MySQL复制能够保证数据的冗余的同时可以做读写分离来分担系统压力，如果是主主复制还可以很好的避免主节点的单点故障。然而MySQL主主复制存在一些问题无法满足我们的实际需要：未提供统一访问入口来实现负载均衡，如果其中master宕掉的话需要手动切换到另外一个master，而不能自动进行切换。前面介绍了Mysql+Keepalived双主热备高可用方案记录，那篇文档里没有使用到LVS(实现负载均衡)，而下面要介绍的就是如何通过Keepalived+LVS方式来是实现MySQL的高可用性，利用LVS实现MySQL的读写负载均衡，Keepalived避免节点出现单点故障，同时解决以上问题。
Keepalived是一个基于VRRP(虚拟路由冗余协议)可用来实现服务高可用性的软件方案，避免出现单点故障。Keepalived一般用来实现轻量级高可用性，且不需要共享存储，一般用于两个节点之间，常见有LVS+Keepalived、Nginx+Keepalived组合。
LVS(Linux Virtual Server)是一个高可用性虚拟的服务器集群系统。本项目在1998年5月由章文嵩博士成立，是中国国内最早出现的自由软件项目之一。LVS主要用于多服务器的负载均衡，作用于网络层。LVS构建的服务器集群系统中，前端的负载均衡层被称为Director Server；后端提供服务的服务器组层被称为Real Server。通过下图可以大致了解LVS的基础架构。
LVS有三种工作模式，分别是：
1)DR(Direct Routing 直接路由)模式。 DR可以支持相当多的Real Server，但需要保证Director Server(分发器)虚拟网卡与物理网卡在同一网段，并且后端Real Server的vip要建立在本地回环口lo设备上，这样做是为了防止ip冲突；DR模式的好处是进站流量经过Director Server，出站流量不经过Director Server，减轻了Director Server的负载压力。
2)NAT(Network Address Translation 网络地址转换)模式。NAT扩展性有限，无法支持更多的Real Server，因为所有的请求包和应答包都需要Director Server进行解析再生，这样就很影响效率。
3)TUN(Tunneling IP隧道)模式。TUN模式能够支持更多的Real Server，但需要所有服务器支持IP隧道协议；
LVS负载均衡有10中调度算法，分别是：rr(轮询)、wrr(加权轮询)、lc、wlc、lblc、lblcr、dh、sh、sed、nq
以下详细记录了Mysql在主主同步环境下，利用LVS实现Mysql的读写负责均衡以及使用Keepalived心跳测试避免节点出现单点故障，实现故障转移的高可用。
1)高可用方案的环境准备
LVS_Master： 182.148.15.237
LVS_Backup： 182.148.15.236
MySQL1 Real Server： 182.148.15.233
MySQL2 Real Server： 182.148.15.238
VIP： 182.148.15.239
OS: CentOS 6.8
温馨提示：LVS_Master和LVS_Backup充当的是Director Server分发器的角色。
这里的LVS采用DR模式，即"进站流量经过Director Server分发器，出站流量不经过分发器"，这就要求：
1)LVS_Master和LVS_Backup需要将VIP绑定在其正常提供服务的网卡上(这里指182.48.115.0网段所在的网卡)，netmask和对于网卡设备一致。
2)后端的Real Server要在本地回环口lo上绑定vip(防止ip冲突)
2)环境部署记录如下
a)Mysql主主热备环境部署
MySQL1 Real Server1和MySQL2 Real Server的主主热备可以参考Mysql+Keepalived双主热备高可用操作记录中对应部分。
b)Keepalived安装
LVS_Master和LVS_Backup的keepalived安装，也可以参考Mysql+Keepalived双主热备高可用操作记录中对应部分。
c)LVS安装
LVS_Master和LVS_Backup两台机器安装步骤一样
首先打开两台机器的ip_forward转发功能
[root@LVS_Master ~]# echo "1" > /proc/sys/net/ipv4/ip_forward
先下载ipvsadm
[root@LVS_Master ~]# cd /usr/local/src/
[root@LVS_Master src]# wget http://www.linuxvirtualserver.org/software/kernel-2.6/ipvsadm-1.26.tar.gz
需要安装以下软件包
[root@LVS_Master src]# yum install -y libnl* popt*
查看是否加载lvs模块
[root@LVS_Master src]# modprobe -l |grep ipvs
解压安装
[root@LVS_Master src]# ln -s /usr/src/kernels/2.6.32-431.5.1.el6.x86_64/ /usr/src/linux
[root@LVS_Master src]# tar -zxvf ipvsadm-1.26.tar.gz
[root@LVS_Master src]# cd ipvsadm-1.26
[root@LVS_Master ipvsadm-1.26]# make && make install
LVS安装完成，查看当前LVS集群
[root@LVS_Master ipvsadm-1.26]# ipvsadm -L -n
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
d)编写LVS启动脚本/etc/init.d/realserver
1)在MySQL1 Real Server服务器上的操作
[root@MySQL1 ~]# vim /etc/init.d/realserver
#!/bin/sh
VIP=182.148.15.239
. /etc/rc.d/init.d/functions
case "$1" in
# 禁用本地的ARP请求、绑定本地回环地址
start)
/sbin/ifconfig lo down
/sbin/ifconfig lo up
echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/lo/arp_announce
echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce
/sbin/sysctl -p >/dev/null 2>&1
/sbin/ifconfig lo:0 $VIP netmask 255.255.255.255 up #在回环地址上绑定VIP，设定掩码，与Direct Server(自身)上的IP保持通信
/sbin/route add -host $VIP dev lo:0
echo "LVS-DR real server starts successfully.\n"
;;
stop)
/sbin/ifconfig lo:0 down
/sbin/route del $VIP >/dev/null 2>&1
echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/lo/arp_announce
echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce
echo "LVS-DR real server stopped.\n"
;;
status)
isLoOn=`/sbin/ifconfig lo:0 | grep "$VIP"`
isRoOn=`/bin/netstat -rn | grep "$VIP"`
if [ "$isLoON" == "" -a "$isRoOn" == "" ]; then
echo "LVS-DR real server has run yet."
else
echo "LVS-DR real server is running."
fi
exit 3
;;
*)
echo "Usage: $0 {start|stop|status}"
exit 1
esac
exit 0
将lvs脚本加入开机自启动
[root@MySQL1 ~]# chmod +x /etc/init.d/realserver
[root@MySQL1 ~]# echo "/etc/init.d/realserver" >> /etc/rc.d/rc.local
启动LVS脚本
[root@MySQL1 ~]# service realserver start
LVS-DR real server starts successfully.\n
查看MySQL1 Real Server服务器，发现VIP已经成功绑定到本地回环口lo上了
[root@MySQL1 ~]# ifconfig
eth0 Link encap:Ethernet HWaddr 52:54:00:D1:27:75
inet addr:182.148.15.233 Bcast:182.148.15.255 Mask:255.255.255.224
inet6 addr: fe80::5054:ff:fed1:2775/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:598406 errors:0 dropped:0 overruns:0 frame:0
TX packets:12050 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:78790653 (75.1 MiB) TX bytes:33151764 (31.6 MiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:483 errors:0 dropped:0 overruns:0 frame:0
TX packets:483 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:55807 (54.4 KiB) TX bytes:55807 (54.4 KiB)
lo:0 Link encap:Local Loopback
inet addr:182.148.15.239 Mask:255.255.255.255
UP LOOPBACK RUNNING MTU:65536 Metric:1
2)在MySQL2 Real Server服务器上的操作
[root@MySQL2 ~]# vim /etc/init.d/realserver //这个脚本在后端Real Server上都是一样的内容
#!/bin/sh
VIP=182.148.15.239
. /etc/rc.d/init.d/functions
case "$1" in
start)
/sbin/ifconfig lo down
/sbin/ifconfig lo up
echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/lo/arp_announce
echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce
/sbin/sysctl -p >/dev/null 2>&1
/sbin/ifconfig lo:0 $VIP netmask 255.255.255.255 up
/sbin/route add -host $VIP dev lo:0
echo "LVS-DR real server starts successfully.\n"
;;
stop)
/sbin/ifconfig lo:0 down
/sbin/route del $VIP >/dev/null 2>&1
echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/lo/arp_announce
echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce
echo "LVS-DR real server stopped.\n"
;;
status)
isLoOn=`/sbin/ifconfig lo:0 | grep "$VIP"`
isRoOn=`/bin/netstat -rn | grep "$VIP"`
if [ "$isLoON" == "" -a "$isRoOn" == "" ]; then
echo "LVS-DR real server has run yet."
