查看现在设置的多少tcp连接:ulimit -n //如果是65535,已经最大
如果还是不够用,修改配置文件
vi /etc/sysctl.conf
添加
net.ipv4.ip_conntrack_max = 65534
1. 调低端口释放后的等待时间, 默认为60s, 修改为15~30s
echo 30 > /proc/sys/net/ipv4/tcp_fin_timeout
2. 修改tcp/ip协议配置, 通过配置/proc/sys/net/ipv4/tcp_tw_resue, 默认为0, 修改为1, 释放TIME_WAIT端口给新连接使用。
echo 1 > /proc/sys/net/ipv4/tcp_tw_reuse
3. 修改tcp/ip协议配置,快速回收socket资源, 默认为0, 修改为1.
echo 1 > /proc/sys/net/ipv4/tcp_tw_recycle
也可以在vi /etc/sysctl.conf里修改
sysctl -p //马上生效
以下转自:http://willvvv.iteye.com/blog/1558321
1.Linux系统设置优化,vi /etc/sysctl.conf,添加以下内容
fs.file-max = 65535
kernel.pid_max = 65536
net.ipv4.tcp_syncookies = 1
net.ipv4.tcp_synack_retries = 2
net.ipv4.tcp_syn_retries = 2
net.ipv4.tcp_timestsmps = 0
net.ipv4.tcp_tw_reuse = 1
net.ipv4.tcp_tw_recycle = 1
net.ipv4.tcp_fin_timeout = 30
net.ipv4.tcp_keepalive_time = 1200
net.ipv4.ip_local_port_range = 10000 65535
net.ipv4.tcp_max_syn_backlog = 8192
net.ipv4.tcp_max_tw_buckets = 5000
net.ipv4.tcp_wmem = 8192 436600 873200
net.ipv4.tcp_rmem = 32768 436600 873200
net.ipv4.tcp_mem = 94500000 91500000 92700000
net.ipv4.tcp_max_orphans = 3276800
net.core.netdev_max_backlog = 32768
net.core.somaxconn = 32768
net.core.wmem_default = 8388608
net.core.rmem_default = 8388608
net.core.rmem_max = 16777216
net.core.wmem_max = 16777216
保存后:
sysctl -p /etc/sysctl.conf // 作用:重新载入/etc/sysctl.conf文件
相关参数说明如下:
# TCP and memory optimization
# increase TCP max buffer size setable using setsockopt()
#it's already auto-tuned very well by Linux based on the amount of RAM.
#net.ipv4.tcp_mem = 94500000 915000000 927000000
net.ipv4.tcp_rmem = 4096 87380 8388608
net.ipv4.tcp_wmem = 4096 87380 8388608
net.ipv4.tcp_max_orphans = 3276800
net.ipv4.tcp_timestamps = 1
net.ipv4.tcp_synack_retries = 2
net.ipv4.tcp_syn_retries = 2
#表示SYN队列的长度,默认为1024,加大队列长度为8192,可以容纳更多等待连接的网络连接数。
net.ipv4.tcp_max_syn_backlog = 65536
#表示开启SYN Cookies。当出现SYN等待队列溢出时,启用cookies来处理,可防范少量SYN***,默认为0,表示关闭;
net.ipv4.tcp_syncookies = 1
#表示开启重用。允许将TIME-WAIT sockets重新用于新的TCP连接,默认为0,表示关闭;
net.ipv4.tcp_tw_reuse = 1
#表示开启TCP连接中TIME-WAIT sockets的快速回收,默认为0,表示关闭;
net.ipv4.tcp_tw_recycle = 1
#修改系統默认的 TIMEOUT 时间。
net.ipv4.tcp_fin_timeout = 30
#表示当keepalive起用的时候,TCP发送keepalive消息的频度。缺省是2小时,改为20分钟。
net.ipv4.tcp_keepalive_time = 1200
#表示用于向外连接的端口范围。缺省情况下很小:32768到61000,改为10000到65000。(注意:这里不要将最低值设的太低,否则可能会占用掉正常的端口!)
net.ipv4.ip_local_port_range = 10000 65000
#表示系统同时保持TIME_WAIT的最大数量,如果超过这个数字,TIME_WAIT将立刻被清除并打印警告信息。默 认为180000,改为6000。对于Apache、Nginx等服务器,上几行的参数可以很好地减少TIME_WAIT套接字数量,但是对于 Squid,效果却不大。此项参数可以控制TIME_WAIT的最大数量,避免Squid服务器被大量的TIME_WAIT拖死。
net.ipv4.tcp_max_tw_buckets = 6000
2.修改操作系统的ulimit 限制,vi /etc/security/ ,增加如下两行(具体数值大点小点问题不大):
* soft nofile 65535
* hard nofile 65535
转载于:https://blog.51cto.com/7539178/1971143