconfig $eth_name | grep packets | awk '{print $6}' | awk -F : '{print $2}'`

recv_op=`ifconfig $eth_name | grep packets | awk '{print $2}' | awk -F : '{print $2}'`

send_np=$send_op

recv_np=$recv_op

while [ $i -le 100000 ]; do

send_l=$send_n

recv_l=$recv_n

send_lp=$send_np

recv_lp=$recv_np

sleep 1

send_n=`ifconfig $eth_name | grep bytes | awk '{print $6}' | awk -F : '{print $2}'`

recv_n=`ifconfig $eth_name | grep bytes | awk '{print $2}' | awk -F : '{print $2}'`

send_np=`ifconfig $eth_name | grep packets | awk '{print $6}' | awk -F : '{print $2}'`

recv_np=`ifconfig $eth_name | grep packets | awk '{print $2}' | awk -F : '{print $2}'`

i=`expr $i + 1`

send_r=`expr $send_n - $send_l`

recv_r=`expr $recv_n - $recv_l`

send_rp=`expr $send_np - $send_lp`

recv_rp=`expr $recv_np - $recv_lp`

total_r=`expr $send_r + $recv_r`

send_ra=`expr \( $send_n - $send_o \) / $i`

recv_ra=`expr \( $recv_n - $recv_o \) / $i`

total_ra=`expr $send_ra + $recv_ra`

total_rp=`expr $send_rp + $recv_rp`

send_rap=`expr \( $send_np - $send_op \) / $i`

recv_rap=`expr \( $recv_np - $recv_op \) / $i`

total_rap=`expr $send_rap + $recv_rap`

sendn=`ifconfig $eth_name | grep bytes | awk -F \( '{print $3}' | awk -F \) '{print $1}'`

recvn=`ifconfig $eth_name | grep bytes | awk -F \( '{print $2}' | awk -F \) '{print $1}'`

sendnp=`ifconfig $eth_name | grep packets | awk -F \( '{print $3}' | awk -F \) '{print $1}'`

recvnp=`ifconfig $eth_name | grep packets | awk -F \( '{print $2}' | awk -F \) '{print $1}'`

clear

echo "=================================================="

echo "Last second :   Send rate: $send_r Bytes/sec Recv rate: $recv_r Bytes/sec Total rate: $total_r Bytes/sec"

echo "Average value:   Send rate: $send_ra Bytes/sec Recv rate: $recv_ra Bytes/sec Total rate: $total_ra Bytes/sec"

echo "Total traffic after startup:    Send traffic: $sendn Recv traffic: $recvn"

echo "---------------------------------------------------"

echo "Last second :   Send rate: $send_rp num/sec Recv rate: $recv_rp num/sec Total rate: $total_rp num/sec"

echo "Average value:   Send rate: $send_rap num/sec Recv rate: $recv_rap num/sec Total rate: $total_rap num/sec"

echo "Total traffic after startup:    Send traffic: $sendnp Recv traffic: $recvnp"

echo "=================================================="

done

流量监控实现了，但是我还想显示经过网卡的数据包个数，但是显示不了，请指教。