https://iperf.fr
[root@wallet01 ~]# tar zxvf iperf-3.1.3-source.tar.gz
[root@wallet01 ~]# cd iperf-3.1.3
[root@wallet01 iperf-3.1.3]# ./configure
[root@wallet01 iperf-3.1.3]# make
[root@wallet01 iperf-3.1.3]# make install
[root@wallet01 ~]# iperf3 --help
Usage: iperf [-s|-c host] [options]
iperf [-h|--help] [-v|--version]
Server or Client:
-p, --port # server port to listen on/connect to
-f, --format [kmgKMG] format to report: Kbits, Mbits, KBytes, MBytes
-i, --interval # seconds between periodic bandwidth reports
-F, --file name xmit/recv the specified file
-A, --affinity n/n,m set CPU affinity
-B, --bind <host> bind to a specific interface
-V, --verbose more detailed output
-J, --json output in JSON format
--logfile f send output to a log file
-d, --debug emit debugging output
-v, --version show version information and quit
-h, --help show this message and quit
Server specific:
-s, --server run in server mode
-D, --daemon run the server as a daemon
-I, --pidfile file write PID file
-1, --one-off handle one client connection then exit
Client specific:
-c, --client <host> run in client mode, connecting to <host>
-u, --udp use UDP rather than TCP
-b, --bandwidth #[KMG][/#] target bandwidth in bits/sec (0 for unlimited)
(default 1 Mbit/sec for UDP, unlimited for TCP)
(optional slash and packet count for burst mode)
-t, --time # time in seconds to transmit for (default 10 secs)
-n, --bytes #[KMG] number of bytes to transmit (instead of -t)
-k, --blockcount #[KMG] number of blocks (packets) to transmit (instead of -t or -n)
-l, --len #[KMG] length of buffer to read or write
(default 128 KB for TCP, 8 KB for UDP)
--cport <port> bind to a specific client port (TCP and UDP, default: ephemeral port)
-P, --parallel # number of parallel client streams to run
-R, --reverse run in reverse mode (server sends, client receives)
-w, --window #[KMG] set window size / socket buffer size
-C, --congestion <algo> set TCP congestion control algorithm (Linux and FreeBSD only)
-M, --set-mss # set TCP/SCTP maximum segment size (MTU - 40 bytes)
-N, --no-delay set TCP/SCTP no delay, disabling Nagle's Algorithm
-4, --version4 only use IPv4
-6, --version6 only use IPv6
-S, --tos N set the IP 'type of service'
-L, --flowlabel N set the IPv6 flow label (only supported on Linux)
-Z, --zerocopy use a 'zero copy' method of sending data
-O, --omit N omit the first n seconds
-T, --title str prefix every output line with this string
--get-server-output get results from server
--udp-counters-64bit use 64-bit counters in UDP test packets
[KMG] indicates options that support a K/M/G suffix for kilo-, mega-, or giga-
[root@wallet01 ~]# perf3 -s -D
[root@wallet01 ~]# netstat -tunlp | grep iperf
tcp 0 0 :::5201 :::* LISTEN 28691/iperf3
[root@wallet02 ~]# iperf3 -c 192.168.40.34 -f MBytes
Connecting to host 192.168.40.34, port 5201
[ 4] local 192.168.30.32 port 39074 connected to 192.168.40.34 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.00 sec 12.3 MBytes 12.3 MBytes/sec 124 229 KBytes
[ 4] 1.00-2.00 sec 11.2 MBytes 11.2 MBytes/sec 0 243 KBytes
[ 4] 2.00-3.00 sec 11.2 MBytes 11.2 MBytes/sec 0 259 KBytes
[ 4] 3.00-4.00 sec 11.2 MBytes 11.2 MBytes/sec 1 209 KBytes
[ 4] 4.00-5.00 sec 11.2 MBytes 11.2 MBytes/sec 0 238 KBytes
[ 4] 5.00-6.00 sec 11.2 MBytes 11.2 MBytes/sec 0 255 KBytes
[ 4] 6.00-7.00 sec 11.2 MBytes 11.2 MBytes/sec 0 263 KBytes
[ 4] 7.00-8.00 sec 11.2 MBytes 11.2 MBytes/sec 0 266 KBytes
[ 4] 8.00-9.00 sec 11.2 MBytes 11.2 MBytes/sec 3 221 KBytes
[ 4] 9.00-10.00 sec 11.2 MBytes 11.2 MBytes/sec 0 245 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 113 MBytes 11.3 MBytes/sec 128 sender
[ 4] 0.00-10.00 sec 112 MBytes 11.2 MBytes/sec receiver
iperf Done.
转载于:https://blog.51cto.com/13598811/2341566