Network Working Group Audio-Video Transport Working Group Request for Comments: 1889 H. Schulzrinne Category: Standards Track GMD Fokus S. Casner Precept Software, Inc. R. Frederick Xerox Palo Alto Research Center V. Jacobson Lawrence Berkeley National Laboratory January 1996 RTP: A Transport Protocol for Real-Time Applications Status of this Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Abstract This memorandum describes RTP, the real-time transport protocol. RTP provides end-to-end network transport functions suitable for applications transmitting real-time data, such as audio, video or simulation data, over multicast or unicast network services. RTP does not address resource reservation and does not guarantee quality-of- service for real-time services. The data transport is augmented by a control protocol (RTCP) to allow monitoring of the data delivery in a manner scalable to large multicast networks, and to provide minimal control and identification functionality. RTP and RTCP are designed to be independent of the underlying transport and network layers. The protocol supports the use of RTP-level translators and mixers. Table of Contents 1. Introduction ........................................ 3 2. RTP Use Scenarios ................................... 5 2.1 Simple Multicast Audio Conference ................... 5 2.2 Audio and Video Conference .......................... 6 2.3 Mixers and Translators .............................. 6 3. Definitions ......................................... 7 4. Byte Order, Alignment, and Time Format .............. 9 5. RTP Data Transfer Protocol .......................... 10 5.1 RTP Fixed Header Fields ............................. 10 5.2 Multiplexing RTP Sessions ........................... 13 Schulzrinne, et al Standards Track [Page 1] RFC 1889 RTP January 1996 5.3 Profile-Specific Modifications to the RTP Header..... 14 5.3.1 RTP Header Extension ................................ 14 6. RTP Control Protocol -- RTCP ........................ 15 6.1 RTCP Packet Format .................................. 17 6.2 RTCP Transmission Interval .......................... 19 6.2.1 Maintaining the number of session members ........... 21 6.2.2 Allocation of source description bandwidth .......... 21 6.3 Sender and Receiver Reports ......................... 22 6.3.1 SR: Sender report RTCP packet ....................... 23 6.3.2 RR: Receiver report RTCP packet ..................... 28 6.3.3 Extending the sender and receiver reports ........... 29 6.3.4 Analyzing sender and receiver reports ............... 29 6.4 SDES: Source description RTCP packet ................ 31 6.4.1 CNAME: Canonical end-point identifier SDES item ..... 32 6.4.2 NAME: User name SDES item ........................... 34 6.4.3 EMAIL: Electronic mail address SDES item ............ 34 6.4.4 PHONE: Phone number SDES item ....................... 34 6.4.5 LOC: Geographic user location SDES item ............. 35 6.4.6 TOOL: Application or tool name SDES item ............ 35 6.4.7 NOTE: Notice/status SDES item ....................... 35 6.4.8 PRIV: Private extensions SDES item .................. 36 6.5 BYE: Goodbye RTCP packet ............................ 37 6.6 APP: Application-defined RTCP packet ................ 38 7. RTP Translators and Mixers .......................... 39 7.1 General Description ................................. 39 7.2 RTCP Processing in Translators ...................... 41 7.3 RTCP Processing in Mixers ........................... 43 7.4 Cascaded Mixers ..................................... 44 8. ×××C Identifier Allocation and Use .................. 44 8.1 Probability of Collision ............................ 44 8.2 Collision Resolution and Loop Detection ............. 45 9. Security ............................................ 49 9.1 Confidentiality ..................................... 49 9.2 Authentication and Message Integrity ................ 50 10. RTP over Network and Transport Protocols ............ 51 11. Summary of Protocol Constants ....................... 51 11.1 RTCP packet types ................................... 52 11.2 SDES types .......................................... 52 12. RTP Profiles and Payload Format Specifications ...... 53 A. Algorithms .......................................... 56 A.1 RTP Data Header Validity Checks ..................... 59 A.2 RTCP Header Validity Checks ......................... 63 A.3 Determining the Number of RTP Packets Expected and Lost ................................................ 63 A.4 Generating SDES RTCP Packets ........................ 64 A.5 Parsing RTCP SDES Packets ........................... 65 A.6 Generating a Random 32-bit Identifier ............... 66 A.7 Computing the RTCP Transmission Interval ............ 68 Schulzrinne, et al Standards Track [Page 2] RFC 1889 RTP January 1996 A.8 Estimating the Interarrival Jitter .................. 71 B. Security Considerations ............................. 72 C. Addresses of Authors ................................ 72 D. Bibliography ........................................ 73 1. Introduction This memorandum specifies the real-time transport protocol (RTP), which provides end-to-end delivery services for data with real-time characteristics, such as interactive audio and video. Those services include payload type identification, sequence numbering, timestamping and delivery monitoring. Applications typically run RTP on top of UDP to make use of its multiplexing and checksum services; both protocols contribute parts of the transport protocol functionality. However, RTP may be used with other suitable underlying network or transport protocols (see Section 10). RTP supports data transfer to multiple destinations using multicast distribution if provided by the underlying network. Note that RTP itself does not provide any mechanism to ensure timely delivery or provide other quality-of-service guarantees, but relies on lower-layer services to do so. It does not guarantee delivery or prevent out-of-order delivery, nor does it assume that the underlying network is reliable and delivers packets in sequence. The sequence numbers included in RTP allow the receiver to reconstruct the sender's packet sequence, but sequence numbers might also be used to determine the proper location of a packet, for example in video decoding, without necessarily decoding packets in sequence. While RTP is primarily designed to satisfy the needs of multi- participant multimedia conferences, it is not limited to that particular application. Storage of continuous data, interactive distributed simulation, active badge, and control and measurement applications may also find RTP applicable. This document defines RTP, consisting of two closely-linked parts: o the real-time transport protocol (RTP), to carry data that has real-time properties. o the RTP control protocol (RTCP), to monitor the quality of service and to convey information about the participants in an on-going session. The latter aspect of RTCP may be sufficient for "loosely controlled" sessions, i.e., where there is no explicit membership control and set-up, but it is not necessarily intended to support all of an application's control communication requirements. This functionality may be fully or partially subsumed by a separate session control protocol, Schulzrinne, et al Standards Track [Page 3] RFC 1889 RTP January 1996 which is beyond the scope of this document. RTP represents a new style of protocol following the principles of application level framing and integrated layer processing proposed by Clark and Tennenhouse [1]. That is, RTP is intended to be malleable to provide the information required by a particular application and will often be integrated into the application processing rather than being implemented as a separate layer. RTP is a protocol framework that is deliberately not complete. This document specifies those functions expected to be common across all the applications for which RTP would be appropriate. Unlike conventional protocols in which additional functions might be accommodated by making the protocol more general or by adding an option mechanism that would require parsing, RTP is intended to be tailored through modifications and/or additions to the headers as needed. Examples are given in Sections 5.3 and 6.3.3. Therefore, in addition to this document, a complete specification of RTP for a particular application will require one or more companion documents (see Section 12): o a profile specification document, which defines a set of payload type codes and their mapping to payload formats (e.g., media encodings). A profile may