e13服务器信息解释失败,dell 2850服务器故障,错误代码解释

错误代码：

EB10C: ECC Uncorr Err/ EB110:SBE Log Disabled等错误是和内存有关系。

E0000 OVRFLW CHECK LOG LCD overflow message.

A maximum of three error messages can display sequentially on the LCD. The fourth message displays as the standard overflow message. Check the SEL for details on the events.

I0000 BIB Unable to read BIOS initial block or BIB invalid. Clear NVRAM, or try reflashing the BIOS.

IS000 Intrusion System Intrusion is occuring. Close chassis.

E1000 FAIL SAFE, CALL SUPPORT Failsafe event. Capture the system.

E1000 MISCONFIG. CALL SUPPORT System mis-configuration. Incorrect processors, missing VRMs etc. would cause this kind of error.

E0119 TEMP AMBIENT Ambient system temperature is out of acceptable range. See "Troubleshooting System Cooling Problems" in "Troubleshooting Your System."

E0119  TEMP BP Backplane board is out of acceptable temperature range. See "Troubleshooting System Cooling Problems" in "Troubleshooting Your System."

E0119 TEMP CPU n Specified microprocessor is out of acceptable temperature range. See "Troubleshooting System Cooling Problems" in "Troubleshooting Your System." If the problem persists, ensure that the microprocessor heat sinks are properly installed (see "Replacing a Processor" in "Installing System Options").

E0119 TEMP PROC # Processor # temperature is out of acceptable temperature range.

E0119 Temp Planar System board temperature is out of acceptable temperature range.

E0119 Temp Ambient System ambient temperature is out of acceptable temperature range.

E0119 Temp RISER Riser temperature is out of acceptable temperature range.

E0119 TEMP SYSTEM System board is out of acceptable temperature range. See "Troubleshooting System Cooling Problems" in "Troubleshooting Your System."

E0212 PROC VTT Processor VTT voltage is out of acceptable voltage range.

E0212 VOLT 3.3 System power supply is out of acceptable voltage range; faulty or improperly installed power supply. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

E0212 VOLT 5 System power supply is out of acceptable voltage range; faulty or improperly installed power supply. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

E0212 VOLT 12 System power supply is out of acceptable voltage range; faulty or improperly installed power supply. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

E0212 VOLT BATT Faulty battery; faulty system board. See "Troubleshooting the System Battery" in "Troubleshooting Your System."

E0212 Volt batt CMOS Motherboard CMOS battery is out of acceptable voltage range.

E0212 Volt batt ROMB ROMB battery is out of acceptable voltage range.

E0212 VOLT BP 12 Backplane board is out of acceptable voltage range. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

E0212 VOLT BP 3.3 Backplane board is out of acceptable voltage range. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

E0212 VOLT BP 5 Backplane board is out of acceptable voltage range. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

E0212 VOLT NIC 1.8V Integrated NIC voltage is out of acceptable range; faulty or improperly installed power supply; faulty system board. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

E0212 VOLT NIC 2.5V Integrated NIC voltage is out of acceptable range; faulty or improperly installed power supply; faulty systemboard. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

E0212 VOLT PLANAR REG System board is out of acceptable voltage range; faulty or improperly installed system board. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

E0212 Volt PG 1 35V Video 1.35V voltage is out of acceptable voltage range.

E0212 Volt PG 1 5V 1.5 V voltage is out of acceptable voltage range.

E0212 Volt PG 1 8V 1.8 V voltage is out of acceptable voltage range.

E0212 Volt PG 1 8V Video Video 1.8v voltage is out of acceptable voltage range.

E0212 Volt PG 3 3V 3.3 V voltage is out of acceptable voltage range.

E0212 Volt PG 5 V 5 V voltage is out of acceptable voltage range.

E0212 Volt RISER 5V Riser 5V voltage is out of acceptable voltage range.

E0212 Volt RISER Riser voltage is out of acceptable voltage range.

E0276 PROC # STATUS Process # status. Check the process #, clear NVRAM.

E0276 PROC # VCORE Processor # VCORE voltage is out of acceptable range.

E0276 VRM # PG VRM # voltage is out of acceptable range.

E0276 PS AC Current Power supply AC current is out of acceptable range. Check Power source, power supply.

E0276 PS Over Current Power supply current is out of acceptable range. Check Power source, power supply.

E0276 kPS Over Current Power supply current is out of acceptable range. Check Power source, power supply.

E02F1 OS HANG Operating system hang.

E0412 RPM Fan # Fan # RPM is out of acceptable range. Check Fan # connection, reseat.

E0412 FAN Redundancy Lost Fan redundancy lost. Check fan connections.

E0412 RPM Fan PS Blank Power supply fan RPM is out of acceptable range. Check power supply connections.

