linux 4.9.166 内核,Solved: Re: NFS Hangs with linux 4.9.166 on IMX6Q - NXP Community

Hi, thanks for your reply.

In fact, I am building my own kernel with buildroot with based on the apalis-imx6q defconfig. I was able to connect to my board in tftp/nfs when I used linux 3.14.52 (that I also built on my own with buildroot). So, I don't think the problem is on the server part of the nfs connection. The boot of the card processor give me that :

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

[ 0.000000] Booting Linux on physical CPU 0x0

[ 0.000000] Linux version 4.9.166 (alexis@Fronteau-Ubuntu) (gcc version 5.4.0 (Buildroot 2017.02.1-00152-gabdcf8fa6-dirty) ) #8 SMP Fri May 31 10:20:42 CEST 2019

[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d

[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache

[ 0.000000] OF: fdt:Machine model: Imajbox W with Apalis module

[ 0.000000] bootconsole [earlycon0] enabled

[ 0.000000] Reserved memory: created CMA memory pool at 0x38000000, size 320 MiB

[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool

[ 0.000000] Memory policy: Data cache writealloc

[ 0.000000] percpu: Embedded 14 pages/cpu @bf6f4000 s25612 r8192 d23540 u57344

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096

[ 0.000000] Kernel command line: enable_wait_mode=off vmalloc=400M ip=dhcp root=/dev/nfs nfsroot=192.168.1.211:/home/data/Workspace/ImajboxV2/Software/PlatformW/trunk/devenv/new_kernel/nfsroot rw fec_mac=00:14

:2d:49:e7:09 consoleblank=0 no_console_suspend=1 console=ttymxc0,115200n8 earlyprintk

[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

[ 0.000000] Memory: 698736K/1048576K available (8192K kernel code, 365K rwdata, 1888K rodata, 1024K init, 413K bss, 22160K reserved, 327680K cma-reserved, 0K highmem)

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)

[ 0.000000] vmalloc : 0xc0800000 - 0xff800000 (1008 MB)

[ 0.000000] lowmem : 0x80000000 - 0xc0000000 (1024 MB)

[ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)

[ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB)

[ 0.000000] .text : 0x80008000 - 0x80900000 (9184 kB)

[ 0.000000] .init : 0x80b00000 - 0x80c00000 (1024 kB)

[ 0.000000] .data : 0x80c00000 - 0x80c5b760 ( 366 kB)

[ 0.000000] .bss : 0x80c5b760 - 0x80cc2dac ( 414 kB)

[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1

[ 0.000000] Hierarchical RCU implementation.

[ 0.000000] Build-time adjustment of leaf fanout to 32.

[ 0.000000] NR_IRQS:16 nr_irqs:16 16

[ 0.000000] L2C: DT/platform modifies aux control register: 0x32070000 -> 0x32470000

[ 0.000000] L2C-310 errata 752271 769419 enabled

[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9

[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9

[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines

[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled

[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB

[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001

[ 0.000000] Switching to timer-based delay loop, resolution 333ns

[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns

[ 0.008297] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns

[ 0.019641] Console: colour dummy device 80x30

[ 0.024204] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)

[ 0.034511] pid_max: default: 32768 minimum: 301

[ 0.039315] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.046048] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.053850] CPU: Testing write buffer coherency: ok

[ 0.058855] CPU0: Spectre v2: using BPIALL workaround

[ 0.064356] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000

[ 0.070176] Setting up static identity map for 0x10100000 - 0x10100058

[ 0.079009] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001

[ 0.079015] CPU1: Spectre v2: using BPIALL workaround

[ 0.090821] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002

[ 0.090827] CPU2: Spectre v2: using BPIALL workaround

[ 0.102610] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003

[ 0.102616] CPU3: Spectre v2: using BPIALL workaround

[ 0.113623] Brought up 4 CPUs

[ 0.116689] SMP: Total of 4 processors activated (24.00 BogoMIPS).

[ 0.122970] CPU: All CPU(s) started in SVC mode.

[ 0.128581] devtmpfs: initialized

[ 0.146281] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4

[ 0.154375] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns

[ 0.164338] futex hash table entries: 1024 (order: 4, 65536 bytes)

[ 0.187204] pinctrl core: initialized pinctrl subsystem

[ 0.193690] NET: Registered protocol family 16

[ 0.205784] DMA: preallocated 256 KiB pool for atomic coherent allocations

[ 0.243392] cpuidle: using governor menu

[ 0.247622] CPU identified as i.MX6Q, silicon rev 1.5

[ 0.274203] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.

[ 0.282317] hw-breakpoint: maximum watchpoint size is 4 bytes.

