1.Refer to the exhibit. A junior network engineer has prepared the exhibited configuration file. What two statements are true of the planned configuration for interface fa0/1? (Choose two.)<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" />

A.The two FastEthernet interfaces will require NAT configured . two outside serial interfaces.
B.Address translation . fa0/1 is not required for DMZ Devices to access the Internet.
C.The fa0/1 IP address overlaps with the space used by s0/0.
D.The fa0/1 IP address is invalid for the IP subnet . which it resides.
E.Internet hosts may not initiate connections to DMZ Devices through the configuration that is shown.
Correct:B E
2.Refer to the exhibit. Which statement describes DLCI 17?

A.DLCI 17 describes the ISDN circuit between R2 and R3.
B.DLCI 17 describes a PVC . R2. It cannot be used . R3 or R1.
C.DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
D.DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.
Correct:C
3.What is the default Local Management Interface frame type transmitted by a Cisco router . a Frame Relay circuit?
A.Q<?xml:namespace prefix = st1 ns = "urn:schemas-microsoft-com:office:smarttags" />933a
B.B8ZS
C.IETF
D.Cisco
E.ANSI
Correct:D
4.Refer to the exhibit. The network shown in the exhibit has just been installed. Host B can access the Internet, but it is unable to ping host C. What is the problem with this configuration?

A.Host B should be in VLAN 13.
B.The address of host C is incorrect.
C.The gateway for host B is in a different subnet than the host is ..
D.The switch port that sends VLAN 13 frames from the switch to the router is shut down.
E.The switch port connected to the router is incorrectly configured as an access port.
Correct:B
5.Drop

Correct:
Green choice1---->Yellow Choice5
Green choice2---->Yellow Choice3
Green choice3---->Yellow Choice1
Green choice4---->Yellow Choice6
Green choice5---->Yellow Choice4
Green choice6---->Yellow Choice2
6.Refer to the exhibit. The router has been configured with these commands: hostname Gateway interface FastEthernet 0/0 ip address 198.133.219.14 255.255.255.248 no shutdown interface FastEthernet 0/1 ip address 192.168.10.254 255.255.255.0 no shutdown interface Serial 0/0 ip address 64.100.0.2 255.255.255.252 no shutdown ip route 0.0.0.0 0.0.0.0 64.100.0.1 What are the two results of this configuration? (Choose two.)

A.The default route should have a next hop address of 64.100.0.3.
B.Hosts . the LAN that is connected to FastEthernet 0/1 are using public IP addressing.
C.The address of the subnet segment with the WWW server will support seven more servers.
D.The addressing scheme allows users . the Internet to access the WWW server.
E.Hosts . the LAN that is connected to FastEthernet 0/1 will not be able to access the Internet without address translation.
Correct:D E
7.Hotspot

Correct:
8.Refer to the exhibit. Two routers have just been configured by a new technician. All interfaces are up. However, the routers are not sharing their routing tables. What is the problem?

A.Split horizon is preventing Router2 from receiving routing information from Router1.
B.Router1 is configured for RIP version 2, and Router2 is configured for RIP version 1.
C.Router1 has an ACL that is blocking RIP version 2.
D.There is a physical connectivity problem between Router1 and Router2.
E.Router1 is using authentication and Router2 is not.
Correct:B
9.Refer to the exhibit. What can be concluded from the output of the debug command?

A.The output represents normal OSPF operation.
B.The interfaces of two OSPF routers connected to the Border router are in the same subnet.
C.The OSPF router connected to interface Serial0/1 has NOT formed a neighbor relationship with the Border router.
D.A router is connected to interface Serial0/3 of the Border router. The OSPF router ID of the connected router is the IP address of the connected interface.
Correct:C
10.Refer to the output from the show running-config command in the exhibit. What should the administrator do to allow the workstations connected to the FastEthernet 0/0 interface to obtain an IP address?

A.Apply access-group 14 to interface FastEthernet 0/0.
B.Add access-list 14 permit any any to the access list configuration.
C.Configure the IP address of the FastEtherent 0/0 interface to 10.90.201.1.
D.Add an interface de.ion to the FastEthernet 0/0 interface configuration.
Correct:C
11.S0/0 . R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIP v2 in place of the static routes?

