linux几种链路聚合模式,使用nmcli配置主备模式链路聚合

主备模式的链路聚合将其中一个接口置于备份状态，并且仅当活动接口断开链接时才会使其处于活动状态。

现在让我们在CentOS7中配置网卡绑定，运行ip link命令查看可以使用的网卡

[root@localhost ~]# ip link

1: lo: mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000

link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00

2: enp0s3: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000

link/ether 08:00:27:7b:d3:32 brd ff:ff:ff:ff:ff:ff

3: enp0s8: mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000

link/ether 08:00:27:81:d3:be brd ff:ff:ff:ff:ff:ff

在这里使用enp0s3和enp0s8两个网卡配置 主备模式的链路聚合。

创建Team接口

[root@localhost ~]# nmcli connection add type team con-name team0 ifname team0 config '{"runner":{"name":"activebackup"}}'

Connection 'team0' (4df78635-b9fc-4539-ab02-27db11c656fe) successfully added.

运行nmcli con show查看team0的配置

[root@localhost ~]# nmcli con show

NAME UUID TYPE DEVICE

team0 4df78635-b9fc-4539-ab02-27db11c656fe team team0

enp0s3 5005942f-a7fd-4e55-b8e7-77928d8da72d ethernet enp0s3

Wired connection 1 45dee64a-53b3-3e2a-b2d4-e377f3e668a2 ethernet enp0s8

添加Slave接口

在这里使用enp0s3和enp0s8两个网卡作为team0的slave接口：

[root@localhost ~]# nmcli connection add type team-slave con-name team0-port1 ifname enp0s3 master team0

Connection 'team0-port1' (15183c4a-2053-4b53-ad58-de5a07ae3ae9) successfully added.

[root@localhost ~]# nmcli connection add type team-slave con-name team0-port2 ifname enp0s8 master team0

Connection 'team0-port2' (a34e20b0-3422-46e5-a947-bb2eaa6c0622) successfully added.

查看端口配置信息：

[root@localhost ~]# nmcli connection show

NAME UUID TYPE DEVICE

team0 4df78635-b9fc-4539-ab02-27db11c656fe team team0

enp0s3 5005942f-a7fd-4e55-b8e7-77928d8da72d ethernet enp0s3

Wired connection 1 45dee64a-53b3-3e2a-b2d4-e377f3e668a2 ethernet enp0s8

team0-port1 15183c4a-2053-4b53-ad58-de5a07ae3ae9 ethernet --

team0-port2 a34e20b0-3422-46e5-a947-bb2eaa6c0622 ethernet --

分配IP地址

给team0分配一个静态的IP地址并启动team0配置：

[root@localhost ~]# nmcli connection modify team0 ipv4.method manual ipv4.addresses 192.168.0.200/24 ipv4.gateway 192.168.0.1 ipv4.dns 202.102.128.68

[root@localhost ~]# nmcli connection up team0

Connection successfully activated (master waiting for slaves) (D-Bus active path: /org/freedesktop/NetworkManager/ActiveConnection/4)

查看连接配置信息，发现team0-port1没有绑定在enp0s3这个网卡接口上

[root@localhost ~]# nmcli connection

这是以内ifcfg-team0-port1配置文件和ifcfg-enp0s3两个配置文件都设置为开机启动了

所以我们需要关闭enp0s3的开机启动，在这里我们把enp0s3和Wired connection 1这两个配置都关掉开机启动

[root@localhost ~]# nmcli connection modify enp0s3 autoconnect no

[root@localhost ~]# nmcli connection modify Wired\ connection\ 1 autoconnect no

然后重启一下网络服务，查看链接配置：

[root@localhost ~]# systemctl restart network

[root@localhost ~]# nmcli connection

[root@localhost ~]# ip ad

可以看到team0-port1和team0-port2都绑定在对应的网卡上面了，team0的ip地址显示的是手动设置的192.168.0.200

验证

查看team0的状态：

[root@localhost ~]# teamdctl team0 state

setup:

runner: activebackup

ports:

enp0s3

link watches:

link summary: up

instance[link_watch_0]:

name: ethtool

link: up

down count: 0

enp0s8

link watches:

link summary: up

instance[link_watch_0]:

name: ethtool

link: up

down count: 0

runner:

active port: enp0s8

现在活动的端口是enp0s8，我们断开这个端口，看一下主备模式配置是否工作：

[root@localhost ~]# nmcli device disconnect enp0s8

Device 'enp0s8' successfully disconnected.

[root@localhost ~]# teamdctl team0 state

setup:

runner: activebackup

ports:

enp0s3

link watches:

link summary: up

instance[link_watch_0]:

name: ethtool

link: up

down count: 0

runner:

active port: enp0s3

看到活动接口切换到enp0s3上面了。

总结

主备模式的链路聚合将其中一个接口置于备份状态，并且仅当活动接口断开链接时才会使其处于活动状态。