OSPF实验3：OSPF over NBMA下的五种网络类型

实验等级： Professional

 

实验拓扑：

 

实验基本配置：
1.       首先将R1配置成为帧中继交换机：
frame-relay switching
!
interface Serial1/0
 no ip address
 encapsulation frame-relay
 clock rate 64000
 frame-relay lmi-type ansi
 frame-relay intf-type dce
 frame-relay route 101 interface Serial1/1 102
!
interface Serial1/1
 no ip address
 encapsulation frame-relay
 clock rate 64000
 frame-relay lmi-type ansi
 frame-relay intf-type dce
     frame-relay route 102 interface Serial1/0 101
2.       R2和R3的基本配置：

 

R2：
interface Loopback0
 ip address 2.2.2.2 255.255.255.0
!        
interface Serial1/0
 ip address 12.1.1.2 255.255.255.0
 encapsulation frame-relay
 serial restart-delay 0
 frame-relay map ip 12.1.1.3 101 broadcast
 no frame-relay inverse-arp
!
router ospf 10
 router-id 2.2.2.2
 log-adjacency-changes
 network 2.2.2.0 0.0.0.255 area 0
 network 12.1.1.0 0.0.0.255 area 0

 

R3：
interface Loopback0
 ip address 3.3.3.3 255.255.255.0
!
interface Serial1/1
 ip address 12.1.1.3 255.255.255.0
 encapsulation frame-relay
 serial restart-delay 0
 frame-relay map ip 12.1.1.2 102 broadcast
 no frame-relay inverse-arp
!
router ospf 10
 router-id 3.3.3.3
 log-adjacency-changes
 network 3.3.3.0 0.0.0.255 area 0
     network 12.1.1.0 0.0.0.255 area 0

Type1----Non_Broadcast（默认）

 

我们在R2上show ip ospf neighbor，发现没有邻居。说明在这种情况下邻居需要手动配置！配置如下：

R2：

  R2(config)#router ospf 10

R2(config-router)#neighbor 12.1.1.3

R3：

R3(config)#router ospf 10

R3(config-router)#neighbor 12.1.1.2

此时在R2上查看邻居：

R2#sho ip ospf nei

 

Neighbor ID     Pri   State           Dead Time   Address         Interface

3.3.3.3           1   FULL/DR         00:01:46    12.1.1.3        Serial1/0

发现邻居已经形成并且有DR与BDR的选举！

在R2上查看接口

R2#show ip ospf interface

Serial1/0 is up, line protocol is up

  Internet Address 12.1.1.2/24, Area 0

  Process ID 10, Router ID 2.2.2.2, Network Type NON_BROADCAST, Cost: 64

  Transmit Delay is 1 sec, State BDR, Priority 1

  Designated Router (ID) 3.3.3.3, Interface address 12.1.1.3

  Backup Designated router (ID) 2.2.2.2, Interface address 12.1.1.2

  Flush timer for old DR LSA due in 00:01:40

  Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5

在这种网络类型中，hello的间隔是30s。

打开debug信息，我们可以看到在这种网络类型中，OSPF的数据包是单播传送的。

R2#

*Aug 14 14:52:52.819: OSPF: Send hello to 12.1.1.3 area 0 on Serial1/0 from 12.1.1.2

R2#

*Aug 14 14:52:57.087: OSPF: Rcv hello from 3.3.3.3 area 0 from Serial1/0 12.1.1.3

*Aug 14 14:52:57.091: OSPF: End of hello processing

Type2---- Broadcast

首先去掉刚才手动配置的邻居关系：
R2(config)#router ospf 10
R2(config-router)#no neighbor 12.1.1.3 
R3(config)#router ospf 10
R3(config-router)#no neighbor 12.1.1.2
将R2和R3接口的网络类型改成broadcast
R2(config-router)#int s1/0
R2(config-if)#ip ospf network broadcast
R3(config-router)#int s1/1
R3(config-if)#ip ospf network broadcast
一会我们就看到了如下信息
R3#
*Aug 14 14:59:52.823: %OSPF-5-ADJCHG: Process 10, Nbr 2.2.2.2 on Serial1/1 from LOADING to FULL, Loading Done

这说明了在这种网络类型下是不需要手动配置邻居关系的！

R2#show ip ospf nei

 

Neighbor ID     Pri   State           Dead Time   Address         Interface

3.3.3.3           1   FULL/DR         00:00:39    12.1.1.3        Serial1/0

有DR与BDR的选举。

R2#sho ip ospf int

Serial1/0 is up, line protocol is up

  Internet Address 12.1.1.2/24, Area 0

  Process ID 10, Router ID 2.2.2.2, Network Type BROADCAST, Cost: 64

  Transmit Delay is 1 sec, State BDR, Priority 1

  Designated Router (ID) 3.3.3.3, Interface address 12.1.1.3

  Backup Designated router (ID) 2.2.2.2, Interface address 12.1.1.2

  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5

 Hello时间间隔为10s。

R2#

*Aug 14 15:02:20.443: OSPF: Send hello to 224.0.0.5 area 0 on Serial1/0 from 12.1.1.2

*Aug 14 15:02:20.959: OSPF: Rcv hello from 3.3.3.3 area 0 from Serial1/0 12.1.1.3

