HA:high availability
1、设备的容错和可靠性
2、设备和链路、模块冗余
MSFC:路由器的处理引擎
PFC:交换机的处理引擎
RPR,是引擎板卡切换的一种机制
1、vlan datebase不被支持
2、snmp改变不能被同步
3、无镜像或负载均衡
4、同一时间只有一个引擎起作用
5、必须同样的IOS版本
6、FIB表在切换的时候被清除,路由流量被切断
7、静态路由可以切换
8、动态信息不回被同步,切换时会丢失
命令:
redundacy
mode rpr-plus
show redundancy states
SRM with SSO、NSF with SSO,这些切换很简单,速度很快,比较高级
power redundancy-mode combined /redundant
show power
代理ARP:
1、PC不用配网关
2、解决了冗余备份需求
预配:
R1:
interface s1/0
ip address 12.1.1.1 255.255.255.0
no shut
interface s1/1
ip address 13.1.1.1 255.255.255.0
no shut
interface lo0
ip address 1.1.1.1 255.255.255.0
no shut
router rip
version 2
no auto-summary
network 12.0.0.0
network 13.0.0.0
network 1.0.0.0
R2:
interface s1/0
ip address 12.1.1.2 255.255.255.0
no shut
interface f0/0
ip address 23.1.1.2 255.255.255.0
no shut
router rip
version 2
no auto-summary
network 12.0.0.0
network 23.0.0.0
R3:
interfac s1/1
ip address 13.1.1.3 255.255.255.0
no shut
interface f0/0
ip address 23.1.1.3 255.255.255.0
no shut
router rip
version 2
no auto-summary
network 13.0.0.0
network 23.0.0.0
R4:
interface f0/0
ip address 23.1.1.4 255.255.255.0
no shut
no ip routing
配置结束,proxy arp和icmp redirects默认是开启的
在R2,R3,R4上开启 debug arp
当直连down掉后,是通过ARP代理来切换的,而PC4是个路由器,它的ARP默认老化时间是4个小时
也就是需要等4个小时后才能切换过来
上行链路down掉后,切换的时间就是IGP路由的收敛时间
IRDP:只是解决了PC不配网关的问题,通过发送icmp报文,icmp routing
边界网关主动发送报文,先比较优先级,后比较IP,地址大的
interface ip irdp
ip irdp preference 设置优先级
HSRP:推荐在思科设备上用
通过HSRP来选举active router和standby router
而PC网关的IP是虚拟的IP,在设备上配置的VIP,对应有VMAC地址
0000.0c0u.ac最后字节就是组号,前面MAC字段就是虚拟MAC的前缀字段
发送hello包,目的地址是224.0.0.2
先比高的优先级
再比高的IP地址
HSRP states
1、initial
2、learn 学习VIP,standby路由器可以不配,因为可以通过hello学习到
3、listen
4、speak 发送hello包
5、standy
6、active
VRRP:组播报文224.0.0.18
GLBP:每3秒发一次 224.0.0.108 基于UDP 3222端口
转载于:https://blog.51cto.com/867645/1357912