php故障,电脑系统出了故障不显示PHP怎么处理

HP的错误号0xc18a0301上打印机

遵循以下步骤在面板上的一体打印机:：

A. -按下并按住“打印照片”和“消除红眼”按钮。放开两个按钮。应该说是“输入特殊键组合”

B. -按下和释放序列“红眼去除”，“打印照片”，

说：“红眼消除” 显示“输入一些特殊的组合键”

按下和释放序列“红眼去除”，“打印照片”，“消除红眼“ 如果“的支持COxxFN0723BR”与“uiaux”消息出现，请执行以下步骤： 2。按下并松开右侧的箭头按钮，直到显示“系统配置菜单”。(C8100采用触摸屏) 3。按下并松开“OK”按钮。 4。应该说是“硬件故障状态”。如果不存在的话，用箭头键切换到“硬件故障状态。 5。按下并松开“OK”按钮 。应该说是“硬件故障状态：清除。按“确定”清除“。 7。按下并松开“OK”按钮。邮件更改为“硬件故障状态清除。按“取消”继续。“ 8。“取消”按钮，根据需要多次按下并释放，这样一来，无论是“欢迎PHOTOSMART快速”的画面出现，或“墨水系统故障”的画面出现。请不要尝试打印在这个阶段。 9。使用电源按钮，打开本机的电源，拔掉电源线从打印机的背面和墙上的电源插座。 10。等待30秒放电电源，然后将电源线插入墙上的电源插座，然后到后面的打印机 11。打开本机。打印机可能会显示消息“使用电源按钮关机”，按OK键继续“打印机”。按“确定”。 12。如果打印机已经初始化，然后进入下一个步骤。如果没有，则打印机将开始“ONE TIME INK初始化过程”。允许此过程完成，不要打断。一旦初始化过程完成后，打印机将打印出诊断页。 13。要验证打印机功能打印自检页。

Follow the below steps on the front panel of the All-in-One printer:

A. - Press and Hold the “Print Photos” & “Red Eye Removal” buttons. Release both buttons. Display should say “Enter Special Key Combo”

B. - Press and release in sequence “Red Eye Removal”, “Print Photos”, “Red Eye Removal”

Display says "enter special key combo"

Press and release in sequence “Red Eye Removal”, “Print Photos”, “Red Eye Removal” .

If "support COxxFN0723BR" appears with "uiaux" message, perform the below steps:

2. Press and release the right arrow button until the display says “System Configuration Menu”. (on C8100 use Touch Screen)

3. Press and release the “OK” button.

4. Display should say “Hardware failure status”. If not there already, Arrow Key over to “Hardware failure status.

5. Press and release the “OK” button

6. Display should say “Hardware failure status: Clear. Press OK to clear”.

7. Press and release the “OK” Button. Message changes to “Hardware failure status Cleared. Press Cancel to continue”.

8. Press and release the “CANCEL” button as many times as necessary, so that, either the “Welcome to Photosmart Express” screen appears, or, the “Ink System Failure” screen appears. PLEASE DO NOT TRY TO PRINT AT THIS STAGE.

9. Using the Power Button, turn the unit OFF and unplug the power cable from back of the printer and wall outlet.

10. Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first and then into the back of the printer

11. Turn the unit on. The printer may display message “USE POWER BUTTON TO SHUTDOWN THE PRINTER” followed by “PRESS OK TO CONTINUE”. Press OK.

12. If the printer has already initialized, then go to the next step. If not, the printer will start the “ONE TIME INK INITIALIZATION PROCESS”. Allow this process to complete and do not interrupt. Once the initialization process is complete, the printer will print out a Diagnostic Page.

13. To verify printer functionality print a SELF TEST PAGE.

取消

评论