红帽子linux编译命令,技术|Linux 有问必答: 如何在红帽系linux中编译Ixgbe驱动

提问：我想要安装最新版的ixgbe 10G网卡驱动。在CentOS, Fedora 或 RHEL中，我应该如何编译ixgbe驱动？

想要在linux使用Intel的PCI Express 10G网卡(例如，82598，82599，x540)，需要安装Ixgbe驱动。如今的Linux发行版都会预安装ixgbe的可加载模块，但是预安装的ixgbe驱动不是完整功能版。如果想要开启和定制所有10G网卡的功能(如，RSS、多队列、虚拟化功能、硬件 offload 等)，需要从源码编译安装。

本文基于红帽系平台(如，CentOS，RHEL或Fedora)。Debian系平台，请看这篇文章。

第一步: 安装依赖

首先，安装必要的开发环境和安装匹配的内核头文件

$ sudo yum install gcc make

$ sudo yum install kernel-devel

第二步: 编译Ixgbe

从官方页面下载最新Ixgbe源码

$ wget http://downloads.sourceforge.net/project/e1000/ixgbe%20stable/3.23.2/ixgbe-3.23.2.tar.gz

请检查支持的内核版本。例如，Ixgbe3.23.2版本支持Linux内核版本2.6.18到3.18.1。

提取压缩包并编译：

$ tar -xvf ixgbe-3.23.2.tar.gz

$ cd ixgbe-3.23.2/src

$ make

如果成功，可以在当前目录找到编译完成的驱动(ixgbe.ko)。

可以运行这个命令来查看编译信息：

$ modinfo ./ixgbe.ko

将会输出一个Ixgbe驱动的可用参数列表

第三步: 加载 Ixgbe 驱动

这步准备加载已经编译好的驱动。

如果系统已经加载了Ixgbe驱动，首先需要卸载掉老版本。否则，新版本不能加载。

$ sudo rmmod ixgbe.ko

然后插入编译完成的驱动到内核中：

$ sudo insmod ./ixgbe.ko

同时，你可以设置启动参数

$ sudo insmod ./ixgbe.ko FdirPballoc=3 RSS=16

验证驱动是否加载成功，使用dmesg命令，查看其输出

$ dmesg

Intel(R) 10 Gigabit PCI Express Network Driver - version 3.23.2

Copyright (c) 1999-2014 Intel Corporation.

ixgbe 0000:21:00.0: PCI INT A -> GSI 64 (level, low) -> IRQ 64

ixgbe 0000:21:00.0: setting latency timer to 64

ixgbe: Receive-Side Scaling (RSS) set to 16

ixgbe: Flow Director packet buffer allocation set to 3

ixgbe: 0000:21:00.0: ixgbe_check_options: Flow Director will be allocated 256kB of packet buffer

ixgbe: 0000:21:00.0: ixgbe_check_options: FCoE Offload feature enabled

ixgbe 0000:21:00.0: irq 87 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 88 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 89 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 90 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 91 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 92 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 93 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 94 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 95 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 96 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 97 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 98 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 99 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 100 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 101 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 102 for MSI/MSI-X

ixgbe 0000:21:00.0: irq 103 for MSI/MSI-X

ixgbe 0000:21:00.0: eth3: DCA registration failed: -1

ixgbe 0000:21:00.0: PCI Express bandwidth of 32GT/s available

ixgbe 0000:21:00.0: (Speed:5.0GT/s, Width: x8, Encoding Loss:20%)

ixgbe 0000:21:00.0: eth3: MAC: 2, PHY: 9, SFP+: 3, PBA No: E68793-006

ixgbe 0000:21:00.0: 90:e2:ba:5b:e9:1c

ixgbe 0000:21:00.0: eth3: Enabled Features: RxQ: 16 TxQ: 16 FdirHash RSC

ixgbe 0000:21:00.0: eth3: Intel(R) 10 Gigabit Network Connection

ixgbe 0000:21:00.1: PCI INT B -> GSI 68 (level, low) -> IRQ 68

ixgbe 0000:21:00.1: setting latency timer to 64

ixgbe: 0000:21:00.1: ixgbe_check_options: FCoE Offload feature enabled

ixgbe 0000:21:00.0: registered PHC device on eth3

ixgbe 0000:21:00.1: irq 104 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 105 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 106 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 107 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 108 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 109 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 110 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 111 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 112 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 113 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 114 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 115 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 116 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 117 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 118 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 119 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 120 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 121 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 122 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 123 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 124 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 125 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 126 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 127 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 128 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 129 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 130 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 131 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 132 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 133 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 134 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 135 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 136 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 137 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 138 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 139 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 140 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 141 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 142 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 143 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 144 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 145 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 146 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 147 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 148 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 149 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 150 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 151 for MSI/MSI-X

ixgbe 0000:21:00.1: irq 152 for MSI/MSI-X

ADDRCONF(NETDEV_UP): eth3: link is not ready

8021q: adding VLAN 0 to HW filter on device eth3

ixgbe 0000:21:00.1: eth4: DCA registration failed: -1

ixgbe 0000:21:00.1: PCI Express bandwidth of 32GT/s available

ixgbe 0000:21:00.1: (Speed:5.0GT/s, Width: x8, Encoding Loss:20%)

ixgbe 0000:21:00.1: eth4: MAC: 2, PHY: 9, SFP+: 4, PBA No: E68793-006

ixgbe 0000:21:00.1: 90:e2:ba:5b:e9:1e

ixgbe 0000:21:00.1: eth4: Enabled Features: RxQ: 48 TxQ: 48 FdirHash RSC

ixgbe 0000:21:00.1: eth4: Intel(R) 10 Gigabit Network Connection

ixgbe 0000:21:00.0: eth3: detected SFP+: 3

ixgbe 0000:21:00.1: registered PHC device on eth4

ADDRCONF(NETDEV_UP): eth4: link is not ready

8021q: adding VLAN 0 to HW filter on device eth4

ixgbe 0000:21:00.1: eth4: detected SFP+: 4

ixgbe 0000:21:00.0: eth3: NIC Link is Up 10 Gbps, Flow Control: RX/TX

ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready

ixgbe 0000:21:00.1: eth4: NIC Link is Up 10 Gbps, Flow Control: RX/TX

ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready

eth3: no IPv6 routers present

eth4: no IPv6 routers present

第四步: 安装Ixgbe驱动

当确认驱动已经加载后，就可以安装驱动到系统中了

$ sudo make install

ixgbe.ko将会安装在下列目录

/lib/modules//kernel/drivers/net/ixgbe

此时，编译好的驱动将在启动时自动加载，也可以通过运行命令加载它：

$ sudo modprobe ixgbe

本文由 LCTT 原创翻译，Linux中国 荣誉推出