1【测试目的】
DTCH or DCCH mapped to UL SCH/ DL-SCH / Reserved Logical Channel ID
主要测试的是DTCH映射到UL-SCH, DL-SCH 和保留LCID的功能.
2【测试条件】
LTE Rel8 and UEs supporting E-UTRA
3【PASS LOG 信令流程一览】
4【测试步骤】
7.1.1.2 DTCH or DCCH mapped to UL SCH/ DL-SCH / Reserved Logical Channel ID
7.1.1.2.1 Test Purpose (TP)
(1)
with { UE in E-UTRA RRC_Connected state with DRB [Logical channel ID 3] established }
ensure that {
when { UE receives a MAC PDU on DL SCH and addressed to its CRNTI but including a reserved value for LCID }
then { UE shall not forward the disassembled and demultiplexed SDU on the configured logical channels }
}
(2)
with { UE in E-UTRA RRC_IDLE state and after transmitting a RRCConnectionRequest message }
ensure that {
when { UE receives a MAC PDU on DL SCH and addressed to its CRNTI with value '00011'B as LCID }
then { UE shall forward the disassembled and demultiplexed SDU on the corresponding logical channel }
}
}
[LTE R8]
Table 6.2.1-1: Values of LCID for DL-SCH
Index | LCID values |
00000 | CCCH |
00001-01010 | Identity of the logical channel |
01011-11011 | Reserved |
11100 | UE Contention Resolution Identity |
11101 | Timing Advance |
11110 | DRX Command |
11111 | Padding |
[LTE R10]
Table 6.2.1-1 Values of LCID for DL-SCH
Index | LCID values |
00000 | CCCH |
00001-01010 | Identity of the logical channel |
01011-11010 | Reserved |
11011 | Activation/Deactivation |
11100 | UE Contention Resolution Identity |
11101 | Timing Advance Command |
11110 | DRX Command |
11111 | Padding |
Table 7.1.1.2.3.2-1: Main behaviour
St | Procedure | Message Sequence | TP | Verdict | UE log and comments | |
U - S | Message | |||||
EXCEPTION: IF UE is Release 8 or Release 9, steps 1 and 2 are repeated for decreasing reserved LCID values from 01011 to 11011 ELSE IF UE is Release 10 onwards, steps 1 and 2 are repeated for decreasing reserved LCID values from 01011 to 11010. | - | - | - | - | // 从UE能力上看,UE is Release10, 所以LCID的范围是01011(11) – 11010(26) 2017 Jan 9 08:10:54.001 [DE] 0xB0C0 LTE RRC OTA Packet -- UL_DCCH / UECapabilityInformation // UE 收到 ACTIVATE TEST MODE, the TEST MODE is MODE A: DRB // UE 发送 ACTIVATE TEST MODE COMPLETE, 但是APEX上没有该LOG显示 // UE 收到 CLOSE UE TEST LOOP,开始闭环还回测试 // UE发送CLOSE UE TEST LOOP COMPLETE,同样APEX上也没有显示 | |
1 | The SS transmits a valid MAC PDU containing a RLC PDU except for LCID in MAC Header set to reserved value . | <-- | MAC PDU | - | - | // UE MAC 收到 LCID=11的MAC PDU, UE丢弃 // UE MAC 收到 LCID=12的MAC PDU, 可以看出LCID的变化为生序,UE丢弃 // UE MAC 收到 LCID=25的MAC PDU, UE丢弃。但是这是最后一包保留LCID的MAC PDU.这与协议是不相符的,协议规定对于LTE R10,最后一包保留LCID=26. 这应该是安利仪表的一个bug. |
2 | Check: does the UE transmit a Scheduling Request on PUCCH within 5 seconds after step 1? | --> | (SR) | 1 | 1 | F |
3 | The SS Transmits a valid MAC PDU containing RLC PDU with LCID in MAC Header set correctly to DRB 00011. | <-- | MAC PDU | - | - | // UE MAC 收到 LCID=3的MAC PDU (346/8), 这是一包合法MAC PDU |
4 | Check: does the UE transmit a Scheduling Request on PUCCH? | --> | (SR) | 2 | 2 | P // UE send SR at 347/5 2017 Jan 9 08:12:14.327 [CC] 0xB16D LTE GM TX Report |
5 | The SS sends an UL grant suitable for the loop back PDU to transmitted | <-- | (UL Grant) | - | - | // UE receive the UL GRANT at 347/9 |
6 | Check: does the UE transmit a MAC PDU with LCID set to DRB 00011? | --> | MAC PDU | 2 | 2 | P // UE 发送UL MAC PDU LCID=3 |