also define extensions or modifications to RTP that are specific to a particular class of applications. Typically an application will operate under only one profile. A profile for audio and video data may be found in the companion RFC TBD. o payload format specification documents, which define how a particular payload, such as an audio or video encoding, is to be carried in RTP. A discussion of real-time services and algorithms for their implementation as well as background discussion on some of the RTP design decisions can be found in [2]. Several RTP applications, both experimental and commercial, have already been implemented from draft specifications. These applications include audio and video tools along with diagnostic tools such as traffic monitors. Users of these tools number in the thousands. However, the current Internet cannot yet support the full potential demand for real-time services. High-bandwidth services using RTP, such as video, can potentially seriously degrade the quality of service of other network services. Thus, implementors should take appropriate precautions to limit accidental bandwidth usage. Application documentation should clearly outline the limitations and possible operational impact of high-bandwidth real- Schulzrinne, et al Standards Track [Page 4] RFC 1889 RTP January 1996 time services on the Internet and other network services. 2. RTP Use Scenarios The following sections describe some aspects of the use of RTP. The examples were chosen to illustrate the basic operation of applications using RTP, not to limit what RTP may be used for. In these examples, RTP is carried on top of IP and UDP, and follows the conventions established by the profile for audio and video specified in the companion Internet-Draft draft-ietf-avt-profile 2.1 Simple Multicast Audio Conference A working group of the IETF meets to discuss the latest protocol draft, using the IP multicast services of the Internet for voice communications. Through some allocation mechanism the working group chair obtains a multicast group address and pair of ports. One port is used for audio data, and the other is used for control (RTCP) packets. This address and port information is distributed to the intended participants. If privacy is desired, the data and control packets may be encrypted as specified in Section 9.1, in which case an encryption key must also be generated and distributed. The exact details of these allocation and distribution mechanisms are beyond the scope of RTP. The audio conferencing application used by each conference participant sends audio data in small chunks of, say, 20 ms duration. Each chunk of audio data is preceded by an RTP header; RTP header and data are in turn contained in a UDP packet. The RTP header indicates what type of audio encoding (such as PCM, ADPCM or LPC) is contained in each packet so that senders can change the encoding during a conference, for example, to accommodate a new participant that is connected through a low-bandwidth link or react to indications of network congestion. The Internet, like other packet networks, occasionally loses and reorders packets and delays them by variable amounts of time. To cope with these impairments, the RTP header contains timing information and a sequence number that allow the receivers to reconstruct the timing produced by the source, so that in this example, chunks of audio are contiguously played out the speaker every 20 ms. This timing reconstruction is performed separately for each source of RTP packets in the conference. The sequence number can also be used by the receiver to estimate how many packets are being lost. Since members of the working group join and leave during the conference, it is useful to know who is participating at any moment and how well they are receiving the audio data. For that purpose, Schulzrinne, et al Standards Track [Page 5] RFC 1889 RTP January 1996 each instance of the audio application in the conference periodically multicasts a reception report plus the name of its user on the RTCP (control) port. The reception report indicates how well the current speaker is being received and may be used to control adaptive encodings. In addition to the user name, other identifying information may also be included subject to control bandwidth limits. A site sends the RTCP BYE packet (Section 6.5) when it leaves the conference. 2.2 Audio and Video Conference If both audio and video media are used in a conference, they are transmitted as separate RTP sessions RTCP packets are transmitted for each medium using two different UDP port pairs and/or multicast addresses. There is no direct coupling at the RTP level between the audio and video sessions, except that a user participating in both sessions should use the same distinguished (canonical) name in the RTCP packets for both so that the sessions can be associated. One motivation for this separation is to allow some participants in the conference to receive only one medium if they choose. Further explanation is given in Section 5.2. Despite the separation, synchronized playback of a source's audio and video can be achieved using timing information carried in the RTCP packets for both sessions. 2.3 Mixers and Translators So far, we have assumed that all sites want to receive media data in the same format. However, this may not always be appropriate. Consider the case where participants in one area are connected through a low-speed link to the majority of the conference participants who enjoy high-speed network access. Instead of forcing everyone to use a lower-bandwidth, reduced-quality audio encoding, an RTP-level relay called a mixer may be placed near the low-bandwidth area. This mixer resynchronizes incoming audio packets to reconstruct the constant 20 ms spacing generated by the sender, mixes these reconstructed audio streams into a single stream, translates the audio encoding to a lower-bandwidth one and forwards the lower- bandwidth packet stream across the low-speed link. These packets might be unicast to a single recipient or multicast on a different address to multiple recipients. The RTP header includes a means for mixers to identify the sources that contributed to a mixed packet so that correct talker indication can be provided at the receivers. Some of the intended participants in the audio conference may be connected with high bandwidth links but might not be directly reachable via IP multicast. For example, they might be behind an Schulzrinne, et al Standards Track [Page 6] RFC 1889 RTP January 1996 application-level firewall that will not let any IP packets pass. For these sites, mixing may not be necessary, in which case another type of RTP-level relay called a translator may be used. Two translators are installed, one on either side of the firewall, with the outside one funneling all multicast packets received through a secure connection to the translator inside the firewall. The translator inside the firewall sends them again as multicast packets to a multicast group restricted to the site's internal network. Mixers and translators may be designed for a variety of purposes. An example is a video mixer that scales the p_w_picpaths of individual people in separate video streams and composites them into one video stream to simulate a group scene. Other examples of translation include the connection of a group of hosts speaking only IP/UDP to a group of hosts that understand only ST-II, or the packet-by-packet encoding translation of video streams from individual sources without resynchronization or mixing. Details of the operation of mixers and translators are given in Section 7. 