A.Configure the no ip subnet-zero command . R1, R2, and R3.
B.Dynamic routing protocols such as RIP v2 cannot be used across Frame Relay networks.
C.Configure the s0/0 interface . R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E.Change the network address configurations to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetworks.
Correct:C
12.Refer to the exhibit. HostA cannot ping HostB. Assuming routing is properly configured, what could be the cause of this problem?

A.HostA is not . the same subnet as its default gateway.
B.The address of SwitchA is a subnet address.
C.The Fa0/0 interface . RouterA is . a subnet that can't be used.
D.The serial interfaces of the routers are not . the same subnet.
E.The Fa0/0 interface . RouterB is using a broadcast address.
Correct:D
13.Refer to the exhibit. The routers are running RIPv2. Which addressing scheme would satisfy the needs of this network yet waste the fewest addresses?

A.Network 1: 192.168.10.0/26 Network 2: 192.168.10.64/26 Network 3: 192.168.10.128/26 Serial link 1: 192.168.20.0/24 Serial link 2: 192.168.30.0/24
B.Network 1: 192.168.10.0/26 Network 2: 192.168.10.64/28 Network 3: 192.168.10.80/29 Serial link 1: 192.168.10.88/30 Serial link 2: 192.168.10.96/30
C.Network 1: 192.168.10.0/26 Network 2: 192.168.10.64/27 Network 3: 192.168.10.96/28 Serial link 1: 192.168.10.112/30 Serial link 2: 192.168.10.116/30
D.Network 1: 192.168.10.0/27 Network 2: 192.168.10.64/28 Network 3: 192.168.10.96/29 Serial link 1: 192.168.10.112/30 Serial link 2: 192.168.10.116/30
Correct:C
14.Refer to the exhibit. At the end of an RSTP election process, which access layer switch port will assume the discarding role?

A.Switch3, port fa0/1
B.Switch3, port fa0/12
C.Switch4, port fa0/11
D.Switch4, port fa0/2
E.Switch3, port Gi0/1
F.Switch3, port Gi0/2
Correct:C
15.Refer to the exhibit. The Lakeside Company has the internetwork in the exhibit. The administrator would like to reduce the size of the routing table . the Central router. Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets?

A.10.0.0 .0/22 is subnetted, 1 subnets D10.0.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
B.10.0.0.0/28 is subnetted, 1 subnets D10.2.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
C.10.0.0.0/30 is subnetted, 1 subnets D10.2.2.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
D.10.0.0.0/22 is subnetted, 1 subnets D10.4.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
E.10.0.0.0/28 is subnetted, 1 subnets D10.4.4.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
F.10.0.0.0/30 is subnetted, 1 subnets D 10.4.4.4 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
Correct:D
16.Refer to the exhibit. What does STATUS=ACTIVE refer to in the output of the show frame-relay pvc command?

A.The PVC is experiencing congestion.
B.The Frame Relay switch is correctly programmed with the DLCI and is operational.
C.The router is actively broadcasting to establish a link to the Frame Relay switch.
D.The router is connected to the local Frame Relay switch, but not to the far end device.
Correct:B
17.The network administrator of the Oregon router adds the following command to the router configuration: ip route 192.168.12.0 255.255.255.0 172.16.12.1. What are the results of adding this command? (Choose two.)

A.The command establishes a static route.
B.The command invokes a dynamic routing protocol for 192.168.12.0.
C.Traffic for network 192.168.12.0 is forwarded to 172.16.12.1.
D.Traffic for all networks is forwarded to 172.16.12.1.
E.This route is automatically propagated throughout the entire network.
F.Traffic for network 172.16.12.0 is forwarded to the 192.168.12.0 network.
Correct:A C
18.Refer to the graphic. Users . the Holyoke router are unable to access the intranet server attached to interface E0 of the Chicopee router. Inspection of the routing table of the Holyoke router shows that an entry for the Chicopee E0 network is missing. Which command will configure the Holyoke router with a path to the intranet server network?

A.Holyoke(config)# ip host Chicopee 201.73.127.2
B.Holyoke(config)# ip host Chicopee 201.73.127.0 255.255.255.0
C.Holyoke(config)# ip network 202.18.38.0
D.Holyoke(config)# ip network 202.18.18.0 255.255.255.0
E.Holyoke(config)# ip route 202.18.18.0 255.255.255.0 201.73.127.2
F.Holyoke(config)# ip route 201.73.127.2 255.255.255.0 202.18.18.0
Correct:E
19.A network administrator would like to implement NAT in the network shown in the graphic to allow inside hosts to use a private addressing scheme. Where should NAT be configured?