*Aug 14 15:02:20.963: OSPF: End of hello processing

使用224.0.0.5这个组播地址传送数据包。

Type3---- Point-to-Point

将R2，R3接口的网络类型改成Point-to-Point
R2(config-if)#ip ospf net point-to-point
R3(config-if)#ip ospf net point-to-point
很快我们就可以看到如下信息
R3(config-if)#
*Aug 14 15:06:07.559: %OSPF-5-ADJCHG: Process 10, Nbr 2.2.2.2 on Serial1/1 from LOADING to FULL, Loading Done

说明这种网络类型也不需要手动指定邻居

R2#sho ip ospf nei

 

Neighbor ID     Pri   State           Dead Time   Address         Interface

3.3.3.3           0   FULL/  -        00:00:37    12.1.1.3        Serial1/0

没有DR/BDR的选举

R2#sh ip ospf int

Serial1/0 is up, line protocol is up

  Internet Address 12.1.1.2/24, Area 0

  Process ID 10, Router ID 2.2.2.2, Network Type POINT_TO_POINT, Cost: 64

  Transmit Delay is 1 sec, State POINT_TO_POINT,

  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5

Hello时间间隔为10s

R2#

*Aug 14 15:08:25.311: OSPF: Send hello to 224.0.0.5 area 0 on Serial1/0 from 12.1.1.2

R2#

*Aug 14 15:08:30.259: OSPF: Rcv hello from 3.3.3.3 area 0 from Serial1/0 12.1.1.3

*Aug 14 15:08:30.263: OSPF: End of hello processing

同样也是使用224.0.0.5这个组播地址传送数据。

Type4---- Point-to-Multipoint

将接口改为Point-to-Multipoint

R2(config-if)#ip ospf network point-to-multipoint

R3(config-if)#ip ospf network point-to-multipoint

*Aug 14 15:10:51.739: %OSPF-5-ADJCHG: Process 10, Nbr 2.2.2.2 on Serial1/1 from LOADING to FULL, Loading Done

同样也不需要手动指定邻居

R2#sho ip ospf nei

 

Neighbor ID     Pri   State           Dead Time   Address         Interface

3.3.3.3           0   FULL/  -        00:01:48    12.1.1.3        Serial1/0

没有DR和BDR的选举

R2#sho ip ospf int

Serial1/0 is up, line protocol is up

  Internet Address 12.1.1.2/24, Area 0

  Process ID 10, Router ID 2.2.2.2, Network Type POINT_TO_MULTIPOINT, Cost: 64

  Transmit Delay is 1 sec, State POINT_TO_MULTIPOINT,

  Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5

Hello时间间隔为30s

R2#

*Aug 14 15:12:49.759: OSPF: Send hello to 224.0.0.5 area 0 on Serial1/0 from 12.1.1.2

R2#

*Aug 14 15:12:57.443: OSPF: Rcv hello from 3.3.3.3 area 0 from Serial1/0 12.1.1.3

*Aug 14 15:12:57.447: OSPF: End of hello processing

以224.0.0.5这个组播地址发送数据

Type5---- Point-to-Multipoint（Non_Broadcast）

改变接口类型为Point-to-Multipoint(Non_Broadcast)
R2(config-if)#ip ospf network point-to-multipoint non-broadcast
R3(config-if)#ip ospf network point-to-multipoint non-broadcast

这个时候邻居没有被自动发现。我们在R2上手动指定邻居

R2(config-if)#router ospf 10

R2(config-router)#neighbor 12.1.1.3

R2(config-router)#

*Aug 14 15:18:38.955: %OSPF-5-ADJCHG: Process 10, Nbr 3.3.3.3 on Serial1/0 from LOADING to FULL, Loading Done

邻居只要在一边指定即可。说明在这种网络类型下邻居需要手动指定。

R2#sho ip ospf nei

 

Neighbor ID     Pri   State           Dead Time   Address         Interface

3.3.3.3           0   FULL/  -        00:01:57    12.1.1.3        Serial1/0

同样没有DR和BDR的选取

R2#sho ip ospf int

Serial1/0 is up, line protocol is up

  Internet Address 12.1.1.2/24, Area 0

  Process ID 10, Router ID 2.2.2.2, Network Type POINT_TO_MULTIPOINT, Cost: 64

  Transmit Delay is 1 sec, State POINT_TO_MULTIPOINT,

  Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5

Hello时间间隔为30s

R2#

*Aug 14 15:21:03.099: OSPF: Send hello to 12.1.1.3 area 0 on Serial1/0 from 12.1.1.2

*Aug 14 15:21:03.295: OSPF: Rcv hello from 3.3.3.3 area 0 from Serial1/0 12.1.1.3

*Aug 14 15:21:03.299: OSPF: End of hello processing

使用单播传送OSPF数据。

 

 

总结：在NBMA网络下5种网络类型具体情况如下表所示：

网络类型

邻居自动发现

有无 DR 选举

Hello 间隔

传输方式

Non_broadcast

否

有

30s

单播

Broadcast

是

有

10s

组播

Point-to-Point

是

无

10s

组播

Point-to-Multipoint

是

无

30s

组播

Point-to-Multipoint( 非广播 )

否

无

30s

单播

 

本文出自 “ 盖如鹤的步徒” 博客，请务必保留此出处 http://gairuhe.blog.51cto.com/77728/38241