else
echo "LVS-DR real server is running."
fi
exit 3
;;
*)
echo "Usage: $0 {start|stop|status}"
exit 1
esac
exit 0
将lvs脚本加入开机自启动并启动lvs脚本
[root@MySQL2 ~]# chmod +x /etc/init.d/realserver
[root@MySQL2 ~]# echo "/etc/init.d/realserver" >> /etc/rc.d/rc.local
[root@MySQL2 ~]# service realserver start
LVS-DR real server starts successfully.\n
[root@MySQL2 ~]# ifconfig
eth0 Link encap:Ethernet HWaddr 52:54:00:3B:33:8F
inet addr:182.148.15.238 Bcast:182.148.15.255 Mask:255.255.255.224
inet6 addr: fe80::5054:ff:fe3b:338f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:135305 errors:0 dropped:0 overruns:0 frame:0
TX packets:11256 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:17338566 (16.5 MiB) TX bytes:892363 (871.4 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo:0 Link encap:Local Loopback
inet addr:182.148.15.239 Mask:255.255.255.255
UP LOOPBACK RUNNING MTU:65536 Metric:1
e)配置iptables防火墙
1)后端两台机器MySQL1 Real Server和MySQL2 Real Server要在iptables里开放3306端口
[root@MySQL1 ~]# vim /etc/sysconfig/iptables
......
-A INPUT -m state --state NEW -m tcp -p tcp --dport 3306 -j ACCEPT
[root@MySQL1 ~]# /etc/init.d/iptables restart
2)LVS_Master和LVS_Backup两台机器要在iptables开放VRRP组播地址的相关规则。
注意：这个一定要设置！！！否则会出现故障时的VIP资源漂移错乱问题！
[root@LVS_Master ~]# vim /etc/sysconfig/iptables //两台LVS机器都要设置
.......
-A INPUT -s 182.148.15.0/24 -d 224.0.0.18 -j ACCEPT //允许组播地址通信
-A INPUT -s 182.148.15.0/24 -p vrrp -j ACCEPT //允许VRRP(虚拟路由器冗余协)通信
-A INPUT -m state --state NEW -m tcp -p tcp --dport 3306 -j ACCEPT
[root@LVS_Master ~]# /etc/init.d/iptables restart
3)接着配置LVS+Keepalived配置
1)LVS_Master上的操作
[root@LVS_Master ~]# vim /etc/keepalived/keepalived.conf
! Configuration File for keepalived
global_defs {
router_id LVS_Master
}
vrrp_instance VI_1 {
state MASTER #指定instance初始状态，实际根据优先级决定.backup节点不一样
interface eth0 #虚拟IP所在网
virtual_router_id 51 #VRID，相同VRID为一个组，决定多播MAC地址
priority 100 #优先级，另一台改为90.backup节点不一样
advert_int 1 #检查间隔
authentication {
auth_type PASS #认证方式，可以是pass或ha
auth_pass 1111 #认证密码
}
virtual_ipaddress {
182.148.15.239 #VIP
}
}
virtual_server 182.148.15.239 3306 {
delay_loop 6 #服务轮询的时间间隔
lb_algo wrr #加权轮询调度，LVS调度算法 rr|wrr|lc|wlc|lblc|sh|sh
lb_kind DR #LVS集群模式 NAT|DR|TUN，其中DR模式要求负载均衡器网卡必须有一块与物理网卡在同一个网段
#nat_mask 255.255.255.0
persistence_timeout 50 #会话保持时间
protocol TCP #健康检查协议
## Real Server设置，3306就是MySQL连接端口
real_server 182.148.15.233 3306 {
weight 3 ##权重
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 3306
}
}
real_server 182.148.15.238 3306 {