E0319 PCI OVER CURRENT Faulty or improperly installed expansion card. See "Troubleshooting Expansion Cards" in "Troubleshooting Your System."

E0412 RPM FAN n Specified cooling fan is faulty, improperly installed, or missing. See "Troubleshooting System Cooling Problems" in "Troubleshooting Your System."

E0780 MISSING CPU 1 Microprocessor is not installed in socket 1. Install a microprocessor in socket 1 (see "Replacing a Processor" in "Installing System Options").

E07F0 PROC # IERR PROC # IERR asserted. Check processor # connection, flash firmware BIOS, BMC.

E07FA PROC # Thermtrip Processor # temperature is out of acceptable temperature range.

E07F0 CPU IERR Faulty or improperly installed microprocessor. See "Troubleshooting the Microprocessors" in "Troubleshooting Your System."

E07F1 TEMP CPU n HOT Specified microprocessor is out of acceptable temperature range and has halted operation. See "Troubleshooting System Cooling Problems" in "Troubleshooting Your System." If the problem persists, ensure that the microprocessor heat sinks are properly installed (see "Replacing a Processor" in "Installing System Options").

E07F4 POST CACHE Faulty or improperly installed microprocessor. See "Troubleshooting the Microprocessors" in "Troubleshooting Your System."

E07F4 POST CPU REG Faulty or improperly installed microprocessor. See "Troubleshooting the Microprocessors" in "Troubleshooting Your System."

E07F4 POST CPU SMI SMI handler failed to initialize; faulty system board. See "Getting Help."

E07FA TEMP CPU n THERM Specified microprocessor is out of acceptable temperature range and is operating at a reduced speed, or frequency. See "Troubleshooting System Cooling Problems" in "Troubleshooting Your System." If the problem persists, ensure that the microprocessor heat sinks are properly installed (see "Replacing a Processor" in "Installing System Options").

E0780 PROC # Presence Processor # is presence. (But other processor(s) missing.

E0780 PROC # Config Err PROC # configuration error. Check BIOS and ESM firmware levels.

E0876 POWER PS n No power available from the specified power supply; specified power supply is improperly installed or faulty. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

E0876 PS # Missing Power supply # is missing. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

E0876 PS # Status Power supply # status. Check power supply # connections.

E0876 PS # Predictive Power supply # is predictive failure Replacement required.

E0876 PS # AC LOST Power supply # AC is lost. Check power supply # connections.

E0876 PS # AC RANGE Power supply # AC is out of acceptable range. Check power supply # connections source power.

E0876 PS Redundancy Power supply redundancy lost. Check power supply connections source power.

E0880 INSUFFICIENT PS Insufficient power is being supplied to the system; power supplies are improperly installed, faulty, or missing. See "Troubleshooting Redundant Power Supplies" in "Troubleshooting Your System."

电源模块安装不正确或是有问题。

E0CB2 MEM SPARE ROW Correctable errors threshold was met in a memory bank: errors were remapped to the spare row. See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0CF1 MBE DIMM Bank n Memory modules installed in the specified bank are not the same type and size; faulty memory module(s). Ensure that both memory modules in the bank are the same type and size and that they are properly installed. If the problem persists, see "Troubleshooting System Memory" in "Troubleshooting Your System."

E0CF1 POST MEM 64K Parity failure in the first 64 KB of main memory. See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0CF1 POST NO MEMORY Main-memory refresh verification failure. See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0CF5 LOG DISABLE SBE Multiple single-bit errors on a single memory module. See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0D76 BP DRIVE FAIL n Faulty or improperly installed hard drive or RAID controller. See "Troubleshooting SCSI Hard Drives" "Troubleshooting a RAID Controller Card, " and "Troubleshooting the Integrated RAID Controller" in "Troubleshooting Your System."

E0D76 1x2 DRIVE FAIL n Faulty or improperly installed hard drive or RAID controller. See "Troubleshooting SCSI Hard Drives" "Troubleshooting a RAID Controller Card, " and "Troubleshooting the Integrated RAID Controller" in "Troubleshooting Your System."

E0F04 POST CMOS CMOS write/read failure; faulty system board. See "Getting Help."

E0F04 POST CPU SPEED Microprocessor speed control sequence failure. See "Getting Help."

E0F04 POST DMA INIT DMA initialization failure; DMA page register write/read failure. See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0F04 POST DMA REG Faulty system board. See "Getting Help."

E0F04  POST KYB CNTRL Faulty keyboard controller; faulty system board. See "Getting Help."

E0F04 POST MEM RFSH Main-memory refresh verification failure. See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0F04 POST PIC REG Master or slave PIC register test failure. See "Getting Help."

E0F04 POST SHADOW BIOS-shadowing failure. See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0F04 POST SHD TEST Shutdown test failure. See "Troubleshooting System Memory" in "Troubleshooting Your System."

