NA-NP-IE系列实验51: 三层交换实现VLAN 间路由

实验51:  三层交换实现VLAN 间路由

1.  实验目的

通过本实验，读者可以掌握如下技能：

（1） 理解三层交换的概念

（2） 配置三层交换

2.  实验拓扑

拓扑图

3.  实验步骤

注：用SW1 来实现分别处于VLAN1 和VLAN2 的PC0 和PC1 间的通信。

要在三层交换机上启用路由功能，还需要启用CEF（命令为：ip cef），不过这是

默认值。和路由器一样，三层交换机上同样可以运行路由协议。

 

 

 

sw1#vlan da

% Warning: It is recommended to configure VLAN from config mode,

  as VLAN database mode is being deprecated. Please consult user

  documentation for configuring VTP/VLAN in config mode.

 

sw1(vlan)#vlan 2 name cisco

VLAN 2 added:

    Name: cisco

sw1(vlan)#exit

APPLY completed.

Exiting....

sw1#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

sw1(config)#int vlan  1

sw1(config-if)#ip add 172.16.1.1 255.255.255.0//在vlan 接口上配置IP 地址即可，VLAN 1 接口上的地址就是PC0 的网关了，VLAN 2 接口上的地址就是PC1的网关了。

 

sw1(config-if)#no sh

 

%LINK-5-CHANGED: Interface Vlan1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up

sw1(config-if)#

sw1(config-if)#exit

sw1(config)#int vlan 2

 

%LINK-5-CHANGED: Interface Vlan2, changed state to upsw1(config-if)#

sw1(config-if)#ip add 172.16.2.1 255.255.255.0

sw1(config-if)#no sh

sw1(config-if)#exit

sw1(config)#int f0/2

sw1(config-if)#switch mode access

sw1(config-if)#switch access vlan 2

 

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to upsw1(config-if)#

sw1(config-if)#exit

sw1(config)#ip routing//以上开启SW1 的路由功能，这时SW1 就启用了三层功能。

sw1(config)#

sw1(config)#do sh ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

       * - candidate default, U - per-user static route, o - ODR

       P - periodic downloaded static route

 

Gateway of last resort is not set

 

     172.16.0.0/24 is subnetted, 2 subnets

C       172.16.1.0 is directly connected, Vlan1

C       172.16.2.0 is directly connected, Vlan2

//和路由器一样，三层交换机上也有路由表。

 

 

PC0:

PC>ipconfig

 

IP Address......................: 172.16.1.2

Subnet Mask.....................: 255.255.255.0

Default Gateway.................: 172.16.1.1

 

PC>ping 172.16.2.2

 

Pinging 172.16.2.2 with 32 bytes of data:

 

Reply from 172.16.2.2: bytes=32 time=109ms TTL=127

Reply from 172.16.2.2: bytes=32 time=62ms TTL=127

Reply from 172.16.2.2: bytes=32 time=63ms TTL=127

Reply from 172.16.2.2: bytes=32 time=63ms TTL=127

 

Ping statistics for 172.16.2.2:

    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

    Minimum = 62ms, Maximum = 109ms, Average = 74ms

 

PC>

 

 

PC1:

PC>ipconfig

 

IP Address......................: 172.16.2.2

Subnet Mask.....................: 255.255.255.0

Default Gateway.................: 172.16.2.1

 

PC>ping 172.16.1.2

 

Pinging 172.16.1.2 with 32 bytes of data:

 

Reply from 172.16.1.2: bytes=32 time=62ms TTL=127

Reply from 172.16.1.2: bytes=32 time=62ms TTL=127

Reply from 172.16.1.2: bytes=32 time=62ms TTL=127

Reply from 172.16.1.2: bytes=32 time=62ms TTL=127

 

Ping statistics for 172.16.1.2:

    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

    Minimum = 62ms, Maximum = 62ms, Average = 62ms

 

PC>

本文转自gauyanm 51CTO博客，原文链接：http://blog.51cto.com/gauyanm/245116，如需转载请自行联系原作者