java switch table,JVM的LookupSwitch和TableSwitch之间的区别？

I have some difficulty to understand LookUpSwitch and TableSwitch in Java bytecode.

If I understand well, both LookUpSwitch and TableSwitch correspond to the switch statement of Java source? Why one JAVA statement generates 2 different bytecodes?

Jasmin documentation of each:

解决方案

The difference is that a lookupswitch uses a table with keys and labels, yet a tableswitch uses a table with labels only.

When performing a tableswitch, the int value on top of stack is directly used as an index into the table to grab the jump destination and perform the jump immediately. The whole lookup+jump process is an O(1) operation, that means it's blazing fast.

When performing a lookupswitch, the int value on top of the stack is compared against the keys in the table until a match is found and then the jump destination next to this key is used to perform the jump. Since a lookupswitch table always must be sorted so that keyX < keyY for every X < Y, the whole lookup+jump process is a O(log n) operation as the key will be searched using a binary search algorithm (it's not necessary to compare the int value against all possible keys to find a match or to determine that none of the keys matches). O(log n) is somewhat slower than O(1), yet it is still okay since many well known algorithms are O(log n) and these are usually considered fast; even O(n) or O(n * log n) is still considered a pretty good algorithm (slow/bad algorithms have O(n^2), O(n^3), or even worse).

The decision which instruction to use is made by the compiler based upon the fact how compact the switch statement is, e.g.

switch (inputValue) {

case 1: // ...

case 2: // ...

case 3: // ...

default: // ...

}

The switch above is perfectly compact, it has no numeric "holes". The compiler will create a tableswitch like this:

tableswitch 1 3

OneLabel

TwoLabel

ThreeLabel

default: DefaultLabel

The pseudo code from the Jasmin page explains this pretty well:

int val = pop(); // pop an int from the stack

if (val < low || val > high) { // if its less than or greater than ,

pc += default; // branch to default

} else { // otherwise

pc += table[val - low]; // branch to entry in table

}

This code is pretty clear on how such a tableswitch works. val is inputValue, low would be 1 (the lowest case value in the switch) and high would be 3 (the highest case value in the switch).

Even with some holes a switch can be compact, e.g.

switch (inputValue) {

case 1: // ...

case 3: // ...

case 4: // ...

case 5: // ...

default: // ...

}

The switch above is "almost compact", it only has a single hole. A compiler could generate the following instruction:

tableswitch 1 6

OneLabel

FakeTwoLabel

ThreeLabel

FourLabel

FiveLabel

default: DefaultLabel

; <...code left out...>

FakeTwoLabel:

DefaultLabel:

; default code

As you can see, the compiler has to add a fake case for 2, FakeTwoLabel. Since 2 is no real value of the switch, FakeTwoLabel is in fact a label that changes code flow exactly where the default case is located, since a value of 2 should in fact execute the default case.

So a switch doesn't have to be perfectly compact for the compiler to create a tableswitch, yet it should at least be pretty close to compactness. Now consider the following switch:

switch (inputValue) {

case 1: // ...

case 10: // ...

case 100: // ...

case 1000: // ...

default: // ...

}

This switch is nowhere near compactness, it has more than hundred times more holes than values. One would call this a spare switch. The compiler would have to generate almost thousand fake cases to express this switch as a tableswitch. The result would be a huge table, blowing up the size of the class file dramatically. This is not practical. Instead it will generate a lookupswitch:

lookupswitch

1 : Label1

10 : Label10

100 : Label100

1000 : Label1000

default : DefaultLabel

This table has only 5 entries, instead of over thousand ones. The table has 4 real values, O(log 4) is 2 (log is here log to the base of 2 BTW, not to the base of 10, since computer operate on binary numbers). That means it takes the VM at most two comparisons to find the label for the inputValue or to come to the conclusion, that the value is not in the table and thus the default value must be executed. Even if the table had 100 entries, it would take the VM at most 7 comparisons to find the correct label or decide to jump to the default label (and 7 comparisons is a lot less than 100 comparisons, don't you think?).

So it's nonsense that these two instructions are interchangeable or that the reason for two instructions has historical reasons. There are two instructions for two different kind of situations, one for switches with compact values (for maximum speed) and one for switches with spare values (not maximum speed, yet still good speed and very compact table representation regardless all the numeric holes).