E0F04 POST SIO Super I/O chip failure; faulty system board. See "Getting Help."

E0F04 POST TIMER Programmable interval timer test failure; faulty system board. See "Getting Help."

E0F0B POST ROM CHKSUM Faulty or improperly installed expansion card. See "Troubleshooting Expansion Cards" in "Troubleshooting Your System."

E0F0C VID MATCH CPU n Specified microprocessor is faulty, unsupported, improperly installed, or missing. See "Troubleshooting the Microprocessors" in "Troubleshooting Your System."

E10F3 LOG DISABLE BIOS BIOS disabled logging errors. Check the SEL for details on the errors.

E13F2 IO CHANNEL CHECK  Faulty or improperly installed expansion card; faulty system board. See "Troubleshooting Expansion Cards" in "Troubleshooting Your System."

E13F4 PCI PARITY Faulty or improperly installed expansion card; faulty system board. See "Troubleshooting Expansion Cards" in "Troubleshooting Your System."

E13F5 PCI SYSTEM Faulty or improperly installed expansion card; faulty system board. See "Troubleshooting Expansion Cards" in "Troubleshooting Your System."

E13F8 CPU BUS INIT Faulty or improperly installed microprocessor or system board. See "Troubleshooting the Microprocessors" in "Troubleshooting Your System." If the problem persists, see "Getting Help."

E13F8 CPU BUS PARITY Faulty system board. See "Getting Help."

E13F8  CPU MCKERR Machine check error; faulty or improperly installed microprocessor; faulty system board. See "Troubleshooting the Microprocessors" in "Troubleshooting Your System."

E13F8 HOST BUS  See "Getting Help."

E13F8 HOST TO PCI BUS Faulty system board. See "Getting Help."

E13F8 MEM CONTROLLER Faulty or improperly installed memory module; faulty system board. See "Troubleshooting System Memory" in "Troubleshooting Your System."

E1580 POWER CONTROL Faulty system board. See "Getting Help."

E20F1 OS HANG Operating system watchdog timer timed out. Restart your system. If the problem persists, see your operating system documentation.

EB10C ECC Uncorr Err ECC Uncorr Err Bank # System memory uncorrectable ECC errors. (on memory bank #) Check memory.

IB10C Memory Spared BIOS Memory Spare Bank Informational message

IB10C Memory Mirrored BIOS Memory Mirror Bank Informational message

IB10C Memory Raid BIOS Memory Raid Bank Informational message

EB107 MEMORY MIRRORED Memory mirroring enabled  Information only.

EB107 MEMORY SPARED Memory spare bank enabled Information only.

EB107 PROC Protocol Err Processor Protocol Error. NVRAM Clear, check BIOS, ESM firmware.

EB107 PROC Bus PERR Processor Bus Parity Error. NVRAM Clear, check BIOS, ESM firmware.

EB107 PROC Machine Chk Process Machine Check Error. NVRAM Clear, check BIOS, ESM firmware.

EB107 PROC Init Err Processor Initialization Error. NVRAM Clear, check BIOS, ESM firmware.

EB107 PROC Hot Processor is out of acceptable temperature range and has halted operation. NVRAM Clear, check BIOS, ESM firmware. Check tempeture of area server is in.

EB113 I/O Channel Chk System IO Channel Check Information only.

EB113 PCI Parity Err PCI Parity Error Check PCI Connections, cards.

EB113 PCI System Err PCI System Error Check PCI Connections, cards.

EB113 PCIE Fatal Err PCIE Fatal Error Check PCIE connection cards.

EB113 PCIE Non Fatal Err PCIE Non Fatal Error Check PCIE connection cards.

EB113 Chipset Err Chipset Error Check BIOS, BMC firmware or clear NVRAM.

IB110 SBE Log Disabled Single Bit Error Log Disabled. Check ESM log. Troubleshoot memory.

IB110 Logging Disabled BIOS Logging Disabled. Check ESM log. Clear to enable logging again.

EB112 Unknown BIOS Unknown Error. NVRAM Clear, check BIOS, ESM firmware.

EFFF0 RAC ERROR Remote access controller firmware failure; faulty system board. See "Getting Help."

EFFF1 POST ERROR  BIOS error. Update the BIOS firmware (see "Getting Help").

EFFF2 BP ERROR Faulty or improperly installed backplane board. Ensure that the interface cables are securely connected to the backplane board (see "Installing Drives"). Reseat the backplane and daughter cards If the problem persists

温馨提示

感谢您浏览《dell 2850服务器故障,错误代码解释》

现邀请您关注我们的【5分享】(fivsha)公众号，你将获取更多的IT资源。

如果有疑问也可以在公众号里面回复您遇到的问题或是点击在线帮助联系我们。