weight 3
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 3306
}
}
}
启动keepalived
[root@LVS_Master ~]# /etc/init.d/keepalived start
Starting keepalived: [ OK ]
注意此时网卡的变化，可以看到虚拟网卡已经分配到了realserver上。
此时查看LVS集群状态，可以看到集群下有两个Real Server，调度算法，权重等信息。ActiveConn代表当前Real Server的活跃连接数。
[root@LVS_Master ~]# ipvsadm -ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 182.148.15.239:3306 wrr persistent 50
-> 182.148.15.233:3306 Route 3 1 0
-> 182.148.15.238:3306 Route 3 0 0
2)LVS_Backup上的操作
[root@LVS_Backup ~]# vim /etc/keepalived/keepalived.conf
! Configuration File for keepalived
global_defs {
router_id LVS_Backup
}
vrrp_instance VI_1 {
state BACKUP
interface eth0
virtual_router_id 51
priority 90
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
182.148.15.239
}
}
virtual_server 182.148.15.239 3306 {
delay_loop 6
lb_algo wrr
lb_kind DR
persistence_timeout 50
protocol TCP
real_server 182.148.15.233 3306 {
weight 3
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 3306
}
}
real_server 182.148.15.238 3306 {
weight 3
TCP_CHECK {
connect_timeout 3
nb_get_retry 3
delay_before_retry 3
connect_port 3306
}
}
}
启动keepalived
[root@LVS_Backup ~]# /etc/init.d/keepalived start
Starting keepalived: [ OK ]
[root@LVS_Backup ~]# ipvsadm -ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 182.148.15.239:3306 wrr persistent 50
-> 182.148.15.233:3306 Route 3 0 0
-> 182.148.15.238:3306 Route 3 0 0
此时LVS+Keepalived+MySQL主主复制已经搭建完成。
4)最后进行测试验证
1)先进行功能性验证
a)关闭MySQL2 Real Server服务器上的mysql
[root@MySQL2 ~]# /etc/init.d/mysql stop
Shutting down MySQL.. SUCCESS!
在LVS_Master查看/var/log/messages中关于keepalived日志，LVS_Master检测到了MySQL2 Real Server服务器宕机，同时LVS集群自动剔除了故障节点
[root@LVS_Master ~]# tail -f /var/log/messages
.......
Apr 26 15:22:19 test3-237 Keepalived_healthcheckers[4606]: TCP connection to [182.148.15.238]:3306 failed.
Apr 26 15:22:19 test3-237 Keepalived_vrrp[4608]: Sending gratuitous ARP on eth0 for 182.148.15.239
.......
[root@LVS_Master ~]# ipvsadm -ln //LVS已经将MySQL2 Real Server剔除
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 182.148.15.239:3306 wrr persistent 50
-> 182.148.15.233:3306 Route 3 1 0
从新启动MySQL2 Real Server后自动将故障节点自动加入LVS集群
[root@LVS_Master ~]# tail -f /var/log/messages
.......
Apr 26 15:23:49 test3-237 Keepalived_healthcheckers[4606]: TCP connection to [182.148.15.238]:3306 success.
Apr 26 15:23:49 test3-237 Keepalived_healthcheckers[4606]: Adding service [182.148.15.238]:3306 to VS [182.148.15.239]:3306
.......