A.Corporate router
B.Engineering router
C.Sales router
D.all routers
E.all routers and switches
Correct:A
20.Drop

Correct:
Green choice2---->Yellow Choice1
Green choice4---->Yellow Choice2
Green choice5---->Yellow Choice3
Green choice1---->Yellow Choice4
21.A network administrator must configure 200 switch ports to accept traffic from .ly the currently attached host devices. What would be the most efficient way to configure MAC-level security . all these ports?
A.Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command.
B.Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command.
C.Use the switchport port-security MAC address sticky command . all the switch ports that have end devices connected to them.
D.Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands . each switch for MAC address port-security.
Correct:C
22.LAB

A.Router>enable Router#config terminal Router(config)#hostname weaver weaver(config)#ip nat pool test 198.18.191.145 198.18.191.150 255.255.255.248 weaver(config)#ip nat inside source list 1 pool test overload weaver(config)#access-list 1 permit 192.168.108.32 0.0.0.31 weaver(config)#interface fa0/0 weaver(config-if)#ip address 192.168.108.62 255.255.255.224 weaver(config-if)#ip nat inside weaver(config-if)#interface s0/0 weaver(config-if)#ip nat outside
Correct:A
23.In which circumstance are multiple copies of the same unicast frame likely to be transmitted in a switched LAN?
A.during high traffic periods
B.after broken links are re-established
C.when upper-layer protocols require high reliability
D.in an improperly implemented redundant topology
E.when a dual ring topology is in use
Correct:D
24.Which PPP subprotocol negotiates authentication options?
A.NCP
B.ISDN
C.SLIP
D.LCP
E.DLCI
Correct:D
25.A network administrator is configuring the routers in the graphic for OSPF. The OSPF process has been started and the networks have been configured for Area 0 as shown in the diagram. The network administrator has several options for configuring RouterB to ensure that it will be preferred as the designated router (DR) for the 172.16.1.0 /24 LAN segment. What configuration tasks could be used to establish this preference? (Choose three.)

A.Configure the priority value of the Fa0/0 interface of RouterB to a higher value than any other interface . the Ethernet network.
B.Change the router id of Router B by assigning the IP address 172.16.1.130/24 to the Fa0/0 interface of RouterB.
C.Configure a loopback interface . RouterB with an IP address higher than any IP address . the other routers.
D.Change the priority value of the Fa0/0 interface of RouterB to zero.
E.Change the priority values of the Fa0/0 interfaces of RouterA and RouterC to zero.
F.No further configuration is necessary.
Correct:A C E
26.Which statements are true about EIGRP successor routes? (Choose two.)
A.A successor route is used by EIGRP to forward traffic to a destination.
B.Successor routes are saved in the topology table to be used if the primary route fails.
C.Successor routes are flagged as "active" in the routing table.
D.A successor route may be backed up by a feasible successor route.
E.Successor routes are stored in the neighbor table following the discovery process.
Correct:A D
27.When are packets processed by an inbound access list?
A.before they are routed to an outbound interface
B.after they are routed to an outbound interface
C.before and after they are routed to an outbound interface
D.after they are routed to an outbound interface but before being placed in the outbound queue
Correct:A
28.The company internetwork is subnetted using 29 bits. Which wildcard mask should be used to configure an extended access list to permit or deny access to an entire subnetwork?
A.255.255.255.224
B.255.255.255.248
C.0.0.0.224
D.0.0.0.8
E.0.0.0.7
F.0.0.0.3
Correct:E
29.A router has been configured to provide the nine users . the branch office LAN with Internet access, as shown in the diagram. It is found that some of the users . the LAN cannot reach the Internet. Based . the topology and router output shown, which command should be issued . the router to correct the problem?

A.Branch(config-if)# no shutdown
B.Branch(config-if)# duplex full
C.Branch(config-if)# no keepalive
D.Branch(config-if)# ip address 192.168.10.30 255.255.255.240
E.Branch(config-if)# bandwidth 100
F.Branch(config-if)# encapsulation 802.3
Correct:D
30.What are three valid reasons to assign ports to VLANs . a switch? (Choose three.)
A.to make VTP easier to implement
B.to isolate broadcast traffic
C.to increase the size of the collision domain
D.to allow more devices to connect to the network
E.to logically group hosts according to function
F.to increase network security
Correct:B E F