3. Definitions RTP payload: The data transported by RTP in a packet, for example audio samples or compressed video data. The payload format and interpretation are beyond the scope of this document. RTP packet: A data packet consisting of the fixed RTP header, a possibly empty list of contributing sources (see below), and the payload data. Some underlying protocols may require an encapsulation of the RTP packet to be defined. Typically one packet of the underlying protocol contains a single RTP packet, but several RTP packets may be contained if permitted by the encapsulation method (see Section 10). RTCP packet: A control packet consisting of a fixed header part similar to that of RTP data packets, followed by structured elements that vary depending upon the RTCP packet type. The formats are defined in Section 6. Typically, multiple RTCP packets are sent together as a compound RTCP packet in a single packet of the underlying protocol; this is enabled by the length field in the fixed header of each RTCP packet. Port: The "abstraction that transport protocols use to distinguish among multiple destinations within a given host computer. TCP/IP protocols identify ports using small positive integers." [3] The transport selectors (TSEL) used by the OSI transport layer are equivalent to ports. RTP depends upon the lower-layer protocol to provide some mechanism such as ports to multiplex the RTP and RTCP packets of a session. Schulzrinne, et al Standards Track [Page 7] RFC 1889 RTP January 1996 Transport address: The combination of a network address and port that identifies a transport-level endpoint, for example an IP address and a UDP port. Packets are transmitted from a source transport address to a destination transport address. RTP session: The association among a set of participants communicating with RTP. For each participant, the session is defined by a particular pair of destination transport addresses (one network address plus a port pair for RTP and RTCP). The destination transport address pair may be common for all participants, as in the case of IP multicast, or may be different for each, as in the case of individual unicast network addresses plus a common port pair. In a multimedia session, each medium is carried in a separate RTP session with its own RTCP packets. The multiple RTP sessions are distinguished by different port number pairs and/or different multicast addresses. Synchronization source (×××C): The source of a stream of RTP packets, identified by a 32-bit numeric ×××C identifier carried in the RTP header so as not to be dependent upon the network address. All packets from a synchronization source form part of the same timing and sequence number space, so a receiver groups packets by synchronization source for playback. Examples of synchronization sources include the sender of a stream of packets derived from a signal source such as a microphone or a camera, or an RTP mixer (see below). A synchronization source may change its data format, e.g., audio encoding, over time. The ×××C identifier is a randomly chosen value meant to be globally unique within a particular RTP session (see Section 8). A participant need not use the same ×××C identifier for all the RTP sessions in a multimedia session; the binding of the ×××C identifiers is provided through RTCP (see Section 6.4.1). If a participant generates multiple streams in one RTP session, for example from separate video cameras, each must be identified as a different ×××C. Contributing source (CSRC): A source of a stream of RTP packets that has contributed to the combined stream produced by an RTP mixer (see below). The mixer inserts a list of the ×××C identifiers of the sources that contributed to the generation of a particular packet into the RTP header of that packet. This list is called the CSRC list. An example application is audio conferencing where a mixer indicates all the talkers whose speech was combined to produce the outgoing packet, allowing the receiver to indicate the current talker, even though all the audio packets contain the same ×××C identifier (that of the mixer). Schulzrinne, et al Standards Track [Page 8] RFC 1889 RTP January 1996 End system: An application that generates the content to be sent in RTP packets and/or consumes the content of received RTP packets. An end system can act as one or more synchronization sources in a particular RTP session, but typically only one. Mixer: An intermediate system that receives RTP packets from one or more sources, possibly changes the data format, combines the packets in some manner and then forwards a new RTP packet. Since the timing among multiple input sources will not generally be synchronized, the mixer will make timing adjustments among the streams and generate its own timing for the combined stream. Thus, all data packets originating from a mixer will be identified as having the mixer as their synchronization source. Translator: An intermediate system that forwards RTP packets with their synchronization source identifier intact. Examples of translators include devices that convert encodings without mixing, replicators from multicast to unicast, and application- level filters in firewalls. Monitor: An application that receives RTCP packets sent by participants in an RTP session, in particular the reception reports, and estimates the current quality of service for distribution monitoring, fault diagnosis and long-term statistics. The monitor function is likely to be built into the application(s) participating in the session, but may also be a separate application that does not otherwise participate and does not send or receive the RTP data packets. These are called third party monitors. Non-RTP means: Protocols and mechanisms that may be needed in addition to RTP to provide a usable service. In particular, for multimedia conferences, a conference control application may distribute multicast addresses and keys for encryption, negotiate the encryption algorithm to be used, and define dynamic mappings between RTP payload type values and the payload formats they represent for formats that do not have a predefined payload type value. For simple applications, electronic mail or a conference database may also be used. The specification of such protocols and mechanisms is outside the scope of this document. 4. Byte Order, Alignment, and Time Format All integer fields are carried in network byte order, that is, most significant byte (octet) first. This byte order is commonly known as big-endian. The transmission order is described in detail in [4]. Unless otherwise noted, numeric constants are in decimal (base 10). Schulzrinne, et al Standards Track [Page 9] RFC 1889 RTP January 1996 All header data is aligned to its natural length, i.e., 16-bit fields are aligned on even offsets, 32-bit fields are aligned at offsets divisible by four, etc. Octets designated as padding have the value zero. Wallclock time (absolute time) is represented using the timestamp format of the Network Time Protocol (NTP), which is in seconds relative to 0h UTC on 1 January 1900 [5]. The full resolution NTP timestamp is a 64-bit unsigned fixed-point number with the integer part in the first 32 bits and the fractional part in the last 32 bits. In some fields where a more compact representation is appropriate, only the middle 32 bits are used; that is, the low 16 bits of the integer part and the high 16 bits of the fractional part. The high 16 bits of the integer part must be determined independently. 5. RTP Data Transfer Protocol 5.1 RTP Fixed Header Fields The RTP header has the following format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |V=2|P|X| CC |M| PT | sequence number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | timestamp | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | synchronization source (×××C) identifier | +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+ | contributing source (CSRC) identifiers | | .... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The first twelve octets are present in every RTP packet, while the list of CSRC identifiers is present only when inserted by a mixer. The fields have the following meaning: version (V): 2 bits This field identifies the version of RTP. The version defined by this specification is two (2). (The value 1 is used by the first draft version of RTP and the value 0 is used by the protocol initially implemented in the "vat" audio tool.) padding (P): 1 bit If the padding bit is set, the packet contains one or more additional padding octets at the end which are not part of the Schulzrinne, et al Standards Track [Page 10] RFC 1889 RTP January 1996 payload. The last octet of the padding contains a count of how many padding octets should be ignored. Padding may be needed by some encryption algorithms with fixed block sizes or for carrying several RTP packets in a lower-layer protocol data unit. extension (X): 1 bit If the extension bit is set, the fixed header is followed by exactly one header extension, with a format defined in Section 5.3.1. CSRC count (CC): 4 bits The CSRC count contains the number of CSRC identifiers that follow the fixed header. marker (M): 1 bit The interpretation of the marker is defined by a profile. It is intended to allow significant events such as frame boundaries to be marked in the packet stream. A profile may define additional marker bits or specify that there is no marker bit by changing the number of bits in the payload type field (see Section 5.3). payload type (PT): 7 bits This field identifies the format of the RTP payload and determines its interpretation