micropython ota_MicroPython （一）点亮我的Led

工具 ：

putty

F429Discovery 开发板

Notepad++

注意：不知道为什么 其他的终端工具有问题，推荐 putty 基本没有发现问题

putty 实时调试

使用putty 打开USB 虚拟串口，我们打开可以使用help()方法寻求帮助

输入help()如下所示

help()

Welcome to MicroPython!

For online help please visit http://micropython.org/help/.

Quick overview of commands for the board:

pyb.info() -- print some general information

pyb.delay(n) -- wait for n milliseconds

pyb.millis() -- get number of milliseconds since hard reset

pyb.Switch() -- create a switch object

Switch methods: (), callback(f)

pyb.LED(n) -- create an LED object for LED n (n=1,2,3,4)

LED methods: on(), off(), toggle(), intensity()

pyb.Pin(pin) -- get a pin, eg pyb.Pin('X1')

pyb.Pin(pin, m, [p]) -- get a pin and configure it for IO mode m, pull mode p

Pin methods: init(..), value([v]), high(), low()

pyb.ExtInt(pin, m, p, callback) -- create an external interrupt object

pyb.ADC(pin) -- make an analog object from a pin

ADC methods: read(), read_timed(buf, freq)

pyb.DAC(port) -- make a DAC object

DAC methods: triangle(freq), write(n), write_timed(buf, freq)

pyb.RTC() -- make an RTC object; methods: datetime([val])

pyb.rng() -- get a 30-bit hardware random number

pyb.Servo(n) -- create Servo object for servo n (n=1,2,3,4)

Servo methods: calibration(..), angle([x, [t]]), speed([x, [t]])

pyb.Accel() -- create an Accelerometer object

Accelerometer methods: x(), y(), z(), tilt(), filtered_xyz()

Pins are numbered X1-X12, X17-X22, Y1-Y12, or by their MCU name

Pin IO modes are: pyb.Pin.IN, pyb.Pin.OUT_PP, pyb.Pin.OUT_OD

Pin pull modes are: pyb.Pin.PULL_NONE, pyb.Pin.PULL_UP, pyb.Pin.PULL_DOWN

Additional serial bus objects: pyb.I2C(n), pyb.SPI(n), pyb.UART(n)

Control commands:

CTRL-A -- on a blank line, enter raw REPL mode

CTRL-B -- on a blank line, enter normal REPL mode

CTRL-C -- interrupt a running program

CTRL-D -- on a blank line, do a soft reset of the board

CTRL-E -- on a blank line, enter paste mode

For further help on a specific object, type help(obj)

For a list of available modules, type help('modules')

上面就是所有的Micro Python 帮助文档。

输入下面的指令打开一个Led。

>>> import pyb

>>> led = pyb.LED(1)

>>> led.on()

>>> led.off()

MicroPython 脱机运行

脱机运行指离开电脑独立运行，在插入USB的时候，电脑多了一个磁盘（不是Stlink V2.1），我们打开这个磁盘，里面有一个“main.py”文件。

打开这个文件，可以在里面输入如下代码

import pyb

while true：

pyb.LED(1).on()

pyb.delay(500)

pyb.LED(1).off()

pyb.delay(500)

保存“main.py”文件，完成复位即可。