Xprog 5.5.1 fix xprog-m 5.0 software error and authorization error

Important Note:
I am not stating or encouraging you operate by following the next steps to update from Xprog 5.0 to Xprog 5.5.1 if you do not have knowledge and skills to remove the chip, otherwise it may screw up the chip.
The information provided here are for information only and have no ties or responsibility with eobd2 supplier, as they were all taken at random sites on the internet and can be accessed publicly.
Update Xprog 5.0 to Xprog 5.5.1 will solve “Unknown command, software error” and fix authorization error.
Xprog 5.5.1 download:
https://mega.co.nz/#!CYIx2A6a!T5s_8eLwA5Y6AuPjc1l5E6yKCbIPIAr3OoCL8Uv3ajk
Xprog 5.5.1 Update Steps:
You must programmer step by step ,i used with USB-UPA:
1. Erase chip atmega 64
2. Program eeprom , Flash
3. Set Lock bits and fuse bits. Program lock bits, fuse bits.
4. Copy Xprogbox 5.51 to C:\ and run Xprognew.reg
5. Run XprogDesktop.exe and update .
Working ECU after install Xprog 5.5.1:
1.    All works ok cas 2 cas3 read and write in first time
2.    my old xprog-m 5.0 now have the 5.51 version succesfully installed!, I already tested with Infineon xc23xx, Mac7242, SPI, I2C, Microwire eeproms, some 9S12, HC11, HC05 and TMS. Works great, verify error also fixed with update. Before this update I can’t read/write the HC05H12, now it’s working!. All authorizations activated.
XPROG1image001
Question:
I have problem with my XPROG. After update 5.5.1, I have all authorization but when I try read or write device I got error “Unknown command. Software error”
image002
Solution: Software must be in c:/ ,update .reg files ,reprogram Atmega 64
1Program EEprom
2 program Flash
3 Lock bits -Program
4 Fuse Bits Program
Question:
I read flash for CAS 3 xprog read it as 2048kb it should 512kb
Solution:
This is normal for xprog. Rosfar on the other side read only 512k and is correct also. Xprog use the whole range of addresses for this mcu from 0 to 1FFFFF, despite the fact that only some blocks are used. The unused blocks are filled with FF. Rosfar use only the blocks that contains data hence only 512k is produced.
I made a script for upa to convert from one to the other format.
http://down.eobd2.fr/rosfarxprog.zip
You will need to have upa 1.3 installed but no need to be plugged in. Load your dump in upa and use the script to convert your dump. The script has 2 choices, convert from rosfar to xprog or convert from xprog to rosfar, then you must save the converted dump. It is easy to use.
Question:
I had problems with security bits
I’ll try to wake
report results
http://down.eobd2.fr/fuse-brick.pdf
Solution:
To prevent atmega brick do not touch JTAG and SPIEN fuses.
Also this firmware has bugs.
For example,if you got an MCU that hangs on bypass security,when you press cancel,the windows program is cancelled but the programmer is still doing bypass security.
To get it out of that bug,you need to disconnect it first,and reconnect again.
Question:
Can I update xprog m with programmer tl866? it’s have atmega64 but I not know how to connect.
Solution:
use in-circuit connection.
image003
TL866 is produced in two options – with and without isp

转载于:https://www.cnblogs.com/eobd2/p/4263747.html

  • 0
    点赞
  • 0
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值