by the application. A profile specifies a default static mapping of payload type codes to payload formats. Additional payload type codes may be defined dynamically through non-RTP means (see Section 3). An initial set of default mappings for audio and video is specified in the companion profile Internet-Draft draft-ietf-avt-profile, and may be extended in future editions of the Assigned Numbers RFC [6]. An RTP sender emits a single RTP payload type at any given time; this field is not intended for multiplexing separate media streams (see Section 5.2). sequence number: 16 bits The sequence number increments by one for each RTP data packet sent, and may be used by the receiver to detect packet loss and to restore packet sequence. The initial value of the sequence number is random (unpredictable) to make known-plaintext attacks on encryption more difficult, even if the source itself does not encrypt, because the packets may flow through a translator that does. Techniques for choosing unpredictable numbers are discussed in [7]. timestamp: 32 bits The timestamp reflects the sampling instant of the first octet in the RTP data packet. The sampling instant must be derived Schulzrinne, et al Standards Track [Page 11] RFC 1889 RTP January 1996 from a clock that increments monotonically and linearly in time to allow synchronization and jitter calculations (see Section 6.3.1). The resolution of the clock must be sufficient for the desired synchronization accuracy and for measuring packet arrival jitter (one tick per video frame is typically not sufficient). The clock frequency is dependent on the format of data carried as payload and is specified statically in the profile or payload format specification that defines the format, or may be specified dynamically for payload formats defined through non-RTP means. If RTP packets are generated periodically, the nominal sampling instant as determined from the sampling clock is to be used, not a reading of the system clock. As an example, for fixed-rate audio the timestamp clock would likely increment by one for each sampling period. If an audio application reads blocks covering 160 sampling periods from the input device, the timestamp would be increased by 160 for each such block, regardless of whether the block is transmitted in a packet or dropped as silent. The initial value of the timestamp is random, as for the sequence number. Several consecutive RTP packets may have equal timestamps if they are (logically) generated at once, e.g., belong to the same video frame. Consecutive RTP packets may contain timestamps that are not monotonic if the data is not transmitted in the order it was sampled, as in the case of MPEG interpolated video frames. (The sequence numbers of the packets as transmitted will still be monotonic.) ×××C: 32 bits The ×××C field identifies the synchronization source. This identifier is chosen randomly, with the intent that no two synchronization sources within the same RTP session will have the same ×××C identifier. An example algorithm for generating a random identifier is presented in Appendix A.6. Although the probability of multiple sources choosing the same identifier is low, all RTP implementations must be prepared to detect and resolve collisions. Section 8 describes the probability of collision along with a mechanism for resolving collisions and detecting RTP-level forwarding loops based on the uniqueness of the ×××C identifier. If a source changes its source transport address, it must also choose a new ×××C identifier to avoid being interpreted as a looped source. CSRC list: 0 to 15 items, 32 bits each The CSRC list identifies the contributing sources for the payload contained in this packet. The number of identifiers is given by the CC field. If there are more than 15 contributing sources, only 15 may be identified. CSRC identifiers are Schulzrinne, et al Standards Track [Page 12] RFC 1889 RTP January 1996 inserted by mixers, using the ×××C identifiers of contributing sources. For example, for audio packets the ×××C identifiers of all sources that were mixed together to create a packet are listed, allowing correct talker indication at the receiver. 5.2 Multiplexing RTP Sessions For efficient protocol processing, the number of multiplexing points should be minimized, as described in the integrated layer processing design principle [1]. In RTP, multiplexing is provided by the destination transport address (network address and port number) which define an RTP session. For example, in a teleconference composed of audio and video media encoded separately, each medium should be carried in a separate RTP session with its own destination transport address. It is not intended that the audio and video be carried in a single RTP session and demultiplexed based on the payload type or ×××C fields. Interleaving packets with different payload types but using the same ×××C would introduce several problems: 1. If one payload type were switched during a session, there would be no general means to identify which of the old values the new one replaced. 2. An ×××C is defined to identify a single timing and sequence number space. Interleaving multiple payload types would require different timing spaces if the media clock rates differ and would require different sequence number spaces to tell which payload type suffered packet loss. 3. The RTCP sender and receiver reports (see Section 6.3) can only describe one timing and sequence number space per ×××C and do not carry a payload type field. 4. An RTP mixer would not be able to combine interleaved streams of incompatible media into one stream. 5. Carrying multiple media in one RTP session precludes: the use of different network paths or network resource allocations if appropriate; reception of a subset of the media if desired, for example just audio if video would exceed the available bandwidth; and receiver implementations that use separate processes for the different media, whereas using separate RTP sessions permits either single- or multiple-process implementations. Using a different ×××C for each medium but sending them in the same RTP session would avoid the first three problems but not the last two. Schulzrinne, et al Standards Track [Page 13] RFC 1889 RTP January 1996 5.3 Profile-Specific Modifications to the RTP Header The existing RTP data packet header is believed to be complete for the set of functions required in common across all the application classes that RTP might support. However, in keeping with the ALF design principle, the header may be tailored through modifications or additions defined in a profile specification while still allowing profile-independent monitoring and recording tools to function. o The marker bit and payload type field carry profile-specific information, but they are allocated in the fixed header since many applications are expected to need them and might otherwise have to add another 32-bit word just to hold them. The octet containing these fields may be redefined by a profile to suit different requirements, for example with a more or fewer marker bits. If there are any marker bits, one should be located in the most significant bit of the octet since profile-independent monitors may be able to observe a correlation between packet loss patterns and the marker bit. o Additional information that is required for a particular payload format, such as a video encoding, should be carried in the payload section of the packet. This might be in a header that is always present at the start of the payload section, or might be indicated by a reserved value in the data pattern. o If a particular class of applications needs additional functionality independent of payload format, the profile under which those applications operate should define additional fixed fields to follow immediately after the ×××C field of the existing fixed header. Those applications will be able to quickly and directly access the additional fields while profile-independent monitors or recorders can still process the RTP packets by interpreting only the first twelve octets. If it turns out that additional functionality is needed in common across all profiles, then a new version of RTP should be defined to make a permanent change to the fixed header. 