关于交换机清空配置，闲来没事儿自己在总结一下。

Switch#erase startup-config


清除VLAN配置

Switch#delete vlan.dat

这是基本命令，下边是在交换机中显示的信息。

－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－

SW-1#erase startup-config
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
SW-1#
*Mar  1 01:34:46.041: %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram
SW-1#delete vlan.dat
Delete filename [vlan.dat]?
Delete flash:vlan.dat? [confirm]
SW-1#
SW-1#
SW-1#
SW-1#sh vlan br

VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4
                                                Fa0/5, Fa0/6, Fa0/7, Fa0/8
                                                Fa0/9, Fa0/10, Fa0/11, Fa0/12
                                                Fa0/13, Fa0/14, Fa0/15, Fa0/16
                                                Fa0/17, Fa0/18, Fa0/19, Fa0/21
                                                Fa0/23, Fa0/24, Fa0/25, Fa0/26
                                                Fa0/27, Fa0/28, Fa0/29, Fa0/30
                                                Fa0/31, Fa0/32, Fa0/33, Fa0/34
                                                Fa0/35, Fa0/36, Fa0/37, Fa0/38
                                                Fa0/39, Fa0/40, Fa0/41, Fa0/42
                                                Fa0/43, Fa0/44, Fa0/45, Fa0/46
                                                Fa0/47, Fa0/48, Gi0/1, Gi0/2
2    VLAN0002                         active   
3    VLAN0003                         active   
4    VLAN0004                         active   
5    VLAN0005                         active   
10   VLAN0010                         active   
1002 fddi-default                     act/unsup
1003 token-ring-default               act/unsup
1004 fddinet-default                  act/unsup
1005 trnet-default                    act/unsup
SW-1#
SW-1#
SW-1#
SW-1#
SW-1#
SW-1#
SW-1#
SW-1#
SW-1#
SW-1#
SW-1#
SW-1#
SW-1#reload
Proceed with reload? [confirm]

*Mar  1 01:35:20.174: %SYS-5-RELOAD: Reload requested by console. Reload reason: Reload command
Boot Sector Filesystem (bs) installed, fsid: 2
Base ethernet MAC Address: 00:22:0c:6a:fa:00
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
flashfs[0]: 528 files, 19 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32514048
flashfs[0]: Bytes used: 25319424
flashfs[0]: Bytes available: 7194624
flashfs[0]: flashfs fsck took 23 seconds.
...done Initializing Flash.
done.
Loading "flash:/c2960-lanbasek9-mz.122-55.SE4.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@