linux蓝牙鼠标自动断开,Manjaro Linux 连接蓝牙鼠标后重启电脑得重新连接 解决方案-Go语言中文社区...

从Ubuntu到CentOS 再到 Deepin Linux........折腾过很多发行版，前不久给自己的老电脑安装了win10+Manjaro双系统，manjaro是基于Arch的，不过相比arch人性化很多，不必一步一步构建系统，开机即用。但是也有一些小毛病，笔者就是因为Deepin linux bug太多换到Manjaro的。

笔者的鼠标是Logitech的蓝牙鼠标M337。再win10下完美使用，在Manjaro下连接上去后可以使用，但是就是每次关机后再开机就会失效，而且还连不上。必须得删除重新连接。很恶心的操作。翻看了网上的方法没有一个可以解决的，于是笔者自己瞎折腾，给解决了。

首先在软件管理包中安装Bluetooth的相关组件，如下都勾选上。

然后修改蓝牙配置文件：

sudo vim /etc/bluetooth/main.conf

修改FastConnectable = false ，取消#注释，改为FastConnectable = true

修改 AutoEnable=false，去掉前面的#注释，改为AutoEnable=true。

以下是我的配置详情，仅供参考：

[General]

# Default adapter name

# Defaults to 'BlueZ X.YZ'

#Name = BlueZ

# Default device class. Only the major and minor device class bits are

# considered. Defaults to '0x000000'.

#Class = 0x000100

# How long to stay in discoverable mode before going back to non-discoverable

# The value is in seconds. Default is 180, i.e. 3 minutes.

# 0 = disable timer, i.e. stay discoverable forever

#DiscoverableTimeout = 0

# How long to stay in pairable mode before going back to non-discoverable

# The value is in seconds. Default is 0.

# 0 = disable timer, i.e. stay pairable forever

#PairableTimeout = 0

# Use vendor id source (assigner), vendor, product and version information for

# DID profile support. The values are separated by ":" and assigner, VID, PID

# and version.

# Possible vendor id source values: bluetooth, usb (defaults to usb)

#DeviceID = bluetooth:1234:5678:abcd

# Do reverse service discovery for previously unknown devices that connect to

# us. This option is really only needed for qualification since the BITE tester

# doesn't like us doing reverse SDP for some test cases (though there could in

# theory be other useful purposes for this too). Defaults to 'true'.

#ReverseServiceDiscovery = true

# Enable name resolving after inquiry. Set it to 'false' if you don't need

# remote devices name and want shorter discovery cycle. Defaults to 'true'.

#NameResolving = true

# Enable runtime persistency of debug link keys. Default is false which

# makes debug link keys valid only for the duration of the connection

# that they were created for.

#DebugKeys = false

# Restricts all controllers to the specified transport. Default value

# is "dual", i.e. both BR/EDR and LE enabled (when supported by the HW).

# Possible values: "dual", "bredr", "le"

ControllerMode = dual

# Enables Multi Profile Specification support. This allows to specify if

# system supports only Multiple Profiles Single Device (MPSD) configuration

# or both Multiple Profiles Single Device (MPSD) and Multiple Profiles Multiple

# Devices (MPMD) configurations.

# Possible values: "off", "single", "multiple"

MultiProfile = on

# Permanently enables the Fast Connectable setting for adapters that

# support it. When enabled other devices can connect faster to us,

# however the tradeoff is increased power consumptions. This feature

# will fully work only on kernel version 4.1 and newer. Defaults to

# 'false'.

FastConnectable = true

# Default privacy setting.

# Enables use of private address.

# Possible values: "off", "device", "network"

# "network" option not supported currently

# Defaults to "off"

# Privacy = off

[GATT]

# GATT attribute cache.

# Possible values:

# always: Always cache attributes even for devices not paired, this is

# recommended as it is best for interoperability, with more consistent

# reconnection times and enables proper tracking of notifications for all

# devices.

# yes: Only cache attributes of paired devices.

# no: Never cache attributes

# Default: always

Cache = always

# Minimum required Encryption Key Size for accessing secured characteristics.

# Possible values: 0 and 7-16. 0 means don't care.

# Defaults to 0

# MinEncKeySize = 0

[Policy]

#

# The ReconnectUUIDs defines the set of remote services that should try

# to be reconnected to in case of a link loss (link supervision

# timeout). The policy plugin should contain a sane set of values by

# default, but this list can be overridden here. By setting the list to

# empty the reconnection feature gets disabled.

#ReconnectUUIDs=00001112-0000-1000-8000-00805f9b34fb,0000111f-0000-1000-8000-00805f9b34fb,0000110a-0000-1000-8000-00805f9b34fb

# ReconnectAttempts define the number of attempts to reconnect after a link

# lost. Setting the value to 0 disables reconnecting feature.

#ReconnectAttempts=7

# ReconnectIntervals define the set of intervals in seconds to use in between

# attempts.

# If the number of attempts defined in ReconnectAttempts is bigger than the

# set of intervals the last interval is repeated until the last attempt.

#ReconnectIntervals=1,2,4,8,16,32,64

# AutoEnable defines option to enable all controllers when they are found.

# This includes adapters present on start as well as adapters that are plugged

# in later on. Defaults to 'false'.

AutoEnable=true

关于双系统共用一个蓝牙鼠标key也是可以的，网上有教程，我就不写了。很简单，也很方便，不必来回切换鼠标的绑定。