5.3.1 RTP Header Extension An extension mechanism is provided to allow individual implementations to experiment with new payload-format-independent functions that require additional information to be carried in the RTP data packet header. This mechanism is designed so that the header extension may be ignored by other interoperating implementations that have not been extended. Schulzrinne, et al Standards Track [Page 14] RFC 1889 RTP January 1996 Note that this header extension is intended only for limited use. Most potential uses of this mechanism would be better done another way, using the methods described in the previous section. For example, a profile-specific extension to the fixed header is less expensive to process because it is not conditional nor in a variable location. Additional information required for a particular payload format should not use this header extension, but should be carried in the payload section of the packet. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | defined by profile | length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | header extension | | .... | If the X bit in the RTP header is one, a variable-length header extension is appended to the RTP header, following the CSRC list if present. The header extension contains a 16-bit length field that counts the number of 32-bit words in the extension, excluding the four-octet extension header (therefore zero is a valid length). Only a single extension may be appended to the RTP data header. To allow multiple interoperating implementations to each experiment independently with different header extensions, or to allow a particular implementation to experiment with more than one type of header extension, the first 16 bits of the header extension are left open for distinguishing identifiers or parameters. The format of these 16 bits is to be defined by the profile specification under which the implementations are operating. This RTP specification does not define any header extensions itself. 6. RTP Control Protocol -- RTCP The RTP control protocol (RTCP) is based on the periodic transmission of control packets to all participants in the session, using the same distribution mechanism as the data packets. The underlying protocol must provide multiplexing of the data and control packets, for example using separate port numbers with UDP. RTCP performs four functions: 1. The primary function is to provide feedback on the quality of the data distribution. This is an integral part of the RTP's role as a transport protocol and is related to the flow and congestion control functions of other transport protocols. The feedback may be directly useful for control of adaptive encodings [8,9], but experiments with IP Schulzrinne, et al Standards Track [Page 15] RFC 1889 RTP January 1996 multicasting have shown that it is also critical to get feedback from the receivers to diagnose faults in the distribution. Sending reception feedback reports to all participants allows one who is observing problems to evaluate whether those problems are local or global. With a distribution mechanism like IP multicast, it is also possible for an entity such as a network service provider who is not otherwise involved in the session to receive the feedback information and act as a third-party monitor to diagnose network problems. This feedback function is performed by the RTCP sender and receiver reports, described below in Section 6.3. 2. RTCP carries a persistent transport-level identifier for an RTP source called the canonical name or CNAME, Section 6.4.1. Since the ×××C identifier may change if a conflict is discovered or a program is restarted, receivers require the CNAME to keep track of each participant. Receivers also require the CNAME to associate multiple data streams from a given participant in a set of related RTP sessions, for example to synchronize audio and video. 3. The first two functions require that all participants send RTCP packets, therefore the rate must be controlled in order for RTP to scale up to a large number of participants. By having each participant send its control packets to all the others, each can independently observe the number of participants. This number is used to calculate the rate at which the packets are sent, as explained in Section 6.2. 4. A fourth, optional function is to convey minimal session control information, for example participant identification to be displayed in the user interface. This is most likely to be useful in "loosely controlled" sessions where participants enter and leave without membership control or parameter negotiation. RTCP serves as a convenient channel to reach all the participants, but it is not necessarily expected to support all the control communication requirements of an application. A higher-level session control protocol, which is beyond the scope of this document, may be needed. Functions 1-3 are mandatory when RTP is used in the IP multicast environment, and are recommended for all environments. RTP application designers are advised to avoid mechanisms that can only work in unicast mode and will not scale to larger numbers. Schulzrinne, et al Standards Track [Page 16] RFC 1889 RTP January 1996 6.1 RTCP Packet Format This specification defines several RTCP packet types to carry a variety of control information: SR: Sender report, for transmission and reception statistics from participants that are active senders RR: Receiver report, for reception statistics from participants that are not active senders SDES: Source description items, including CNAME BYE: Indicates end of participation APP: Application specific functions Each RTCP packet begins with a fixed part similar to that of RTP data packets, followed by structured elements that may be of variable length according to the packet type but always end on a 32-bit boundary. The alignment requirement and a length field in the fixed part are included to make RTCP packets "stackable". Multiple RTCP packets may be concatenated without any intervening separators to form a compound RTCP packet that is sent in a single packet of the lower layer protocol, for example UDP. There is no explicit count of individual RTCP packets in the compound packet since the lower layer protocols are expected to provide an overall length to determine the end of the compound packet. Each individual RTCP packet in the compound packet may be processed independently with no requirements upon the order or combination of packets. However, in order to perform the functions of the protocol, the following constraints are imposed: o Reception statistics (in SR or RR) should be sent as often as bandwidth constraints will allow to maximize the resolution of the statistics, therefore each periodically transmitted compound RTCP packet should include a report packet. o New receivers need to receive the CNAME for a source as soon as possible to identify the source and to begin associating media for purposes such as lip-sync, so each compound RTCP packet should also include the SDES CNAME. o The number of packet types that may appear first in the compound packet should be limited to increase the number of constant bits in the first word and the probability of successfully validating RTCP packets against misaddressed RTP Schulzrinne, et al Standards Track [Page 17] RFC 1889 RTP January 1996 data packets or other unrelated packets. Thus, all RTCP packets must be sent in a compound packet of at least two individual packets, with the following format recommended: Encryption prefix: If and only if the compound packet is to be encrypted, it is prefixed by a random 32-bit quantity redrawn for every compound packet transmitted. SR or RR: The first RTCP packet in the compound packet must always be a report packet to facilitate header validation as described in Appendix A.2. This is true even if no data has been sent nor received, in which case an empty RR is sent, and even if the only other RTCP packet in the compound packet is a BYE. Additional RRs: If the number of sources for which reception statistics are being reported exceeds 31, the number that will fit into one SR or RR packet, then additional RR packets should follow the initial report packet. SDES: An SDES packet containing a CNAME item must be included in each compound RTCP packet. Other source description items may optionally be included if required by a particular application, subject to bandwidth constraints (see Section 6.2.2). BYE or APP: Other RTCP packet types, including those yet to be defined, may follow in any order, except that BYE should be the last packet sent with a given ×××C/CSRC. Packet types may appear more than once. It is advisable for translators and mixers to combine individual RTCP packets from the multiple sources they are forwarding into one compound packet whenever feasible in order to amortize the packet overhead (see Section 7). An example RTCP compound packet as might be produced by a mixer is shown in Fig. 1. If the overall length