西南科技大学计算机网络 实验题目--带答案
(8页)
本资源提供全文预览,点击全文预览即可全文预览,如果喜欢文档就下载吧,查找使用更方便哦!
11.90 积分
1、配置特权模式执行口令:Router1/Switch (config)# enable secret cisco 2、配置路由器/交换机控制台口令 Router1/Switch(config)# line console 0 Router1/Switch (config-line)# password class Router1/Switch (config-line)# login3、配置路由器/交换机虚拟线路口令Router1/Switch1(config-line)# line vty 0 4/0 15 Router1/Switch1(config-line)# password class Router1/Switch1(config-line)# login4、配置交换机的第 3 层地址。(实验2,任务3,步骤4)在内部虚拟接口 VLAN 99 上将交换机的 IP 地址设置为 172.17.99.11,子网掩码为 255.255.255.0。首先必须在交换机上创建 VLAN,然后才能分配地址。S1(config)#vlan 99S1(config-vlan)#exitS1(config)#interface vlan99S1(config-if)#ip address 172.17.99.11 255.255.255.0S1(config-if)#no shutdownS1(config-if)#exit5、为交换机 S1 VLAN 分配端口。(实验2,任务3,步骤5)将 Fastethernet 0/1、0/8 和 0/18 端口分配给 VLAN 99。S1(config)#interface fa0/1S1(config-if)#switchport access vlan 99S1(config-if)#exit6、修改交换机名称为S1,配置交换机网关为172.17.99.1(实验2,任务3,步骤 6),禁用 DNS 查找。S1(config)#hostname S1S1(config)#ip default-gateway 172.17.99.1S1(config)#no ip domain-lookup7、配置 FastEthernet 0/18 端口为全双工,速率为100。(实验2,任务3,步骤 10)S1(config)#interface fa 0/18S1(config-if)#speed 100 S1(config-if)#duplex full8、配置交换机端口 FastEthernet 0/18 仅接受两台设备,动态学习这些设备的 MAC 地址,并在发生安全违规事件时关闭端口。(实验2,任务5,步骤4、5)S1# configure terminalS1(config)#interface fa0/18S1(config-if)#switchport mode accessS1(config-if)#switchport port-security maximum 2S1(config-if)#switchport port-security mac-address stickyS1(config-if)#switchport port-security violation shutdown9、 配置 VTP工作模式/域名/口令。(实验3,-省略部分-6)步骤 1 在 R1 上使用地址 10.1.1.1 255.255.255.255 配置 Loopback0 接口步骤 2 在 R2 上使用地址 10.2.2.2 255.255.255.255 配置 Loopback0 接口步骤 3 在 R3 上使用地址 10.3.3.3 255.255.255.255 配置 Loopback0 接口R1(config)#interface loopback 0R1(config-if)#ip address 10.1.1.1 255.255.255.255R2(config)#interface loopback 0R2(config-if)#ip address 10.2.2.2 255.255.255.255R3(config)#interface loopback 0R3(config-if)#ip address 10.3.3.3 255.255.255.25517、在路由器 R1 上配置 OSPF步骤 1:在路由器 R1 上,在全局配置配配下使用 router ospf 命令启用 OSPF。对于 process-ID 参数,输入进程 ID 1。R1(config)#router ospf 1步骤 2:配置 LAN 的 network 当句。R1(config-router)#network 172.16.1.16 0.0.0.15 area 0步骤 3:配置路由器,使其通告 Serial0/0/0 接口所连接的网络 192.168.10.0/30。R1(config-router)# network 192.168.10.0 0.0.0.3 area 0步骤 4:配置路由器,使其通告 Serial0/0/1 接口所连接的网络 192.168.10.4/30。R1(config-router)# network 192.168.10.4 0.0.0.3 area 018、Cisco 路由器上的默认串行封装是 HDLC。将串行接口的封装由 HDLC 改为 PPP。步骤 1. 在 R1 和 R2 间的串行链路上配置 PPP PAP 身份验证。R1(config)#username R1 password ciscoR1(config)#int s0/0/0R1(config-if)#ppp authentication papR2(config)#username R2 password ciscoR2(config)#interface Serial0/0/0R2(config-if)#ppp authentication papR2(config-if)#ppp pap sent-username R1 password cisco步骤 2. 在 R2 和 R3 间的串行链路上配置 PPP CHAP 身份验证。R2(config)#username R3 password ciscoR2(config)#int s0/0/1R2(config-if)#ppp authentication chapR3(config)#username R2 password ciscoR3(config)#int s0/0/1R3(config-if)#ppp authentication chap
关 键 词:
科技大学 题目 实验 西南 答案 计算机网络
天天文库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
关于本文
本文标题:西南科技大学计算机网络 实验题目--带答案
链接地址:
https://www.wenku365.com/p-47521874.html