linux 内存 boot,用于U-boot的Linux内核的内存位置

最新推荐文章于 2024-08-19 19:54:51 发布

跑马溜溜

最新推荐文章于 2024-08-19 19:54:51 发布

阅读量332

点赞数

文章标签： linux 内存 boot

目前,我有一个ARM设备,它使用U-boot来加载Android操作系统。我想用Linux取代Android。所以我所做的是将为ARM设备编译的Linux副本加载到SD卡上,引导到U-boot bootloader。现在的问题是,我应该告诉U-boot什么内存位置来启动vmlinuz Linux内核?

我怎么知道?或者指出一些资源也是很好的。

谢谢。

以下是从连接到串行端口的当前启动顺序

Reg Version: v1.1.0

Reg Time: 2014-10-115:15:35

Reg Name: hi3719cdmo1a_hi3719cv100_ddr3_1gbyte_16bitx2_2layers_emmc.reg

Fastboot 3.3.0 (zengzhiliang@server180) (Nov 21 2014 - 13:41:16)

Fastboot: Version 3.3.0

Build Date: Nov 21 2014, 13:41:29

CPU: Hi3719Cv100

Boot Media: eMMC

DDR Size: 1GB

Check nand flash controller v610. found

Special NAND id table Version 1.36

Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00

No NAND device found!!!

Check spi flash controller v350. found

Can't find a valid spi flash chip.

MMC/SD controller initialization.

MMC/SD Card:

MID: 0xfe

Read Block: 512 Bytes

Write Block: 512 Bytes

Chip Size: 3656M Bytes (High Capacity)

Name: "P1XXX"

Chip Type: MMC

Version: 4.0

Speed: 25000000Hz

Bus Width: 8bit

Boot Addr: 0 Bytes

*** Warning - bad CRC or eMMC, using default environment

Boot Env on eMMC

Env Offset: 0x00100000

Env Size: 0x00010000

Env Range: 0x00010000

SDK Version: HiSTBAndroidV500R001C01CP0002_v2014070614

[Android_Main,34] begin

[sw_set_gpio,85] ok

[sw_ptable_init,66] begin

partition addr : [0x200000]

[swfastboot_flash_read,31]BaseAddress:0x200000, DataSize:0x100000, offset:0x0, b ytes:0xa10

[sw_ptable_check,176]cksum [0x6c94], ptable->checksum[0x6c94]

[sw_ptable_init,79] data at 0x200000 is ok

0 fastboot 0x00000000 0x00200000

1 partition 0x00200000 0x00200000

2 recovery 0x00400000 0x01000000

3 deviceinfo 0x01400000 0x00200000

4 baseparam 0x01600000 0x00800000

5 pqparam 0x01E00000 0x00800000

6 logo 0x02600000 0x00800000

7 fastplay 0x02E00000 0x02800000

8 boot 0x05600000 0x01000000

9 misc 0x06600000 0x00200000

10 system 0x06800000 0x27000000

11 cache 0x2D800000 0x19000000

12 backup 0x46800000 0x19000000

13 swdb 0x5F800000 0x03000000

14 userdata 0x62800000 0x80000000

ptable info:2M(fastboot),2M(partition),16M(recovery),2M(deviceinfo),8M(baseparam ),8M(pqparam),8M(logo),40M(fastplay),16M(boot),2M(misc),624M(system),400M(cache) ,400M(backup),48M(swdb),2048M(userdata)

[sw_ptable_init,104] ok

[sw_devinfo_init,25] begin

deviceinfo addr : [0x01400000]

[swfastboot_flash_read,31]BaseAddress:0x1400000, DataSize:0x100000, offset:0x0, bytes:0x514

[sw_devinfo_check,166] start...

[sw_devinfo_check,184] ok,checksum:0x9aad

[sw_devinfo_init,44] data at 0x1400000 is ok

[0] count:[4] name:[serialno] value:[STBHUWEC1505047662]

[1] count:[4] name:[mac] value:[00:07:63:f4:d3:12]

[2] count:[4] name:[standard] value:[1080i_50Hz]

[3] count:[4] name:[secureline] value:[20100]

[sw_devinfo_init,71] ok

[swfastboot_flash_read,31]BaseAddress:0x6600000, DataSize:0x100000, offset:0x0, bytes:0x10000

boot normal!!!

[swfastboot_flash_read,31]BaseAddress:0x5602000, DataSize:0x100000, offset:0x0, bytes:0x2000

use boot cmdline,disable serial, cmdline:[mem=1G console=NULL,115200 blkdevparts =mmcblk0:]

bootargs:[mem=1G console=NULL,115200 blkdevparts=mmcblk0:2M(fastboot),2M(partiti on),16M(recovery),2M(deviceinfo),8M(baseparam),8M(pqparam),8M(logo),40M(fastplay ),16M(boot),2M(misc),624M(system),400M(cache),400M(backup),48M(swdb),2048M(userd ata) androidboot.mac=00:07:63:f4:d3:12 androidboot.standard=1080i_50Hz androidbo ot.serialno=STBHUWEC1505047662]

authenticat kernel begin

CA_GetFlashImgInfoByAddr,683: Img has already be encrypted

CA_GetFlashImgInfoByAddr,689: Magic number check right

CA_FlashAuthenticateByAddr,898: CA_FlashAuthenticateByAddr 0x5600000 successe d

offset = 0x5600000 KernelImgInDDRAddress = 0x4002000bootimg now: bootm 4002000

[Android_Main,52] ok

stDispParam.enFormat = 6

sw_EdidAll[0] = 10

sw_EdidAll[1] = 5

sw_EdidAll[2] = 9

sw_EdidAll[3] = 8

sw_EdidAll[4] = 7