[root@LVS_Master ~]# ipvsadm -ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 182.148.15.239:3306 wrr persistent 50
-> 182.148.15.233:3306 Route 3 1 0
-> 182.148.15.238:3306 Route 3 1 0
b)关闭LVS_Master上的Keepalived(模拟宕机操作)，查看LVS_Master上的日志，可以看到Keepalived移出了LVS1上的VIP
[root@LVS_Master ~]# /etc/init.d/keepalived stop
Stopping keepalived: [ OK ]
[root@LVS_Master ~]# tail -f /var/log/messages
........
Apr 26 15:29:38 test3-237 Keepalived[4976]: Stopping
Apr 26 15:29:38 test3-237 Keepalived_vrrp[4979]: VRRP_Instance(VI_1) sent 0 priority
Apr 26 15:29:38 test3-237 Keepalived_vrrp[4979]: VRRP_Instance(VI_1) removing protocol VIPs.
Apr 26 15:29:38 test3-237 Keepalived_healthcheckers[4977]: Removing service [182.148.15.233]:3306 from VS [182.148.15.239]:3306
Apr 26 15:29:38 test3-237 Keepalived_healthcheckers[4977]: Removing service [182.148.15.238]:3306 from VS [182.148.15.239]:3306
Apr 26 15:29:38 test3-237 Keepalived_healthcheckers[4977]: Stopped
Apr 26 15:29:38 test3-237 kernel: IPVS: __ip_vs_del_service: enter
Apr 26 15:29:39 test3-237 Keepalived_vrrp[4979]: Stopped
Apr 26 15:29:39 test3-237 Keepalived[4976]: Stopped Keepalived v1.3.5 (03/19,2017), git commit v1.3.5-6-g6fa32f2
[root@LVS_Master ~]# ip addr //发现VIP资源已经不在本机了
1: lo: mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 52:54:00:68:dc:b6 brd ff:ff:ff:ff:ff:ff
inet 182.148.15.237/27 brd 182.148.15.255 scope global eth0
inet 182.148.15.239/27 brd 182.148.15.255 scope global secondary eth0:0
inet6 fe80::5054:ff:fe68:dcb6/64 scope link
valid_lft forever preferred_lft forever
同时查看LVS_Backup上日志，可以看到LVS_Backup成为了Master，并接管了VIP
[root@LVS_Backup ~]# tail -f /var/log/messages
.....
Apr 26 15:26:41 test4-236 Keepalived_vrrp[4711]: VRRP_Instance(VI_1) Transition to MASTER STATE
Apr 26 15:26:42 test4-236 Keepalived_vrrp[4711]: VRRP_Instance(VI_1) Entering MASTER STATE
Apr 26 15:26:42 test4-236 Keepalived_vrrp[4711]: VRRP_Instance(VI_1) setting protocol VIPs.
Apr 26 15:26:42 test4-236 Keepalived_vrrp[4711]: Sending gratuitous ARP on eth0 for 182.148.15.239
Apr 26 15:26:42 test4-236 Keepalived_vrrp[4711]: VRRP_Instance(VI_1) Sending/queueing gratuitous ARPs on eth0 for 182.148.15.239
[root@LVS_Backup ~]# ip addr //发现VIP资源已经转移到LVS_Backup机器上了
1: lo: mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 52:54:00:90:ac:0f brd ff:ff:ff:ff:ff:ff
inet 182.148.15.236/27 brd 182.148.15.255 scope global eth0
inet 182.148.15.239/32 scope global eth0
inet6 fe80::5054:ff:fe90:ac0f/64 scope link
valid_lft forever preferred_lft forever
在LVS_Backup上查看LVS集群状态，一切正常。
[root@LVS_Backup ~]# ipvsadm -ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 182.148.15.239:3306 wrr persistent 50
-> 182.148.15.233:3306 Route 3 0 0
-> 182.148.15.238:3306 Route 3 1 1
接着恢复LVS_Master上的Keepalived，发现VIP资源又会重新从LVS_Backup上转移回来。即LVS_Master重新接管服务。
[root@LVS_Master ~]# tail -f /var/log/messages
.......
