MPLS L3××× + 静态路由配置
关键词： MSR;MPLS;BGP;×××; 静态路由
一、组网需求：
2台PE各接着一个***a的站点，PEA连接***a站点1出口CEA，PEA与CEA通过静态路由访问CEA下挂站点
设备清单：MSR系列路由器3台
二、组网图：
6365.jpg
三、配置步骤：
适用设备和版本：MSR系列、Version 5.20, Beta 1105后所有版本。
CEA配置：
interface Ethernet0/0
port link-mode route
ip address 192.168.0.2 255.255.255.0
#
interface Ethernet0/1
port link-mode route
ip address 192.168.1.1 255.255.255.0
#
ip route-static 0.0.0.0 0.0.0.0 192.168.0.1
#
PEA配置：
router id 1.1.1.1
#
ip ***-instance ***a
route-distinguisher 1:1
***-target 1:1 export-extcommunity
***-target 1:1 import-extcommunity
#
mpls lsr-id 1.1.1.1
#
mpls
#
mpls ldp
#
interface Ethernet0/0
port link-mode route
ip address 1.2.0.1 255.255.255.0
mpls
mpls ldp
#
interface Ethernet0/1
port link-mode route
ip binding ***-instance ***a
ip address 192.168.0.1 255.255.255.0
#
interface LoopBack0
ip address 1.1.1.1 255.255.255.255
#
bgp 1
undo synchronization
group 1 internal
peer 1 connect-interface LoopBack0
peer 2.2.2.2 group 1
#
ipv4-family ***v4
peer 1 enable
peer 2.2.2.2 enable
peer 2.2.2.2 group 1
#
ipv4-family ***-instance ***a
network 192.168.0.0
import-route static
#
ospf 1
area 0.0.0.0
network 1.1.1.1 0.0.0.0
network 1.2.0.0 0.0.0.255
#
ip route-static ***-instance ***a 192.168.1.0 255.255.255.0 192.168.0.2
#
PEB配置：
#
router id 2.2.2.2
#
ip ***-instance ***a
route-distinguisher 2:1
***-target 1:1 export-extcommunity
***-target 1:1 import-extcommunity
#
mpls lsr-id 2.2.2.2
#
mpls
#
mpls ldp
#
interface Ethernet0/0
port link-mode route
ip address 1.2.0.2 255.255.255.0
mpls
mpls ldp
#
interface Ethernet0/1
port link-mode route
ip binding ***-instance ***a
ip address 172.32.0.1 255.255.255.0
#
interface LoopBack0
ip address 2.2.2.2 255.255.255.255
#
bgp 1
undo synchronization
peer 1.1.1.1 as-number 1
peer 1.1.1.1 connect-interface LoopBack0
#
ipv4-family ***v4
peer 1.1.1.1 enable
#
ipv4-family ***-instance ***a
import-route direct
#
ospf 1
area 0.0.0.0
network 2.2.2.2 0.0.0.0
network 1.2.0.0 0.0.0.255
#
四、配置关键点：
1.      CEA上需要配置访问其他***路由的静态路由；
2.      PEA上需要配置访问CEA下挂***a站点1的静态路由
3.      PEA的BGP要引入静态***a路由。