linux 双网卡主备,Linux双网卡负载均衡(转)

Linux双网卡负载均衡

[root@localhost ~]# uname -a

Linux localhost.localdomain 2.6.9-55.EL #1 Fri Apr 20 16:35:59 EDT 2007 i686 i686 i386 GNU/Linux

查看linux是否支持bonding，如下信息表示已支持

[root@localhost ~]# modinfo bonding

filename:       /lib/modules/2.6.9-55.EL/kernel/drivers/net/bonding/bonding.ko

parm:           max_bonds:Max number of bonded devices

parm:           miimon:Link check interval in milliseconds

parm:           updelay:Delay before considering link up, in milliseconds

parm:           downdelay:Delay before considering link down, in milliseconds

parm:           use_carrier:Use netif_carrier_ok (vs MII ioctls) in miimon; 0 for off, 1 for on (default)

parm:           mode:Mode of operation : 0 for round robin, 1 for active-backup, 2 for xor

parm:           primary:Primary network device to use

parm:           lacp_rate:LACPDU tx rate to request from 802.3ad partner (slow/fast)

parm:           xmit_hash_policy:XOR hashing method : 0 for layer 2 (default), 1 for layer 3+4

parm:           arp_interval:arp interval in milliseconds

parm:           arp_ip_target:arp targets in n.n.n.n form

license:        GPL

version:        2.6.3-rh BEB2ABDD4B642BA33CF1587

description:    Ethernet Channel Bonding Driver, v2.6.3-rh

author:         Thomas Davis,and many others

vermagic:       2.6.9-55.EL 686 REGPARM 4KSTACKS gcc-3.4

depends:

1.编辑虚拟网络接口配置文件,指定网卡IP

[root@localhost ~]# cd /etc/sysconfig/network-scripts/

[root@localhost ~]# cp ifcfg-eth0 ifcfg-bond0

[root@localhost ~]# vi ifcfg-bond0

DEVICE=bond0

BOOTPROTO=none

ONBOOT=yes

TYPE=Ethernet

NETMASK=255.255.255.0

IPADDR=192.168.1.30

USERCTL=no

IPV6INIT=no

PEERDNS=yes

[root@localhost network-scripts]# less ifcfg-eth0

DEVICE=eth0

ONBOOT=yes

BOOTPROTO=none

MASTER=bond0

SLAVE=yes

[root@localhost network-scripts]# less ifcfg-eth1

DEVICE=eth1

BOOTPROTO=none

ONBOOT=yes

MASTER=bond0

SLAVE=yes

2.编辑/etc/moprobe.conf文件，加入如下一行内容，以使系统在启动时加载bonding模块，对外虚拟网络接口设备为 bond0

[root@localhost ~]# vi /etc/moprobe.conf

加入下列行

alias bond0 bonding

options bond0 miimon=100 mode=1

说明：miimon是用来进行链路监测的。 比如:miimon=100，那么系统每100ms监测一次链路连接状态，如果有一条线路不通就转入另一条线路；mode的值表示工作模式，他共有0,1,2,3四种模式，常用的为0,1两种。

mode=0表示load balancing (round-robin)为负载均衡方式，两块网卡都工作。

mode=1表示fault-tolerance (active-backup)提供冗余功能，工作方式是主备的工作方式,也就是说默认情况下只有一块网卡工作,另一块做。

bonding只能提供链路监测，即从主机到交换机的链路是否接通。如果只是交换机对外的链路down掉了，而交换机本身并没有故障，那么bonding会认为链路没有问题而继续使用。

3.编辑/etc/rc.d/rc.local

[root@localhost ~]# vi /etc/rc.d/rc.local

加入

ifenslave bond0 eth0 eth1

重启后我们用ifconfig查看网卡信息,可以看到多出一个bond0网卡

bond0     Link encap:Ethernet  HWaddr 00:1D:0F:14:7D:1A

inet addr:192.168.1.30  Bcast:192.168.1.255  Mask:255.255.255.0

inet6 addr: fe80::21d:fff:fe14:7d1a/64 Scope:Link

UP BROADCAST RUNNING MASTER MULTICAST  MTU:1500  Metric:1

RX packets:4537 errors:0 dropped:0 overruns:0 frame.:0

TX packets:482 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:472954 (461.8 KiB)  TX bytes:51396 (50.1 KiB)

eth0      Link encap:Ethernet  HWaddr 00:1D:0F:14:7D:1A

inet6 addr: fe80::21d:fff:fe14:7d1a/64 Scope:Link

UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1

RX packets:2186 errors:0 dropped:0 overruns:0 frame.:0

TX packets:220 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000

RX bytes:227915 (222.5 KiB)  TX bytes:23294 (22.7 KiB)

Interrupt:185 Base address:0xc000

eth1      Link encap:Ethernet  HWaddr 00:1D:0F:14:7D:1A

inet6 addr: fe80::21d:fff:fe14:7d1a/64 Scope:Link

UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1

RX packets:2353 errors:0 dropped:0 overruns:0 frame.:0

TX packets:270 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000

RX bytes:245159 (239.4 KiB)  TX bytes:29194 (28.5 KiB)

Interrupt:209 Base address:0xc400

此时网卡已绑定成功！！