[ 0.288697] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/leds_platformw

[ 0.300051] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/gpssensor

[ 0.310960] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/imusensor

[ 0.321868] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/smartbattery

[ 0.333035] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/imajboxcharger

[ 0.344375] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/video

[ 0.354934] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/pps

[ 0.365319] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/keys_platformw

[ 0.376659] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/platformwgpio

[ 0.387911] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/powercontrol

[ 0.399078] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/pwrregulator

[ 0.410244] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/uart1

[ 0.420802] imx6q-pinctrl 20e0000.iomuxc: no fsl,pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/uart2

[ 0.431609] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver

[ 0.440001] imx-gpc 20dc000.gpc: no fsl,ldo-bypass found!

[ 0.445647] imx-gpc 20dc000.gpc: Registered imx-gpc

[ 0.475620] vgaarb: loaded

[ 0.478739] SCSI subsystem initialized

[ 0.483037] usbcore: registered new interface driver usbfs

[ 0.488709] usbcore: registered new interface driver hub

[ 0.494216] usbcore: registered new device driver usb

[ 0.500504] i2c i2c-1: IMX I2C adapter registered

[ 0.505337] i2c i2c-1: can't use DMA, using PIO instead.

[ 0.514051] stmpe-i2c 2-0041: stmpe811 detected, chip id: 0x811

[ 0.604351] i2c i2c-2: IMX I2C adapter registered

[ 0.609163] i2c i2c-2: can't use DMA, using PIO instead.

[ 0.615004] i2c i2c-3: IMX I2C adapter registered

[ 0.619816] i2c i2c-3: can't use DMA, using PIO instead.

[ 0.625397] Linux video capture interface: v2.00

[ 0.630150] pps_core: LinuxPPS API ver. 1 registered

[ 0.635229] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti

[ 0.644501] PTP clock support registered

[ 0.673452] imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)

[ 0.703443] imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)

[ 0.711943] mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed ipu0 csi0

[ 0.719645] mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a

[ 0.727672] MIPI CSI2 driver module loaded

[ 0.733094] clocksource: Switched to clocksource mxc_timer1

[ 0.738901] VFS: Disk quotas dquot_6.6.0

[ 0.742974] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[ 0.760565] NET: Registered protocol family 2

[ 0.765658] TCP established hash table entries: 8192 (order: 3, 32768 bytes)

[ 0.772892] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)

[ 0.779588] TCP: Hash tables configured (established 8192 bind 8192)

[ 0.786221] UDP hash table entries: 512 (order: 2, 16384 bytes)

[ 0.792275] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)

[ 0.798918] NET: Registered protocol family 1

[ 0.803919] RPC: Registered named UNIX socket transport module.

[ 0.809944] RPC: Registered udp transport module.

[ 0.814773] RPC: Registered tcp transport module.

[ 0.819576] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 0.826792] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available

[ 0.836542] Bus freq driver module loaded

[ 0.842468] workingset: timestamp_bits=30 max_order=18 bucket_order=0

[ 0.855730] NFS: Registering the id_resolver key type

[ 0.860897] Key type id_resolver registered

[ 0.865236] Key type id_legacy registered

[ 0.869355] nfs4filelayout_init: NFSv4 File Layout Driver Registering...

[ 0.876815] ntfs: driver 2.1.32 [Flags: R/W].

[ 0.881578] fuse init (API version 7.26)

[ 0.892693] io scheduler noop registered

[ 0.896749] io scheduler deadline registered

[ 0.901291] io scheduler cfq registered (default)

[ 0.907126] imx-pcie 1ffc000.pcie: no reserved region node.

[ 0.912863] 1ffc000.pcie supply epdev_on not found, using dummy regulator

[ 0.920075] OF: PCI: host bridge /soc/pcie@0x01000000 ranges:

[ 0.925962] OF: PCI: IO 0x01f80000..0x01f8ffff -> 0x00000000

[ 0.931994] OF: PCI: MEM 0x01000000..0x01efffff -> 0x01000000

[ 1.072893] imx-pcie 1ffc000.pcie: Link: Gen2 disabled

[ 1.078150] imx-pcie 1ffc000.pcie: Link up, Gen1

[ 1.083256] imx-pcie 1ffc000.pcie: PCI host bridge to bus 0000:00

[ 1.089461] pci_bus 0000:00: root bus resource [bus 00-ff]

[ 1.095070] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]

[ 1.101355] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]

[ 1.108754] PCI: bus0: Fast back to back transfers disabled

[ 1.143217] PCI: bus1: Fast back to back transfers disabled

[ 1.149074] pci 0000:00:00.0: BAR 0: assigned [mem 0x01000000-0x010fffff]

[ 1.156000] pci 0000:00:00.0: BAR 8: assigned [mem 0x01100000-0x011fffff]

