I210网卡LINUX的mac,linux i210 网卡驱动解读

从最常见的修改mac address 说起：

section 1: 读mac address

/* Only the MAC addr is required to be present in the iNVM */

switch (offset) {

case NVM_MAC_ADDR:

ret_val = igb_read_invm_word_i210(hw, (u8)offset, &data[0]);

ret_val |= igb_read_invm_word_i210(hw, (u8)offset+1,

&data[1]);

ret_val |= igb_read_invm_word_i210(hw, (u8)offset+2,

&data[2]);

if (ret_val)

hw_dbg("MAC Addr not found in iNVM\n");

break;

mac address 是放在eeprom 最开始的位置：

/* NVM Word Offsets */

#define NVM_COMPAT 0x0003

#define NVM_ID_LED_SETTINGS 0x0004 /* SERDES output amplitude */

#define NVM_VERSION 0x0005

#define NVM_INIT_CONTROL2_REG 0x000F

#define NVM_INIT_CONTROL3_PORT_B 0x0014

#define NVM_INIT_CONTROL3_PORT_A 0x0024

#define NVM_ALT_MAC_ADDR_PTR 0x0037

#define NVM_CHECKSUM_REG 0x003F

#define NVM_COMPATIBILITY_REG_3 0x0003

#define NVM_COMPATIBILITY_BIT_MASK 0x8000

#define NVM_MAC_ADDR 0x0000

#define NVM_SUB_DEV_ID 0x000B

#define NVM_SUB_VEN_ID 0x000C

#define NVM_DEV_ID 0x000D

#define NVM_VEN_ID 0x000E

#define NVM_INIT_CTRL_2 0x000F

#define NVM_INIT_CTRL_4 0x0013

#define NVM_LED_1_CFG 0x001C

#define NVM_LED_0_2_CFG 0x001F

#define NVM_ETRACK_WORD 0x0042

#define NVM_ETRACK_HIWORD 0x0043

#define NVM_COMB_VER_OFF 0x0083

#define NVM_COMB_VER_PTR 0x003d

/**

* igb_set_mac - Change the Ethernet Address of the NIC

* @netdev: network interface device structure

* @p: pointer to an address structure

*

* Returns 0 on success, negative on failure

**/

static int igb_set_mac(struct net_device *netdev, void *p)

{

struct igb_adapter *adapter = netdev_priv(netdev);

struct e1000_hw *hw = &adapter->hw;

struct sockaddr *addr = p;

if (!is_valid_ether_addr(addr->sa_data))

return -EADDRNOTAVAIL;

memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);

memcpy(hw->mac.addr, addr->sa_data, netdev->addr_len);

/* set the correct pool for the new PF MAC address in entry 0 */

igb_rar_set_qsel(adapter, hw->mac.addr, 0,

adapter->vfs_allocated_count);

return 0;

}

在最开始，我们的检测这块网卡的flash是否存在：

/**

* igb_get_flash_presence_i210 - Check if flash device is detected.

* @hw: pointer to the HW structure

*

**/

bool igb_get_flash_presence_i210(struct e1000_hw *hw)

{

u32 eec = 0;

bool ret_val = false;

eec = rd32(E1000_EECD);

if (eec & E1000_EECD_FLASH_DETECTED_I210)

ret_val = true;

return ret_val;

}

rd32定义在 e1000_regs.h里面

#define rd32(reg) (igb_rd32(hw, reg))

u32 igb_rd32(struct e1000_hw *hw, u32 reg);

其函数实现在igb_main.c

u32 igb_rd32(struct e1000_hw *hw, u32 reg)

{

struct igb_adapter *igb = container_of(hw, struct igb_adapter, hw);

u8 __iomem *hw_addr = ACCESS_ONCE(hw->hw_addr);

u32 value = 0;

if (E1000_REMOVED(hw_addr))

return ~value;

value = readl(&hw_addr[reg]);

/* reads should not return all F's */

if (!(~value) && (!reg || !(~readl(hw_addr)))) {

struct net_device *netdev = igb->netdev;

hw->hw_addr = NULL;

netif_device_detach(netdev);

netdev_err(netdev, "PCIe link lost, device now detached\n");

}

return value;

}

如何通过pcd 配置空间读到mac address ?

那我们就来到9.3.11