fwr310刷openwrt_全网首拆迅捷FWR310 V4.0 300M 路由硬改后刷华硕N14U

昨天16M闪和USB模块存到了。16M闪存已经请店家用编程器刷上了华硕N14U的编程器固件。路由焊上闪存后出现的问题是进不了192.168.1.1页面，指定网关为192.168.1.1可以进去了，显示是固件恢复页面，在这里刷入华硕的固件，显示成功并且路由自动重启，但是还是和前面一样(进不了192.168.1.1页面，指定网关为192.168.1.1可以进去了，显示是固件恢复页面)。TTL显示

U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)

SoC:MediaTek MT7620

DRAM:  Memory Testing.65536K OK. is 64 MB

relocate_code Pointer at: 83fac000

enable ephy clock...done. rf reg 29 = 5

SSC disabled.

spi_wait_nsec: 29

spi device id: c2 20 18 c2 20 (2018c220)

find flash: MX25L12805D

raspi_read: from:30000 len:1000

*** Warning - bad CRC, using default environment

______________________________________________________

|   ____                           ____              |

|  |  _ \ _ __ ___  __ _ _ __ ___ | __ )  _____  __  |

|  | | | | '__/ _ \/ _` | '_ ` _ \|  _ \ / _ \ \/ /  |

|  | |_| | | |  __/ (_| | | | | | | |_) | (_) >  

|  |____/|_|  \___|\__,_|_| |_| |_|____/ \___/_/\_\  |

|                                                    |

|                 DreamBox Team                      |

|           http://www.openwrt.org.cn                |

|              Board:Mercury MW305R                  |

|                                                    |

|          lintel            |

|____________________________________________________|

===============System Info==================

ASIC 7620_MP (Port5None)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Flash component: SPI Flash

CPU Speed: 580 MHZ

RAM Size:64 Mbytes

Build Date:Jan 29 2013  Time:15:41:44

============================================

GPIO Init:

UARTF_SHARE_MODE:GPIO

I2C_GPIO_MODE:GPIO

GPIO_MODE_REG status:0x1a311d

ReadyLED Bit:0x1

Please choose the operation:

1: Load system code to SDRAM via TFTP.

2: Load system code then write to Flash via TFTP.

3: Boot system code via Flash (default).

4: Entr boot command line interface.

7: Load Boot Loader code then write to Flash via Serial.

9: Load Boot Loader code then write to Flash via TFTP.

0

3: System Boot system code via Flash.

Press Reset button enter upgrade mode!

## Booting image at bc050000 ...

raspi_read: from:50000 len:40

Image Name:

Image Type:   MIPS Linux Kernel Image (lzma compressed)

Data Size:    12970108 Bytes = 12.4 MB

Load Address: 80000000

Entry Point:  8000c150

raspi_read: from:50040 len:c5e87c

Verifying Checksum ... OK

Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover

U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)

SoC:MediaTek MT7620

DRAM:  Memory Testing.65536K OK. is 64 MB

relocate_code Pointer at: 83fac000

enable ephy clock...done. rf reg 29 = 5

SSC disabled.

******************************

Software System Reset Occurred

******************************

spi_wait_nsec: 29

spi device id: c2 20 18 c2 20 (2018c220)

find flash: MX25L12805D

raspi_read: from:30000 len:1000

*** Warning - bad CRC, using default environment

______________________________________________________

|   ____                           ____              |

|  |  _ \ _ __ ___  __ _ _ __ ___ | __ )  _____  __  |

|  | | | | '__/ _ \/ _` | '_ ` _ \|  _ \ / _ \ \/ /  |

|  | |_| | | |  __/ (_| | | | | | | |_) | (_) >  

|  |____/|_|  \___|\__,_|_| |_| |_|____/ \___/_/\_\  |

|                                                    |

|                 DreamBox Team                      |

|           http://www.openwrt.org.cn                |

|              Board:Mercury MW305R                  |

|                                                    |

|          lintel            |

|____________________________________________________|

===============System Info==================

ASIC 7620_MP (Port5None)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Flash component: SPI Flash

CPU Speed: 580 MHZ

RAM Size:64 Mbytes

Build Date:Jan 29 2013  Time:15:41:44

============================================

GPIO Init:

UARTF_SHARE_MODE:GPIO

I2C_GPIO_MODE:GPIO

GPIO_MODE_REG status:0x1a311d

ReadyLED Bit:0x1

Please choose the operation:

1: Load system code to SDRAM via TFTP.

2: Load system code then write to Flash via TFTP.

3: Boot system code via Flash (default).

4: Entr boot command line interface.

7: Load Boot Loader code then write to Flash via Serial.

9: Load Boot Loader code then write to Flash via TFTP.

0

3: System Boot system code via Flash.

Press Reset button enter upgrade mode!

## Booting image at bc050000 ...

raspi_read: from:50000 len:40

Image Name:

Image Type:   MIPS Linux Kernel Image (lzma compressed)

Data Size:    12970108 Bytes = 12.4 MB

Load Address: 80000000

Entry Point:  8000c150

raspi_read: from:50040 len:c5e87c

Verifying Checksum ... OK

Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover

U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)

SoC:MediaTek MT7620

DRAM:  Memory Testing.65536K OK. is 64 MB

relocate_code Pointer at: 83fac000

enable ephy clock...done. rf reg 29 = 5

SSC disabled.

******************************

Software System Reset Occurred

******************************

spi_wait_nsec: 29

spi device id: c2 20 18 c2 20 (2018c220)

find flash: MX25L12805D

raspi_read: from:30000 len:1000

*** Warning - bad CRC, using default environment

______________________________________________________

|   ____                           ____              |

|  |  _ \ _ __ ___  __ _ _ __ ___ | __ )  _____  __  |

|  | | | | '__/ _ \/ _` | '_ ` _ \|  _ \ / _ \ \/ /  |

|  | |_| | | |  __/ (_| | | | | | | |_) | (_) >  

|  |____/|_|  \___|\__,_|_| |_| |_|____/ \___/_/\_\  |

|                                                    |

|                 DreamBox Team                      |

|           http://www.openwrt.org.cn                |

|              Board:Mercury MW305R                  |

|                                                    |

|          lintel            |

|____________________________________________________|

===============System Info==================

ASIC 7620_MP (Port5None)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Flash component: SPI Flash

CPU Speed: 580 MHZ

RAM Size:64 Mbytes

Build Date:Jan 29 2013  Time:15:41:44

============================================

GPIO Init:

UARTF_SHARE_MODE:GPIO

I2C_GPIO_MODE:GPIO

GPIO_MODE_REG status:0x1a311d

ReadyLED Bit:0x1

Please choose the operation:

1: Load system code to SDRAM via TFTP.

2: Load system code then write to Flash via TFTP.

3: Boot system code via Flash (default).

4: Entr boot command line interface.

7: Load Boot Loader code then write to Flash via Serial.

9: Load Boot Loader code then write to Flash via TFTP.

0

3: System Boot system code via Flash.

Press Reset button enter upgrade mode!

## Booting image at bc050000 ...

raspi_read: from:50000 len:40

Image Name:

Image Type:   MIPS Linux Kernel Image (lzma compressed)

Data Size:    12970108 Bytes = 12.4 MB

Load Address: 80000000

Entry Point:  8000c150

raspi_read: from:50040 len:c5e87c

Verifying Checksum ... OK

Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover

U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)

SoC:MediaTek MT7620

DRAM:  Memory Testing.65536K OK. is 64 MB

relocate_code Pointer at: 83fac000

enable ephy clock...done. rf reg 29 = 5

SSC disabled.

******************************

Software System Reset Occurred

******************************

spi_wait_nsec: 29

spi device id: c2 20 18 c2 20 (2018c220)

find flash: MX25L12805D

raspi_read: from:30000 len:1000

*** Warning - bad CRC, using default environment

______________________________________________________

|   ____                           ____              |

|  |  _ \ _ __ ___  __ _ _ __ ___ | __ )  _____  __  |

|  | | | | '__/ _ \/ _` | '_ ` _ \|  _ \ / _ \ \/ /  |

|  | |_| | | |  __/ (_| | | | | | | |_) | (_) >  

|  |____/|_|  \___|\__,_|_| |_| |_|____/ \___/_/\_\  |

|                                                    |

|                 DreamBox Team                      |

|           http://www.openwrt.org.cn                |

|              Board:Mercury MW305R                  |

|                                                    |

|          lintel            |

|____________________________________________________|

===============System Info==================

ASIC 7620_MP (Port5None)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Flash component: SPI Flash

CPU Speed: 580 MHZ

RAM Size:64 Mbytes

Build Date:Jan 29 2013  Time:15:41:44

============================================

GPIO Init:

UARTF_SHARE_MODE:GPIO

I2C_GPIO_MODE:GPIO

GPIO_MODE_REG status:0x1a311d

ReadyLED Bit:0x1

Please choose the operation:

1: Load system code to SDRAM via TFTP.

2: Load system code then write to Flash via TFTP.

3: Boot system code via Flash (default).

4: Entr boot command line interface.

7: Load Boot Loader code then write to Flash via Serial.

9: Load Boot Loader code then write to Flash via TFTP.

0

3: System Boot system code via Flash.

Press Reset button enter upgrade mode!

## Booting image at bc050000 ...

raspi_read: from:50000 len:40

Image Name:

Image Type:   MIPS Linux Kernel Image (lzma compressed)

Data Size:    12970108 Bytes = 12.4 MB

Load Address: 80000000

Entry Point:  8000c150

raspi_read: from:50040 len:c5e87c

Verifying Checksum ... OK

Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover

U-Boot 1.1.3 (Jan 29 2013 - 15:41:44)

SoC:MediaTek MT7620

DRAM:  Memory Testing.65536K OK. is 64 MB

relocate_code Pointer at: 83fac000

enable ephy clock...done. rf reg 29 = 5

SSC disabled.

******************************

Software System Reset Occurred

******************************

spi_wait_nsec: 29

spi device id: c2 20 18 c2 20 (2018c220)

find flash: MX25L12805D

raspi_read: from:30000 len:1000

*** Warning - bad CRC, using default environment

______________________________________________________

|   ____                           ____              |

|  |  _ \ _ __ ___  __ _ _ __ ___ | __ )  _____  __  |

|  | | | | '__/ _ \/ _` | '_ ` _ \|  _ \ / _ \ \/ /  |

|  | |_| | | |  __/ (_| | | | | | | |_) | (_) >  

|  |____/|_|  \___|\__,_|_| |_| |_|____/ \___/_/\_\  |

|                                                    |

|                 DreamBox Team                      |

|           http://www.openwrt.org.cn                |

|              Board:Mercury MW305R                  |

|                                                    |

|          lintel            |

|____________________________________________________|

===============System Info==================

ASIC 7620_MP (Port5None)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Flash component: SPI Flash

CPU Speed: 580 MHZ

RAM Size:64 Mbytes

Build Date:Jan 29 2013  Time:15:41:44

============================================

GPIO Init:

UARTF_SHARE_MODE:GPIO

I2C_GPIO_MODE:GPIO

GPIO_MODE_REG status:0x1a311d

ReadyLED Bit:0x1

Please choose the operation:

1: Load system code to SDRAM via TFTP.

2: Load system code then write to Flash via TFTP.

3: Boot system code via Flash (default).

4: Entr boot command line interface.

7: Load Boot Loader code then write to Flash via Serial.

9: Load Boot Loader code then write to Flash via TFTP.

0

3: System Boot system code via Flash.

Press Reset button enter upgrade mode!

## Booting image at bc050000 ...

raspi_read: from:50000 len:40

Image Name:

Image Type:   MIPS Linux Kernel Image (lzma compressed)

Data Size:    12970108 Bytes = 12.4 MB

Load Address: 80000000

Entry Point:  8000c150

raspi_read: from:50040 len:c5e87c