利用多层交换机实现不同VLAN之间的通信

最新推荐文章于 2024-04-18 16:09:04 发布

weixin_34082695

最新推荐文章于 2024-04-18 16:09:04 发布

阅读量603

点赞数

原文链接：http://blog.51cto.com/13399304/1972983

版权

实验图片在附件里面

基本配置

PC1 IP:192.168.1.1 子网掩码：255.255.255.0 网关：162.168.1.254

PC2 IP:192.168.2.1 子网掩码：255.255.255.0 网关：162.168.2.254

PC3 IP:192.168.3.1 子网掩码：255.255.255.0 网关：162.168.3.254

还需要一台二层交换机SW1以及三层交换机SW2

PC1的端口与交换机SW1端口f0/2相连接，PC2的端口与交换机SW1端口f0/3相连接，

PC3的端口与交换机SW1端口f0/4相连接，交换机SW1端口f0/1与三层交换机f0/1端口

相连接。

之后进行设备的命令配置

配置交换机SW1

Switch>enable //切换模式

Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname SW1 //修改主机名
SW1(config)#vlan 10 //创建VLAN
SW1(config-vlan)#vlan 20
SW1(config-vlan)#vlan 30
SW1(config-vlan)#exit //退出
SW1(config)#interface fastEthernet 0/2 //进入端口
SW1(config-if)#switchport mode access //将端口模式改为access
SW1(config-if)#switchport access vlan 10 //将端口f0/2加入VLAN10
SW1(config-if)#exit
SW1(config)#interface fastEthernet 0/3
SW1(config-if)#switchport mode access
SW1(config-if)#switchport access vlan 20
SW1(config-if)#no shutdown
SW1(config-if)#exit
SW1(config)#interface fastEthernet 0/4
SW1(config-if)#switchport mode access
SW1(config-if)#switchport access vlan 30
SW1(config-if)#no shutdown
SW1(config-if)#eixt
SW1(config)#exit
SW1#
%SYS-5-CONFIG_I: Configured from console by console

SW1#show vlan //查看VLAN

VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gig0/1, Gig0/2
10 VLAN0010 active Fa0/2
20 VLAN0020 active Fa0/3
30 VLAN0030 active Fa0/4
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup

VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0

Remote SPAN VLANs
------------------------------------------------------------------------------

Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------

进入三层交换机SW2进行命令配置

Switch>enable
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#hostname SW2
SW2(config)#vlan 10
SW2(config-vlan)#vlan 20
SW2(config-vlan)#vlan 30
SW2(config-vlan)#exit
SW2(config)#ip routing //开启路由功能
SW2(config)#interface vlan 10 //进入虚拟局域网
SW2(config-if)#
%LINK-5-CHANGED: Interface Vlan10, changed state to up
SW2(config-if)#ip address 192.168.1.254 255.255.255.0 //进行IP配置与PC网关相同
SW2(config-if)#no shutdown //打开端口
SW2(config-if)#exit
SW2(config)#interface vlan 20
SW2(config-if)#
%LINK-5-CHANGED: Interface Vlan20, changed state to up
SW2(config-if)#ip address 192.168.2.254 255.255.255.0
SW2(config-if)#no shutdown
SW2(config-if)#exit
SW2(config)#inter
SW2(config)#interface vlan 30
SW2(config-if)#
%LINK-5-CHANGED: Interface Vlan30, changed state to up
SW2(config-if)#ip address 192.168.3.254 255.255.255.0
SW2(config-if)#no shutdown
SW2(config-if)#exit
SW2(config)#interface f0/1
SW2(config-if)#switchport trunk encapsulation dot1q //修改三层交换机的封装格式
SW2(config-if)#switchport mode trunk //将端口f0/1模式改为trunk
SW2(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan30, changed state to up

SW2(config-if)#end
SW2#
%SYS-5-CONFIG_I: Configured from console by console

SW2#show interfaces trunk //查看trunk信息
Port Mode Encapsulation Status Native vlan
Fa0/1 on 802.1q trunking 1

Port Vlans allowed on trunk
Fa0/1 1-1005

Port Vlans allowed and active in management domain
Fa0/1 1,10,20,30

Port Vlans in spanning tree forwarding state and not pruned
Fa0/1 1,10,20,30
Switch#show inter
Switch#show interfaces vlan
% Incomplete command.
SW2#show vlan

VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
Fa0/14, Fa0/15, Fa0/16, Fa0/17
Fa0/18, Fa0/19, Fa0/20, Fa0/21
Fa0/22, Fa0/23, Fa0/24, Gig0/1
Gig0/2
10 VLAN0010 active
20 VLAN0020 active
30 VLAN0030 active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup

VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0

Remote SPAN VLANs
------------------------------------------------------------------------------

Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
SW2#
SW2#show ip route //查看路由表
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route

Gateway of last resort is not set

C 192.168.1.0/24 is directly connected, Vlan10
C 192.168.2.0/24 is directly connected, Vlan20
C 192.168.3.0/24 is directly connected, Vlan30
Switch#

实验结果

PC>ping 192.168.2.1

Pinging 192.168.2.1 with 32 bytes of data:

Request timed out.
Reply from 192.168.2.1: bytes=32 time=1ms TTL=127
Reply from 192.168.2.1: bytes=32 time=0ms TTL=127
Reply from 192.168.2.1: bytes=32 time=0ms TTL=127

Ping statistics for 192.168.2.1:
Packets: Sent = 4, Received = 3, Lost = 1 (25% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 1ms, Average = 0ms

PC>ping 192.168.3.1

Pinging 192.168.3.1 with 32 bytes of data:

Request timed out.
Reply from 192.168.3.1: bytes=32 time=0ms TTL=127
Reply from 192.168.3.1: bytes=32 time=0ms TTL=127
Reply from 192.168.3.1: bytes=32 time=0ms TTL=127

Ping statistics for 192.168.3.1:
Packets: Sent = 4, Received = 3, Lost = 1 (25% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms