龙芯S-2K2000板卡测试记录，loongnix系统已知问题及Buildroot跑DPDK

Jim w

已于 2023-10-25 14:45:22 修改

阅读量996

点赞数 1

文章标签： stm32 嵌入式硬件单片机

于 2023-10-18 20:06:54 首次发布

本文链接：https://blog.csdn.net/weixin_42414349/article/details/133912339

版权

S-2K2000板卡已知问题

安装系统时PMON需要使用acpi传参
pmon下USB键盘不支持热插拔
pmon下插入部分USB键盘进pmon特别慢，兼容性问题，后续统一解决
不支持emmc，等待更新pmon

S-2K2000板卡手动引导USB命令

load  (usb0,0)/boot/vmlinuz.
initrd  (usb0,0)/boot/initrd.gz
g console=ttyS0,115200

PMON编译方法

安装ubuntu20.04系统
解压龙芯交叉编译工具到/opt目录

tar xvf loongarch64-linux-gnu-2021-06-19-vector.tar.gz -C /opt/

修改ACPI传参。文件路径：PMON下的Targets/ls2k2000/conf/ls.2k2000；配置文件：ls_anpk.2k2000，可以覆盖。修改内容为ACPI的三个选项，取消注释

#
#  Define target endian
#
makeoptions     ENDIAN=EL               # Little endian version.

option          SMBIOS_SUPPORT
option          ACPI_SUPPORT   //取消注释
select          acpi_support    //取消注释
option          LS_STR     //取消注释

编译pmon，执行cmd.sh

cd zloader.ls2k2000
make cfg all tgt=rom ARCH=loongarch CROSS_COMPILE=/opt/loongarch64-linux-gnu-2021-06-19-vector/bin/loongarch64-linux-gnu- DEBUG=-g
make dtb ARCH=loongarch CROSS_COMPILE=/opt/loongarch64-linux-gnu-2021-06-19-vector/bin/loongarch64-linux-gnu-

S-2K2000安装系统的步骤

更新GPU_FUSE pmon
执行fuse_write升级GPU固件，并check
更新ACPI传参pmon
安装系统（2个版本均可）
替换内核
修改boot.cfg
更新正式pmon

龙芯2K2000 GPU固件升级

烧录gpufuse固件（pmon_2k2000_gpufuse_nuc.bin）
pmon下执行fuse_write–》重启板卡–》pmon下执行fuse_check
重启确认显示正常
烧录回旧pmon（目前nuc固件不支持USB，需要通过tftp烧录）

TFTP烧录pmon的方法

启动到pmon命令行下，开机时按c进入pmon
查看设备列表devls

PMON> devls
Device name  Type
syn0         IFNET
syn1         IFNET
syn2         IFNET
wd0          DISK
ngbe0        IFNET
ngbe1        IFNET
ngbe2        IFNET
ngbe3        IFNET
ngbe4        IFNET
ngbe5        IFNET
ngbe6        IFNET
ngbe7        IFNET
ngbe8        IFNET
ngbe9        IFNET
PMON>

配置ip
ifconfig syn0 10.50.122.1
测试网络
ping 10.50.122.10
准备TFTP服务器，推荐用Windows tftd64软件
TFTP烧录pmon
fload tftp://10.10.10.10/gzrom-gpu.bin

支持的操作系统（已实测安装）

龙芯嵌入式系统 Loongnix-Embedded-20.1.rc3-loongarch64-DVD-1。
已知问题：没有网络源。
龙芯loongnix系统 Loongnix-20.5.livecd.loongarch64.iso。
已知问题：找不到I2C设备，需要替换内核。不支持DTS传参。

龙芯系统替换内核的方法

loongnix系统更换为anntec内核后需要改为DTS传参，注销ACPI选项后重新编译PMON，并更新到板卡。

挂载分区2
mount /dev/sda2 /mnt
修改boot.cfg 增加一个内核选项
vim /mnt/boot.cfg
拷贝已经适配过的anntec内核vminuz文件到分区2
cp vminuz /mnt/
卸载分区2
umount /mnt

修改dmi显示的modle name方法：

默认显示的model_name是 Loongson-2K2000-EVB-V1.0

root@test-pc:~# lscpu
Architecture:          loongarch64
  Byte Order:          Little Endian
CPU(s):                2
  On-line CPU(s) list: 0,1
BIOS Vendor ID:        Loongson-2K2000-EVB-V1.0
Model name:            Loongson-2K2000-EVB-V1.0
  BIOS Model name:     Loongson-2K2000-EVB-V1.0  CPU @ 1.2GHz
  BIOS CPU family:     1
  CPU family:          Loongson-64bit
  Thread(s) per core:  1
  Core(s) per socket:  2
  Socket(s):           1
  BogoMIPS:            2400.00
  Flags:               cpucfg lam ual fpu lsx crc32 lbt_x86 lbt_arm lbt_mips
Caches (sum of all):   
  L1d:                 128 KiB (2 instances)
  L1i:                 128 KiB (2 instances)
  L2:                  2 MiB (1 instance)
NUMA:                  
  NUMA node(s):        1
  NUMA node0 CPU(s):   0,1

pmon目录下执行grep -rn "board_name"找到对应的文件路径/pmon/common/smbios/smbios.c
修改对应的值后重新编译

#elif defined(LOONGSON_2K2000)
        sprintf(board_name, "S-%s-V1.0", "2K2000");

更新pmon后测试，已经修改了原先的

root@test-pc:~# dmidecode -t2
# dmidecode 3.2
Getting SMBIOS data from sysfs.
SMBIOS 2.6 present.

Handle 0x0002, DMI type 2, 17 bytes
Base Board Information
	Manufacturer: Anntec.cn S-2K2000-V1.0
	Product Name: 1.0
	Version: <BAD INDEX>
	Serial Number: Not Specified
	Asset Tag: Not Specified
	Features:
		Board is a hosting board
		Board is replaceable
	Location In Chassis: Not Specified
	Chassis Handle: 0x0000
	Type: Motherboard
	Contained Object Handles: 0

DPDK的测试方法前面文章已有讲述，记录一些注意事项

NAS上传的dpdk-l2fwd程序版本为21.11 ，启动命令需要加一个参数-P
./l2fwd -l 1 --proc-type auto --socket-mem 1024 --file-prefix lwd0 -- -q 2 -p 0x3 -T 5 --no-mac-updating -P ./l2fwd -l 1 --proc-type auto --socket-mem 1024 --file-prefix lwd0 -- -q 4 -p 0xf -T 5 --no-mac-updating -P ./l2fwd -l 1 -- -q2 -p3 -T0 --no-mac-updating -r 128 -t 256 -P
目前测试丢包较多，修改boot.cfg添加了isolcpus=1，使用core1来跑，稍有改善。龙芯认为是系统干扰严重，推荐用buildroot测试，等待更新。

i2c操作bypass命令

关闭bypass
i2cset -f -y 0 0x2f 0x21 0x00
保存设置
i2cset -f -y 0 0x2f 0x19 0xaa

Buildroot制作，工具U-start 已上传NAS，步骤如下

运行build.sh
选中U盘路径执行

root@ubuntu:~/U-start# ./build.sh 
保证U盘没有重要文件，U盘会全部格式化
您的磁盘为
sda		60G
sdb		29.6G
请输入您想分区的盘，格式为/dev/磁盘名称 (如 /dev/sda) :
/dev/sdb
/dev/sdb磁盘大小为29G,小于300G,可以正常使用
您想分区的磁盘名称为/dev/sdb, 确认请输入y,否则退出
请谨慎输入 (y,N)  y
确认
umount: /dev/sdb1: no mount point specified.
umount: /dev/sdb2: no mount point specified.
umount: /dev/sdb3: no mount point specified.
umount: /dev/sdb4: not mounted.
umount: /dev/sdb5: no mount point specified.

Welcome to fdisk (util-linux 2.34).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.


Command (m for help): Partition number (1,2, default 2): 
Partition 2 has been deleted.

Command (m for help): Selected partition 1
Partition 1 has been deleted.

Command (m for help): Partition type
   p   primary (0 primary, 0 extended, 4 free)
   e   extended (container for logical partitions)
Select (default p): Partition number (1-4, default 1): First sector (2048-62115839, default 2048): Last sector, +/-sectors or +/-size{K,M,G,T,P} (2048-62115839, default 62115839): 
Created a new partition 1 of type 'Linux' and of size 1000 MiB.

Command (m for help): Partition type
   p   primary (1 primary, 0 extended, 3 free)
   e   extended (container for logical partitions)
Select (default p): Partition number (2-4, default 2): First sector (2050048-62115839, default 2050048): Last sector, +/-sectors or +/-size{K,M,G,T,P} (2050048-62115839, default 62115839): 
Created a new partition 2 of type 'Linux' and of size 20 MiB.

Command (m for help): The partition table has been altered.
Calling ioctl() to re-read partition table.
Re-reading the partition table failed.: Device or resource busy

The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8).

/dev/sdb分区完成
############################################
/dev/sdb1正在进行格式化
mke2fs 1.45.5 (07-Jan-2020)
Creating filesystem with 256000 4k blocks and 64000 inodes
Filesystem UUID: 01668611-43eb-4819-af87-1c2728429910
Superblock backups stored on blocks: 
	32768, 98304, 163840, 229376

Allocating group tables: done                            
Writing inode tables: done                            
Writing superblocks and filesystem accounting information: done

/dev/sdb1格式化完成
/dev/sdb2正在进行格式化
mkfs.fat 4.1 (2017-01-24)
/dev/sdb2格式化完成
正在拷贝文件，请勿移动U盘
拷贝完成

将制作好的U盘插入被测板卡启动（支持3A5000,2K2000,2K1000,2K1500处理器）,root登录，空密码，ls查看有以下目录

Welcome to Buildroot
buildroot login: root
No mail.
# ls
2k0500	2k1500	3a5000	      dpdk-l2fwd    hugepage.sh
2k1000	2k2000	dpdk-bind.sh  dpdk-testpmd  setmrs.sh
说明：
//CPU型号目录下存放对应的igb_uio文件
//uio已经编译到内核
//hugepage.sh 设置大页内存
//setmrs.sh 无需设置
//dpdk-bin.sh 用于绑定接口
//dpdk-l2fwd,dpdk-testpmd 为测试程序

运行步骤

# 
# insmod 2k2000/igb_uio.ko 
[   33.543679] igb_uio: loading out-of-tree module taints kernel.
[   33.561711] igb_uio: Use MSIX interrupt by default
# ./hugepage.sh 
# ./dpdk-bind.sh -b igb_uio 04:00.0
[   51.039073] igb_uio 0000:04:00.0: mapping 1K dma=0x1a5c000 host=00000000f48b8029
[   51.046452] igb_uio 0000:04:00.0: unmapping 1K dma=0x1a5c000 host=00000000f48b8029
[   51.054242] pcieport 0000:00:0c.0: can't derive routing for PCI INT B
[   51.060668] igb_uio 0000:04:00.1: PCI INT B: no GSI
[   51.065656] igb_uio 0000:04:00.1: mapping 1K dma=0x1a5c000 host=00000000f48b8029
[   51.073031] igb_uio 0000:04:00.1: unmapping 1K dma=0x1a5c000 host=00000000f48b8029
# ./dpdk-bind.sh -b igb_uio 04:00.1
[   53.200501] pcieport 0000:00:0c.0: can't derive routing for PCI INT B
[   53.206934] igb_uio 0000:04:00.1: PCI INT B: no GSI
[   53.212105] igb_uio 0000:04:00.1: mapping 1K dma=0x1a5c000 host=00000000f48b8029
[   53.219470] igb_uio 0000:04:00.1: unmapping 1K dma=0x1a5c000 host=00000000f48b8029
# ./dpdk-bind.sh -s
0000:00:08.0 drivers ahci
0000:04:00.0 drivers igb_uio
0000:04:00.1 drivers igb_uio
0000:00:16.0 drivers ls-spi-pci
0000:00:09.0 drivers pcieport
0000:00:0a.0 drivers pcieport
0000:00:0b.0 drivers pcieport
0000:00:0c.0 drivers pcieport
0000:00:0d.0 drivers pcieport
0000:00:0f.0 drivers pcieport
0000:00:03.0 drivers stmmaceth
0000:00:03.1 drivers stmmaceth
0000:00:03.2 drivers stmmaceth
0000:00:04.0 drivers xhci_hcd
0000:00:19.0 drivers xhci_hcd

运行测试程序

# ./dpdk-testpmd -l 0,1 -- -i
EAL: Detected CPU lcores: 2
EAL: Detected NUMA nodes: 1
EAL: Detected static linkage of DPDK
EAL: Multi-process socket /var/run/dpdk/rte/mp_socket
EAL: Selected IOVA mode 'PA'
[  123.025759] igb_uio 0000:04:00.0: uio device registered with irq 45
EAL: Probe PCI driver: net_ngbe (8088:101) device: 0000:04:00.0 (socket 0)
[  123.172799] igb_uio 0000:04:00.1: uio device registered with irq 46
EAL: Probe PCI driver: net_ngbe (8088:101) device: 0000:04:00.1 (socket 0)
TELEMETRY: No legacy callbacks, legacy socket not created
Interactive-mode selected
testpmd: create a new mbuf pool <mb_pool_0>: n=155456, size=2176, socket=0
testpmd: preferred mempool ops selected: ring_mp_mc
Configuring Port 0 (socket 0)
Port 0: 8C:1C:DA:46:BF:00
Configuring Port 1 (socket 0)
Port 1: 8C:1C:DA:46:BF:01
Checking link statuses...
Done
testpmd> start