[ 1.162898] pci 0000:00:00.0: BAR 6: assigned [mem 0x01200000-0x0120ffff pref]

[ 1.170250] pci 0000:01:00.0: BAR 0: assigned [mem 0x01100000-0x0110ffff 64bit]

[ 1.177739] pci 0000:01:00.0: BAR 2: assigned [mem 0x01110000-0x01111fff 64bit]

[ 1.185228] pci 0000:00:00.0: PCI bridge to [bus 01-ff]

[ 1.190561] pci 0000:00:00.0: bridge window [mem 0x01100000-0x011fffff]

[ 1.197707] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt

[ 1.204799] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt

[ 1.211747] pci 0000:01:00.0: enabling device (0140 -> 0142)

[ 1.220993] imx-sdma 20ec000.sdma: no iram assigned, using external mem

[ 1.228068] imx-sdma 20ec000.sdma: loaded firmware 3.3

[ 1.238007] pfuze100-regulator 2-0008: Full layer: 1, Metal layer: 1

[ 1.245202] pfuze100-regulator 2-0008: FAB: 0, FIN: 0

[ 1.250358] pfuze100-regulator 2-0008: pfuze100 found.

[ 1.278292] imx6q-pinctrl 20e0000.iomuxc: unable to find group for node uart1grp-dtenoctlr

[ 1.286703] imx-uart: probe of 2020000.serial failed with error -22

[ 1.293343] imx6q-pinctrl 20e0000.iomuxc: unable to find group for node uart2grp-dtenoctlr

[ 1.301720] imx-uart: probe of 21e8000.serial failed with error -22

[ 1.308443] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 69, base_baud = 5000000) is a IMX

[ 1.317765] 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 70, base_baud = 5000000) is a IMX

[ 1.327401] [drm] Initialized

[ 1.330881] [drm] Initialized vivante 1.0.0 20120216 on minor 0

[ 1.348165] brd: module loaded

[ 1.358685] loop: module loaded

[ 1.384957] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024

[ 1.392988] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480

[ 1.401142] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000

[ 1.409447] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000

[ 1.420679] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled

[ 1.427799] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode

[ 1.436723] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst

[ 1.447333] scsi host0: ahci-imx

[ 1.450983] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77

[ 1.460628] spi_imx 2008000.ecspi: probed

[ 1.465708] spi_imx 200c000.ecspi: probed

[ 1.470514] libphy: Fixed MDIO Bus: probed

[ 1.475144] vcan: Virtual CAN interface driver

[ 1.479689] CAN device driver interface

[ 1.484820] 2188000.ethernet supply phy not found, using dummy regulator

[ 1.503171] pps pps0: new PPS source ptp0

[ 1.508434] libphy: fec_enet_mii_bus: probed

[ 1.514518] fec 2188000.ethernet eth0: registered PHC device 0

[ 1.520820] usbcore: registered new interface driver asix

[ 1.526399] usbcore: registered new interface driver ax88179_178a

[ 1.532644] usbcore: registered new interface driver cdc_ether

[ 1.538642] usbcore: registered new interface driver net1080

[ 1.544457] usbcore: registered new interface driver cdc_subset

[ 1.550515] usbcore: registered new interface driver zaurus

[ 1.556268] usbcore: registered new interface driver cdc_ncm

[ 1.562028] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 1.568670] ehci-pci: EHCI PCI platform driver

[ 1.573277] ehci-mxc: Freescale On-Chip EHCI Host driver

[ 1.578854] usbcore: registered new interface driver usb-storage

[ 1.585093] usbcore: registered new interface driver usbserial

[ 1.591063] usbcore: registered new interface driver usbserial_generic

[ 1.597749] usbserial: USB Serial support registered for generic

[ 1.603909] usbcore: registered new interface driver ftdi_sio

[ 1.609786] usbserial: USB Serial support registered for FTDI USB Serial Device

[ 1.617252] usbcore: registered new interface driver pl2303

[ 1.622958] usbserial: USB Serial support registered for pl2303

[ 1.630099] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator

[ 1.638873] mousedev: PS/2 mouse device common for all mice

[ 1.654811] input: stmpe-ts as /devices/soc0/soc/2100000.aips-bus/21a4000.i2c/i2c-2/2-0041/stmpe-ts/input/input0

[ 1.666214] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc0

[ 1.675152] i2c /dev entries driver

[ 1.680731] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)

[ 1.687267] sdhci: Secure Digital Host Controller Interface driver

[ 1.693571] sdhci: Copyright(c) Pierre Ossman

[ 1.698025] sdhci-pltfm: SDHCI platform and OF driver helper

[ 1.704766] sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode

[ 1.773132] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA

[ 1.786978] mxc_vpu 2040000.vpu_fsl: VPU initialized

[ 1.792498] mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed

[ 1.801842] Galcore version 6.2.4.150331

[ 1.953282] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)