Apr 26 15:37:14 test3-237 Keepalived_vrrp[5263]: VRRP_Instance(VI_1) Transition to MASTER STATE
Apr 26 15:37:15 test3-237 Keepalived_vrrp[5263]: VRRP_Instance(VI_1) Entering MASTER STATE
Apr 26 15:37:15 test3-237 Keepalived_vrrp[5263]: VRRP_Instance(VI_1) setting protocol VIPs.
Apr 26 15:37:15 test3-237 Keepalived_vrrp[5263]: Sending gratuitous ARP on eth0 for 182.148.15.239
Apr 26 15:37:15 test3-237 Keepalived_vrrp[5263]: VRRP_Instance(VI_1) Sending/queueing gratuitous ARPs on eth0 for 182.148.15.239
[root@LVS_Master ~]# ip addr
1: lo: mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 52:54:00:68:dc:b6 brd ff:ff:ff:ff:ff:ff
inet 182.148.15.237/27 brd 182.148.15.255 scope global eth0
inet 182.148.15.239/32 scope global eth0
inet 182.148.15.239/27 brd 182.148.15.255 scope global secondary eth0:0
inet6 fe80::5054:ff:fe68:dcb6/64 scope link
valid_lft forever preferred_lft forever
-----------------------------------------------------------------------------------------
2)接着进行mysql主主热备的高可用
在MySQL1 Real Server和MySQL2 Real Server两台机器的mysql里授权，使远程客户机能正常连接。
mysql> grant all on *.* to test@'%' identified by "123456";
Query OK, 0 rows affected (0.03 sec)
mysql> flush privileges;
经测试发现，对于上面的功能验证，不管是LVS_Master的keepalived关闭(宕机)还是后端MySQL2 Real Serve的mysql关闭，在远程客户机上都能正常连接mysql(通过VIP进行连接)(LVS_Master的keepalived关闭时，如若远程客户机在连接mysql中，可以断开重新连接一次即可)
[root@bastion-IDC ~]# mysql -h182.148.15.239 -utest -p123456
Welcome to the MySQL monitor. Commands end with ; or \g.
Your MySQL connection id is 856
Server version: 5.6.34-log Source distribution
Copyright (c) 2000, 2013, Oracle and/or its affiliates. All rights reserved.
Oracle is a registered trademark of Oracle Corporation and/or its
affiliates. Other names may be trademarks of their respective
owners.
Type 'help;' or '\h' for help. Type '\c' to clear the current input statement.
mysql> select * from huanqiu.haha;
+----+-----------+
| id | name |
+----+-----------+
| 1 | wangshibo |
| 2 | guohuihui |
| 22 | huihui |
| 23 | bobo |
+----+-----------+
4 rows in set (0.00 sec)
总结几点：
1)MySQL主主复制是集群的基础，组成Server Array，其中每个节点作为Real Server。
2)LVS服务器提供了负载均衡的作用，将用户请求分发到Real Server，一台Real Server故障并不会影响整个集群的。
3)Keepalived搭建主备LVS服务器，避免了LVS服务器的单点故障，出现故障时可以自动切换到正常的节点。
4)VRRP虚拟IP地址和接口实际IP必须在同一个网段内，VRRP两个实际接口不在同一网段，是不能形成主备关系的。因为：
VRRP的形式是组播(多播)，这个和广播基本一个原理，只不过缩小了范围，让几个服务器能收到，众所周知广播必须在2层里面实现，出3层就出了广播域了。
VRRP中的ip切换是靠arp欺骗实现的，否则vip从主切到备得断多少机器，arp欺骗也是没法在出了3层以外的2个机器直接做的。
427
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