of a compound packet would exceed the maximum transmission unit (MTU) of the network path, it may be segmented into multiple shorter compound packets to be transmitted in separate packets of the underlying protocol. Note that each of the compound packets must begin with an SR or RR packet. An implementation may ignore incoming RTCP packets with types unknown to it. Additional RTCP packet types may be registered with the Internet Assigned Numbers Authority (IANA). Schulzrinne, et al Standards Track [Page 18] RFC 1889 RTP January 1996 6.2 RTCP Transmission Interval if encrypted: random 32-bit integer | |[------- packet -------][----------- packet -----------][-packet-] | | receiver reports chunk chunk V item item item item -------------------------------------------------------------------- |R[SR|# sender #site#site][SDES|# CNAME PHONE |#CNAME LOC][BYE##why] |R[ |# report # 1 # 2 ][ |# |# ][ ## ] |R[ |# # # ][ |# |# ][ ## ] |R[ |# # # ][ |# |# ][ ## ] -------------------------------------------------------------------- |<------------------ UDP packet (compound packet) --------------->| #: ×××C/CSRC Figure 1: Example of an RTCP compound packet RTP is designed to allow an application to scale automatically over session sizes ranging from a few participants to thousands. For example, in an audio conference the data traffic is inherently self- limiting because only one or two people will speak at a time, so with multicast distribution the data rate on any given link remains relatively constant independent of the number of participants. However, the control traffic is not self-limiting. If the reception reports from each participant were sent at a constant rate, the control traffic would grow linearly with the number of participants. Therefore, the rate must be scaled down. For each session, it is assumed that the data traffic is subject to an aggregate limit called the "session bandwidth" to be divided among the participants. This bandwidth might be reserved and the limit enforced by the network, or it might just be a reasonable share. The session bandwidth may be chosen based or some cost or a priori knowledge of the available network bandwidth for the session. It is somewhat independent of the media encoding, but the encoding choice may be limited by the session bandwidth. The session bandwidth parameter is expected to be supplied by a session management application when it invokes a media application, but media applications may also set a default based on the single-sender data bandwidth for the encoding selected for the session. The application may also enforce bandwidth limits based on multicast scope rules or other criteria. Schulzrinne, et al Standards Track [Page 19] RFC 1889 RTP January 1996 Bandwidth calculations for control and data traffic include lower- layer transport and network protocols (e.g., UDP and IP) since that is what the resource reservation system would need to know. The application can also be expected to know which of these protocols are in use. Link level headers are not included in the calculation since the packet will be encapsulated with different link level headers as it travels. The control traffic should be limited to a small and known fraction of the session bandwidth: small so that the primary function of the transport protocol to carry data is not impaired; known so that the control traffic can be included in the bandwidth specification given to a resource reservation protocol, and so that each participant can independently calculate its share. It is suggested that the fraction of the session bandwidth allocated to RTCP be fixed at 5%. While the value of this and other constants in the interval calculation is not critical, all participants in the session must use the same values so the same interval will be calculated. Therefore, these constants should be fixed for a particular profile. The algorithm described in Appendix A.7 was designed to meet the goals outlined above. It calculates the interval between sending compound RTCP packets to divide the allowed control traffic bandwidth among the participants. This allows an application to provide fast response for small sessions where, for example, identification of all participants is important, yet automatically adapt to large sessions. The algorithm incorporates the following characteristics: o Senders are collectively allocated at least 1/4 of the control traffic bandwidth so that in sessions with a large number of receivers but a small number of senders, newly joining participants will more quickly receive the CNAME for the sending sites. o The calculated interval between RTCP packets is required to be greater than a minimum of 5 seconds to avoid having bursts of RTCP packets exceed the allowed bandwidth when the number of participants is small and the traffic isn't smoothed according to the law of large numbers. o The interval between RTCP packets is varied randomly over the range [0.5,1.5] times the calculated interval to avoid unintended synchronization of all participants [10]. The first RTCP packet sent after joining a session is also delayed by a random variation of half the minimum RTCP interval in case the application is started at multiple sites simultaneously, for example as initiated by a session announcement. Schulzrinne, et al Standards Track [Page 20] RFC 1889 RTP January 1996 o A dynamic estimate of the average compound RTCP packet size is calculated, including all those received and sent, to automatically adapt to changes in the amount of control information carried. This algorithm may be used for sessions in which all participants are allowed to send. In that case, the session bandwidth parameter is the product of the individual sender's bandwidth times the number of participants, and the RTCP bandwidth is 5% of that. 6.2.1 Maintaining the number of session members Calculation of the RTCP packet interval depends upon an estimate of the number of sites participating in the session. New sites are added to the count when they are heard, and an entry for each is created in a table indexed by the ×××C or CSRC identifier (see Section 8.2) to keep track of them. New entries may not be considered valid until multiple packets carrying the new ×××C have been received (see Appendix A.1). Entries may be deleted from the table when an RTCP BYE packet with the corresponding ×××C identifier is received. A participant may mark another site inactive, or delete it if not yet valid, if no RTP or RTCP packet has been received for a small number of RTCP report intervals (5 is suggested). This provides some robustness against packet loss. All sites must calculate roughly the same value for the RTCP report interval in order for this timeout to work properly. Once a site has been validated, then if it is later marked inactive the state for that site should still be retained and the site should continue to be counted in the total number of sites sharing RTCP bandwidth for a period long enough to span typical network partitions. This is to avoid excessive traffic, when the partition heals, due to an RTCP report interval that is too small. A timeout of 30 minutes is suggested. Note that this is still larger than 5 times the largest value to which the RTCP report interval is expected to usefully scale, about 2 to 5 minutes. 6.2.2 Allocation of source description bandwidth This specification defines several source description (SDES) items in addition to the mandatory CNAME item, such as NAME (personal name) and EMAIL (email address). It also provides a means to define new application-specific RTCP packet types. Applications should exercise caution in allocating control bandwidth to this additional information because it will slow down the rate at which reception reports and CNAME are sent, thus impairing the performance of the protocol. It is recommended that no more than 20% of the RTCP Schulzrinne, et al Standards Track [Page 21] RFC 1889 RTP January 1996 bandwidth allocated to a single participant be used to carry the additional information. Furthermore, it is not intended that all SDES items should be included in every application. Those that are included should be assigned a fraction of the bandwidth according to their utility. Rather than estimate these fractions dynamically, it is recommended that the percentages be translated statically into report interval counts based on the typical length of an item. For example, an application may be designed to send only CNAME, NAME and EMAIL and not any others. NAME might be given much higher priority than EMAIL because the NAME would be displayed continuously in the application's