[ 1.960705] ata1.00: ATA-9: TS128GMTS400, O0918B, max UDMA/133

[ 1.966754] ata1.00: 250069680 sectors, multi 1: LBA48 NCQ (depth 31/32)

[ 1.974527] ata1.00: configured for UDMA/133

[ 1.979941] scsi 0:0:0:0: Direct-Access ATA TS128GMTS400 8B PQ: 0 ANSI: 5

[ 2.542326] imx6q-pinctrl 20e0000.iomuxc: unable to find group for node leds-platformw

[ 2.550384] leds-gpio: probe of leds failed with error -22

[ 2.557086] caam 2100000.caam: ERA source: CAAMVID.

[ 2.562113] caam 2100000.caam: AXI pipeline throttling enabled.

[ 2.567355] mmc0: new DDR MMC card at address 0001

[ 2.567969] mmcblk0: mmc0:0001 004GE0 3.69 GiB

[ 2.568290] mmcblk0boot0: mmc0:0001 004GE0 partition 1 2.00 MiB

[ 2.568563] mmcblk0boot1: mmc0:0001 004GE0 partition 2 2.00 MiB

[ 2.569870] mmcblk0: p1 p2 p3

[ 2.593865] caam 2100000.caam: device ID = 0x0a16010000000000 (Era 4)

[ 2.593865] job rings = 2, qi = 0

[ 2.606444] caam_jr 2101000.jr0: Entropy delay = 3200

[ 2.611632] caam_jr 2101000.jr0: Instantiated RNG4 SH0.

[ 2.617730] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)

[ 2.625639] sd 0:0:0:0: [sda] Write Protect is off

[ 2.630640] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[ 2.639950] sd 0:0:0:0: [sda] Optimal transfer size 0 bytes < PAGE_SIZE (4096 bytes)

[ 2.649882] sda: sda1

[ 2.653507] sd 0:0:0:0: [sda] Attached SCSI disk

[ 2.672392] caam_jr 2101000.jr0: Instantiated RNG4 SH1.

[ 2.684905] caam algorithms registered in /proc/crypto

[ 2.694075] caam_jr 2101000.jr0: registering rng-caam

[ 2.700313] caam-snvs 20cc000.caam-snvs: can't get snvs clock

[ 2.706239] caam-snvs 20cc000.caam-snvs: violation handlers armed - non-secure state

[ 2.714311] hidraw: raw HID events driver (C) Jiri Kosina

[ 2.719967] usbcore: registered new interface driver usbhid

[ 2.725657] usbhid: USB HID core driver

[ 2.730671] random: fast init done

[ 2.739346] stmpe-adc stmpe-adc: Initialized

[ 2.744301] ip_tables: (C) 2000-2006 Netfilter Core Team

[ 2.750288] NET: Registered protocol family 10

[ 2.755773] ip6_tables: (C) 2000-2006 Netfilter Core Team

[ 2.761341] NET: Registered protocol family 17

[ 2.766005] can: controller area network core (rev 20120528 abi 9)

[ 2.772479] NET: Registered protocol family 29

[ 2.777043] can: raw protocol (rev 20120528)

[ 2.781411] can: broadcast manager protocol (rev 20161123 t)

[ 2.787193] can: netlink gateway (rev 20130117) max_hops=1

[ 2.793129] Key type dns_resolver registered

[ 2.799650] cpu cpu0: Registered imx6q-cpufreq

[ 2.804269] Registering SWP/SWPB emulation handler

[ 2.820317] imx_thermal 2000000.aips-bus:tempmon: Extended Commercial CPU temperature grade - max:105C critical:105C passive:95C

[ 2.832861] imx6q-pinctrl 20e0000.iomuxc: unable to find group for node keys-platformw

[ 2.840953] gpio-keys: probe of gpio-keys failed with error -22

[ 2.847101] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-15 05:11:02 UTC (1228262)

[ 2.955658] Micrel KSZ9031 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=110)

[ 2.970399] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[ 11.921386] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx

[ 11.943235] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

[ 11.973174] Sending DHCP requests ., OK

[ 12.053150] IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.194

[ 12.061011] IP-Config: Complete:

[ 12.064406] device=eth0, hwaddr=00:14:2d:49:e7:09, ipaddr=192.168.1.194, mask=255.255.255.0, gw=192.168.1.1

[ 12.074736] host=192.168.1.194, domain=imajing, nis-domain=(none)

[ 12.081379] bootserver=0.0.0.0, rootserver=192.168.1.211, rootpath= nameserver0=192.168.1.1

... then it hangs indefinitely, I can not be sure that is a NFS problem but when I used the old linux, it mount the NFS after this part.