linux 模拟arm,运用skyeye-1.3.3_testsuite软件模拟ARM+Linux嵌入式系统（基于skyeye1.3.3）...

(skyeye) In start_all_thread, the thread 1 is set to running

(running) Bus read error, can not find corresponding bank for addr 0x0,pc=0x300083b0

Linux version 2.6.30.5 (akaedu@akaedu-desktop) (gcc version 4.2.1) #4 Fri Jun 18 11:24:57 CST 2010

CPU: ARM920T [41009200] revision 0 (ARMvundefined/unknown), cr=00003177

CPU: VIVT data cache, VIVT instruction cache

Machine: SMDK2440

Warning: bad configuration page, trying to continue

Memory policy: ECC disabled, Data cache writeback

CPU S3C2440 (id 0x32440000)

S3C24XX Clocks, (c) 2004 Simtec Electronics

S3C244X: core 176.117 MHz, memory 88.058 MHz, peripheral 44.029 MHz

CLOCK: Slow mode (2.116 MHz), fast, MPLL on, UPLL on

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128

Kernel command line: mem=32M console=ttySAC0 root=/dev/ram initrd=0x30800000,0x00800000 ramdisk_size=8192 rw

NR_IRQS:99

irq: clearing pending ext status ffffffff

PID hash table entries: 128 (order: 7, 512 bytes)

Console: colour dummy device 80x30

console [ttySAC0] enabled

Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

Memory: 32MB = 32MB total

Memory: 20204KB available (3548K code, 331K data, 144K init, 0K highmem)

Calibrating delay loop... 25.60 BogoMIPS (lpj=64000)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

net_namespace: 936 bytes

NET: Registered protocol family 16

S3C Power Management, Copyright 2004 Simtec Electronics

S3C2440: Initialising architecture

S3C2440: IRQ Support

S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics

DMA channel 0 at c2808000, irq 33

DMA channel 1 at c2808040, irq 34

DMA channel 2 at c2808080, irq 35

DMA channel 3 at c28080c0, irq 36

S3C244X: Clock Support, DVS on

bio: create slab at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

s3c2440-i2c s3c2440-i2c: slave address 0x10

s3c2440-i2c s3c2440-i2c: bus frequency set to 85 KHz

s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 1024 (order: 1, 8192 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 1024 bind 1024)

TCP reno registered

NET: Registered protocol family 1

Trying to unpack rootfs image as initramfs...

rootfs image is not initramfs (junk in compressed archive); looks like an initrd

Freeing initrd memory: 8192K

NetWinder Floating Point Emulator V0.97 (extended precision)

JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.

ROMFS MTD (C) 2007 Red Hat, Inc.

msgmni has been set to 55

io scheduler noop registered

io scheduler anticipatory registered (default)

io scheduler deadline registered

io scheduler cfq registered

Console: switching to colour frame buffer device 30x40

fb0: s3c2410fb frame buffer device

lp: driver loaded but no devices found

ppdev: user-space parallel port driver

s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440

s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440

s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440

brd: module loaded

loop: module loaded

Uniform Multi-Platform E-IDE driver

ide-gd driver 1.18

ide-cd driver 5.00

Driver 'sd' needs updating - please use bus_type methods

dm9000 Ethernet Driver, V1.31

S3C24XX NAND Driver, (c) 2004 Simtec Electronics

s3c2440-nand s3c2440-nand: Tacls=2, 22ns Twrph0=6 68ns, Twrph1=2 22ns

No NAND device found!!!

usbmon: debugfs is not available

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

s3c2410-ohci s3c2410-ohci: S3C24XX OHCI

s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1

s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000

s3c2410-ohci s3c2410-ohci: USB HC takeover failed!  (BIOS/SMM bug)

s3c2410-ohci s3c2410-ohci: startup error -16

s3c2410-ohci s3c2410-ohci: USB bus 1 deregistered

s3c2410-ohci: probe of s3c2410-ohci failed with error -16

usbcore: registered new interface driver libusual

usbcore: registered new interface driver usbserial

USB Serial support registered for generic

usbcore: registered new interface driver usbserial_generic

usbserial: USB Serial Driver core

USB Serial support registered for FTDI USB Serial Device

usbcore: registered new interface driver ftdi_sio

ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver

USB Serial support registered for pl2303

usbcore: registered new interface driver pl2303

pl2303: Prolific PL2303 USB to serial adaptor driver

mice: PS/2 mouse device common for all mice

S3C24XX RTC, (c) 2004,2006 Simtec Electronics

S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics

s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq abled

Advanced Linux Sound Architecture Driver Version 1.0.20.

ALSA device list:

No soundcards found.

TCP cubic registered

NET: Registered protocol family 17

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

RAMDISK: ext2 filesystem found at block 0

RAMDISK: Loading 2048KiB [1 disk] into ram disk... done.

VFS: Mounted root (ext2 filesystem) on device 1:0.

Freeing init memory: 144K

SIOCSIFADDR: No such device

SIOCGIFFLAGS: No such device

Welcome to

_      _____      __   __    _      _

/ \    /  __ \    /  \_/  \  | |    |_|

/ _ \   | |  | |  / /\   /\ \ | |     _ ____  _   _  _  _

/ /_\ \  | |__| | / /  \_/  \ \| |    | |  _ \| | | |\ \/ /

/ /___\ \ | |__\ \ | |       | || |___ | | |_| | |_| |/    \

/_/\_\| |   \_\|_|       |_||_____||_|_| |_|\____|\_/\_/

ARMLinux for Skyeye

For further information please check:

BusyBox v1.00 (2004.12.27-02:03+0000) Built-in shell (ash)

Enter 'help' for a list of built-in commands.

/bin/ash: can't access tty; job control turned off

/ #