user interface, whereas EMAIL would be displayed only when requested. At every RTCP interval, an RR packet and an SDES packet with the CNAME item would be sent. For a small session operating at the minimum interval, that would be every 5 seconds on the average. Every third interval (15 seconds), one extra item would be included in the SDES packet. Seven out of eight times this would be the NAME item, and every eighth time (2 minutes) it would be the EMAIL item. When multiple applications operate in concert using cross-application binding through a common CNAME for each participant, for example in a multimedia conference composed of an RTP session for each medium, the additional SDES information might be sent in only one RTP session. The other sessions would carry only the CNAME item. 6.3 Sender and Receiver Reports RTP receivers provide reception quality feedback using RTCP report packets which may take one of two forms depending upon whether or not the receiver is also a sender. The only difference between the sender report (SR) and receiver report (RR) forms, besides the packet type code, is that the sender report includes a 20-byte sender information section for use by active senders. The SR is issued if a site has sent any data packets during the interval since issuing the last report or the previous one, otherwise the RR is issued. Both the SR and RR forms include zero or more reception report blocks, one for each of the synchronization sources from which this receiver has received RTP data packets since the last report. Reports are not issued for contributing sources listed in the CSRC list. Each reception report block provides statistics about the data received from the particular source indicated in that block. Since a maximum of 31 reception report blocks will fit in an SR or RR packet, additional RR packets may be stacked after the initial SR or RR packet as needed to contain the reception reports for all sources heard during the interval since the last report. Schulzrinne, et al Standards Track [Page 22] RFC 1889 RTP January 1996 The next sections define the formats of the two reports, how they may be extended in a profile-specific manner if an application requires additional feedback information, and how the reports may be used. Details of reception reporting by translators and mixers is given in Section 7. 6.3.1 SR: Sender report RTCP packet 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |V=2|P| RC | PT=SR=200 | length | header +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ×××C of sender | +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+ | NTP timestamp, most significant word | sender +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ info | NTP timestamp, least significant word | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | RTP timestamp | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | sender's packet count | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | sender's octet count | +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+ | ×××C_1 (×××C of first source) | report +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ block | fraction lost | cumulative number of packets lost | 1 -+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | extended highest sequence number received | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | interarrival jitter | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | last SR (LSR) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | delay since last SR (DLSR) | +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+ | ×××C_2 (×××C of second source) | report +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ block : ... : 2 +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+ | profile-specific extensions | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The sender report packet consists of three sections, possibly followed by a fourth profile-specific extension section if defined. The first section, the header, is 8 octets long. The fields have the following meaning: Schulzrinne, et al Standards Track [Page 23] RFC 1889 RTP January 1996 version (V): 2 bits Identifies the version of RTP, which is the same in RTCP packets as in RTP data packets. The version defined by this specification is two (2). padding (P): 1 bit If the padding bit is set, this RTCP packet contains some additional padding octets at the end which are not part of the control information. The last octet of the padding is a count of how many padding octets should be ignored. Padding may be needed by some encryption algorithms with fixed block sizes. In a compound RTCP packet, padding should only be required on the last individual packet because the compound packet is encrypted as a whole. reception report count (RC): 5 bits The number of reception report blocks contained in this packet. A value of zero is valid. packet type (PT): 8 bits Contains the constant 200 to identify this as an RTCP SR packet. length: 16 bits The length of this RTCP packet in 32-bit words minus one, including the header and any padding. (The offset of one makes zero a valid length and avoids a possible infinite loop in scanning a compound RTCP packet, while counting 32-bit words avoids a validity check for a multiple of 4.) ×××C: 32 bits The synchronization source identifier for the originator of this SR packet. The second section, the sender information, is 20 octets long and is present in every sender report packet. It summarizes the data transmissions from this sender. The fields have the following meaning: NTP timestamp: 64 bits Indicates the wallclock time when this report was sent so that it may be used in combination with timestamps returned in reception reports from other receivers to measure round-trip propagation to those receivers. Receivers should expect that the measurement accuracy of the timestamp may be limited to far less than the resolution of the NTP timestamp. The measurement uncertainty of the timestamp is not indicated as it may not be known. A sender that can keep track of elapsed time but has no notion of wallclock time may use the elapsed time since joining Schulzrinne, et al Standards Track [Page 24] RFC 1889 RTP January 1996 the session instead. This is assumed to be less than 68 years, so the high bit will be zero. It is permissible to use the sampling clock to estimate elapsed wallclock time. A sender that has no notion of wallclock or elapsed time may set the NTP timestamp to zero. RTP timestamp: 32 bits Corresponds to the same time as the NTP timestamp (above), but in the same units and with the same random offset as the RTP timestamps in data packets. This correspondence may be used for intra- and inter-media synchronization for sources whose NTP timestamps are synchronized, and may be used by media- independent receivers to estimate the nominal RTP clock frequency. Note that in most cases this timestamp will not be equal to the RTP timestamp in any adjacent data packet. Rather, it is calculated from the corresponding NTP timestamp using the relationship between the RTP timestamp counter and real time as maintained by periodically checking the wallclock time at a sampling instant. sender's packet count: 32 bits The total number of RTP data packets transmitted by the sender since starting transmission up until the time this SR packet was generated. The count is reset if the sender changes its ×××C identifier. sender's octet count: 32 bits The total number of payload octets (i.e., not including header or padding) transmitted in RTP data packets by the sender since starting transmission up until the time this SR packet was generated. The count is reset if the sender changes its ×××C identifier. This field can be used to estimate the average payload data rate. The third section contains zero or more reception report blocks depending on the number of other sources heard by this sender since the last report. Each reception report block conveys statistics on the reception of RTP packets from a single synchronization source. Receivers do not carry over statistics when a source changes its ×××C identifier due to a collision. These statistics are: ×××C_n (source identifier): 32 bits The ×××C identifier of the source to which the information in this reception report block pertains. fraction lost: 8 bits The fraction of RTP data packets from source ×××C_n lost since the previous SR or RR packet was sent, expressed as a fixed Schulzrinne, et al Standards Track [Page 25] RFC 1889 RTP January 1996 point number with the binary point at the left edge of the field. (That is equivalent to taking the integer part after