三层交换机能传递路由吗?_三层交换机和路由器不同网段相互通信（单臂路由）...

重点：三层交换机与路由器配置(理解它的目的，主要是敲命令)

实验步骤一：二层交换机的配置：

在三个二层交换机上分别划出两VLAN，并将二层交换机上与三层交换或路由器上的接线设置为trunk接口

实验步骤二：三层交换机的配置：

1：首先在三层交换上划出两个VLAN，并进入VLAN为其配置IP，此IP将作为与他相连PC的网关。

2：将与二层交换机相连的线同样设置为trunk接线，并将三层交换与路由器连接的线设置为路由接口(no switchsport)

3：将路由器和下面的交换机进行单臂路由的配置

实验结果：拓扑图下各个PC均能相互通信

二层交换机的配置命令(SW0、1、2)：

SW 0:

Switch>

Switch>en

Switch#conf

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#vlan 2

Switch(config-vlan)#exit

Switch(config)#int f0/2

Switch(config-if)#switchport access vlan 2

Switch(config-if)#no shut

Switch(config-if)#int f0/3

Switch(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up

Switch(config-if)#exit

Switch(config)#

SW 1:

Switch>en

Switch#conf

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#int f0/2

Switch(config-if)#switchport access vlan 2

% Access VLAN does not exist. Creating vlan 2

Switch(config-if)#no shut

Switch(config-if)#exit

Switch(config)#int f0/3

Switch(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up

Switch(config-if)#

SW 2:

Switch>en

Switch#conf

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#int f0/2

Switch(config-if)#switchport access vlan 2

% Access VLAN does not exist. Creating vlan 2

Switch(config-if)#exit

Switch(config)#int f0/3

Switch(config-if)#switchport mode trunk

Switch(config-if)#

三层交换的配置命令：

Switch>en

Switch#conf

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#int f0/1

Switch(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down

Switch(config-if)#exit

Switch(config)#int f0/2

Switch(config-if)#switchport mode trunk

Switch(config-if)#exit

Switch(config)#vlan 2

Switch(config-vlan)#exit

Switch(config)#int vlan 1

Switch(config-if)#no shut

%LINK-5-CHANGED: Interface Vlan1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up

Switch(config-if)#ip address 192.168.1.168 255.255.255.0

Switch(config-if)#exit

Switch(config)#int vlan 2

%LINK-5-CHANGED: Interface Vlan2, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to upSwitch(config-if)#ip add

Switch(config-if)#ip address 192.168.2.168 255.255.255.0

Switch(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/3, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up

Switch(config-if)#exit

Switch(config)#int f0/3

Switch(config-if)#no switchport

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to upSwitch(config-if)#

Switch(config-if)#ip address 192.168.10.1 255.255.255.0

Switch(config-if)#no shut

Switch(config-if)#exit

Switch(config)#ip routing

Switch(config-if)#exit

Switch(config)#ip route 0.0.0.0 0.0.0.0 192.168.10.2

Switch(config)#

路由器的配置：

Router>en

Router#conf

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int f0/0

Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#int f0/1

Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#exit

Router(config)#int f0/0

Router(config-if)#no shut

Router(config-if)#exit

Router(config)#int f0/0.1

Router(config-subif)#encapsulation dot1Q 1

Router(config-subif)#ip address 192.168.3.168 255.255.255.0

Router(config-subif)#exit

Router(config)#int f0/0.2

Router(config-subif)#encapsulation dot1Q 2

Router(config-subif)#ip add

Router(config-subif)#ip address 192.168.4.168 255.255.255.0

Router(config-subif)#exit

Router(config)#ip route 0.0.0.0 0.0.0.0 192.168.10.1

Router(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

Router#conf

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int f0/1

pan>Router(config-subif)#ip address 192.168.3.168 255.255.255.0

Router(config-subif)#exit

Router(config)#int f0/0.2

Router(config-subif)#encapsulation dot1Q 2

Router(config-subif)#ip add

Router(config-subif)#ip address 192.168.4.168 255.255.255.0

Router(config-subif)#exit

Router(config)#ip route 0.0.0.0 0.0.0.0 192.168.10.1

Router(config)#exit

%SYS-5-CONFIG_I: Configured from console by console

Router#conf

Configuring from terminal, memory, or network [terminal]?

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int f0/1

Router(config-if)#ip add

Router(config-if)#ip address 192.168.10.2 255.255.255.0

Router(config-if)#

Router(config-if)#ip add

Router(config-if)#ip address 192.168.10.2 255.255.255.0

Router(config-if)#