linux系统时间有两个,一个是硬件时间,即BIOS时间,就是我们进行CMOS设置时看到的时间,另一个是系统时间,是linux系统Kernel时间。当Linux启动时,系统Kernel会去读取硬件时钟的设置,然后系统时钟就会独立于硬件运作。有时我们会发现系统时钟和硬件时钟不一致,因此需要执行时间同步。
date -R 查看当前时区
一、date 查看/设置系统时间
1、将日期设置为2020年02月15日
[root@linux-node ~]# date -s 15/02/20
2、将时间设置为14点20分50秒
[root@linux-node ~]# date -s 14:20:50
3、将时间设置为2020年02月15日14点16分30秒(MMDDhhmmYYYY.ss)
[root@linux-node ~]# date 1502141620.30
[root@linux-node ~]# date -s "2020-02-15 14:16:30"
二、hwclock/clock 查看/设置硬件时间
1、查看系统硬件时钟
[root@linux-node ~]# hwclock --show 或者
[root@linux-node ~]# clock --show
2、设置硬件时间
[root@linux-node ~]# hwclock --set --date="15/02/20 14:55"
(月/日/年时:分:秒) 或者
[root@linux-node ~]# clock --set --date="15/02/20 14:55"
(月/日/年时:分:秒)
[root@linux-node ~]# hwclock -w 保存修改结果
三、同步系统及硬件时钟
[root@linux-node ~]# hwclock --hctosys 或者
[root@linux-node ~]# clock --hctosys
备注:hc代表硬件时间,sys代表系统时间,以硬件时间为基准,系统时间找硬件时间同步
[root@linux-node ~]# hwclock --systohc或者
[root@linux-node ~]# clock --systohc
备注:以系统时间为基准,硬件时间找系统时间同步
方法二
时区设置用tzselect
命令来实现。但是通过tzselect命令设置TZ这个环境变量来选择的时区,需要将变量添加到.profile文件中。
一、tzselect命令执行
执行tzselect命令 --> 选择Asia --> 选择China --> 选择east China
- Beijing, Guangdong, Shanghai, etc-->然后输入1。
执行完tzselect命令选择时区后,时区并没有更改,只是在命令最后提示你可以执行 TZ=’Asia/Shanghai’;
export TZ 并将这行命令添加到.profile中,然后退出并重新登录。
二、修改配置文件来修改时区
[root@linux-node ~]# echo "ZONE=Asia/Shanghai" >>
/etc/sysconfig/clock
[root@linux-node ~]# rm -f /etc/localtime
#链接到上海时区文件
[root@linux-node ~]# ln -sf /usr/share/zoneinfo/Asia/Shanghai
/etc/localtime
执行完上述过程后,重启机器,即可看到时区已经更改。
备注:
在centos7中设置时区的命令可以通过 timedatectl 命令来实现
[root@linux-node ~]# timedatectl set-timezone
Asia/Shanghai
https://www.cnblogs.com/xiaojianblogs/p/8949932.html
ntp客户端配置
1.检查系统是否安装了NTP包(linux系统一般自带NTP4.2),没有安装我们直接使用yum命令在线安装: yum
install ntp (yum install ntp ntpdate -y)
[root@linux-node ~]# rpm -qa | grep ntp
2.启动NTP时间服务器:
[root@linux-node ~]# systemctl status ntpd
[root@linux-node ~]# systemctl start ntpd (service ntpd start
)
[root@linux-node ~]# systemctl enable ntpd
3.设置NTP开机自动启动:chkconfig ntpd on
4.查看NTP是否正常运行:netstat -t l unp | grep ntp
修改/etc/ntp.conf文件,内容如下
#注释掉其他上游时间服务器
#配置上游时间服务器为本地的ntpd Server服务器
server 192.168.0.163
#配置允许上游时间服务器主动修改本机的时间
restrict 192.168.0.163 nomodify notrap noquery
5。与ntpd Server同步一下
[root@linux-node ~]# ntpdate -u 192.168.0.163
查看状态
[root@linux-node ~]# ntpq -p
ntp服务,默认只会同步系统时间。如果想要让ntp同时同步硬件时间,可以设置/etc/sysconfig/ntpd文件,在/etc/sysconfig/ntpd文件中,添加
SYNC_HWCLOCK=yes 这样,就可以让硬件时间与系统时间一起同步。
https://blog.csdn.net/hellboy0621/article/details/81903091