multiplying the loss fraction by 256.) This fraction is defined to be the number of packets lost divided by the number of packets expected, as defined in the next paragraph. An implementation is shown in Appendix A.3. If the loss is negative due to duplicates, the fraction lost is set to zero. Note that a receiver cannot tell whether any packets were lost after the last one received, and that there will be no reception report block issued for a source if all packets from that source sent during the last reporting interval have been lost. cumulative number of packets lost: 24 bits The total number of RTP data packets from source ×××C_n that have been lost since the beginning of reception. This number is defined to be the number of packets expected less the number of packets actually received, where the number of packets received includes any which are late or duplicates. Thus packets that arrive late are not counted as lost, and the loss may be negative if there are duplicates. The number of packets expected is defined to be the extended last sequence number received, as defined next, less the initial sequence number received. This may be calculated as shown in Appendix A.3. extended highest sequence number received: 32 bits The low 16 bits contain the highest sequence number received in an RTP data packet from source ×××C_n, and the most significant 16 bits extend that sequence number with the corresponding count of sequence number cycles, which may be maintained according to the algorithm in Appendix A.1. Note that different receivers within the same session will generate different extensions to the sequence number if their start times differ significantly. interarrival jitter: 32 bits An estimate of the statistical variance of the RTP data packet interarrival time, measured in timestamp units and expressed as an unsigned integer. The interarrival jitter J is defined to be the mean deviation (smoothed absolute value) of the difference D in packet spacing at the receiver compared to the sender for a pair of packets. As shown in the equation below, this is equivalent to the difference in the "relative transit time" for the two packets; the relative transit time is the difference between a packet's RTP timestamp and the receiver's clock at the time of arrival, measured in the same units. Schulzrinne, et al Standards Track [Page 26] RFC 1889 RTP January 1996 If Si is the RTP timestamp from packet i, and Ri is the time of arrival in RTP timestamp units for packet i, then for two packets i and j, D may be expressed as D(i,j)=(Rj-Ri)-(Sj-Si)=(Rj-Sj)-(Ri-Si) The interarrival jitter is calculated continuously as each data packet i is received from source ×××C_n, using this difference D for that packet and the previous packet i-1 in order of arrival (not necessarily in sequence), according to the formula J=J+(|D(i-1,i)|-J)/16 Whenever a reception report is issued, the current value of J is sampled. The jitter calculation is prescribed here to allow profile- independent monitors to make valid interpretations of reports coming from different implementations. This algorithm is the optimal first- order estimator and the gain parameter 1/16 gives a good noise reduction ratio while maintaining a reasonable rate of convergence [11]. A sample implementation is shown in Appendix A.8. last SR timestamp (LSR): 32 bits The middle 32 bits out of 64 in the NTP timestamp (as explained in Section 4) received as part of the most recent RTCP sender report (SR) packet from source ×××C_n. If no SR has been received yet, the field is set to zero. delay since last SR (DLSR): 32 bits The delay, expressed in units of 1/65536 seconds, between receiving the last SR packet from source ×××C_n and sending this reception report block. If no SR packet has been received yet from ×××C_n, the DLSR field is set to zero. Let ×××C_r denote the receiver issuing this receiver report. Source ×××C_n can compute the round propagation delay to ×××C_r by recording the time A when this reception report block is received. It calculates the total round-trip time A-LSR using the last SR timestamp (LSR) field, and then subtracting this field to leave the round-trip propagation delay as (A- LSR - DLSR). This is illustrated in Fig. 2. This may be used as an approximate measure of distance to cluster receivers, although some links have very asymmetric delays. Schulzrinne, et al Standards Track [Page 27] RFC 1889 RTP January 1996 6.3.2 RR: Receiver report RTCP packet [10 Nov 1995 11:33:25.125] [10 Nov 1995 11:33:36.5] n SR(n) A=b710:8000 (46864.500 s) ----------------------------------------------------------------> v ^ ntp_sec =0xb44db705 v ^ dlsr=0x0005.4000 ( 5.250s) ntp_frac=0x20000000 v ^ lsr =0xb705:2000 (46853.125s) (3024992016.125 s) v ^ r v ^ RR(n) ----------------------------------------------------------------> |<-DLSR->| (5.250 s) A 0xb710:8000 (46864.500 s) DLSR -0x0005:4000 ( 5.250 s) LSR -0xb705:2000 (46853.125 s) ------------------------------- delay 0x 6:2000 ( 6.125 s) Figure 2: Example for round-trip time computation 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |V=2|P| RC | PT=RR=201 | length | header +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ×××C of packet sender | +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+ | ×××C_1 (×××C of first source) | report +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ block | fraction lost | cumulative number of packets lost | 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | extended highest sequence number received | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | interarrival jitter | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | last SR (LSR) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | delay since last SR (DLSR) | +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+ | ×××C_2 (×××C of second source) | report +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ block : ... : 2 +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+ | profile-specific extensions | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Schulzrinne, et al Standards Track [Page 28] RFC 1889 RTP January 1996 The format of the receiver report (RR) packet is the same as that of the SR packet except that the packet type field contains the constant 201 and the five words of sender information are omitted (these are the NTP and RTP timestamps and sender's packet and octet counts). The remaining fields have the same meaning as for the SR packet. An empty RR packet (RC = 0) is put at the head of a compound RTCP packet when there is no data transmission or reception to report. 6.3.3 Extending the sender and receiver reports A profile should define profile- or application-specific extensions to the sender report and receiver if there is additional information that should be reported regularly about the sender or receivers. This method should be used in preference to defining another RTCP packet type because it requires less overhead: o fewer octets in the packet (no RTCP header or ×××C field); o simpler and faster parsing because applications running under that profile would be programmed to always expect the extension fields in the directly accessible location after the reception reports. If additional sender information is required, it should be included first in the extension for sender reports, but would not be present in receiver reports. If information about receivers is to be included, that data may be structured as an array of blocks parallel to the existing array of reception report blocks; that is, the number of blocks would be indicated by the RC field. 6.3.4 Analyzing sender and receiver reports It is expected that reception quality feedback will be useful not only for the sender but also for other receivers and third-party monitors. The sender may modify its transmissions based on the feedback; receivers can determine whether problems are local, regional or global; network managers may use profile-independent monitors that receive only the RTCP packets and not the corresponding RTP data packets to evaluate the performance of their networks for multicast distribution. Cumulative counts are used in both the sender information and receiver report blocks so that differences may be calculated between any two reports to make measurements over both short and long time periods, and to provide resilience against the loss of a report. The difference between the last two reports received can be used to estimate the recent quality of the distribution. The NTP timestamp is
转载于:https://blog.51cto.com/leizhong/1657625
2163
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
