s5pv210的学习之路（20）x210的kernel编译

源代码见：https://github.com/jimingkang/news5pv210/tree/master/x210ii_kernel
(从九鼎qt_x210v3_160807.tar.bz2解压而来)

make ARCH=arm x210ii_initrd_defconfig
make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- -j 4

make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- zImage
make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- uImage

问题：
1）在编译嵌入式Linux内核时出现了以下错误提示：

Can’t use ‘defined(@array)’ (Maybe you should just omit the defined()?) at kernel/timeconst.pl line 373.

起初一头雾水，仔细看了错误提示后删掉了kernel/timeconst.pl 文件中 373行的
if (!defined(@val)) {
改为if (!@val) {
后，编译成功。
2）在start kernel..停止，由于我们用的是uart2，所以要修改linux配置

make menuconfig ->system type
由 (0) S3C UART to use for low-level messages
变为 (2) S3C UART to use for low-level messages
and make menuconfig ->kernel hacking
由 (0) S3C UART to use for low-level debug
变为 (2) S3C UART to use for low-level debug
以及可能的max8678电源问题（配置中multifunctional 项目中取消即可）
3)如果make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- uImage还是有start kernel..停止，尝试：
mkimage -A arm -O linux -T kernel -C none -a 30008000 -e 30008040 -d arch/arm/boot/zImage uImage

运行结果如下：
SMDKV210 jimmy# bdinfo
arch_number = 0x00000998
env_t = 0x00000000
boot_params = 0x30000100
DRAM bank = 0x00000000
-> start = 0x30000000
-> size = 0x10000000
DRAM bank = 0x00000001
-> start = 0x40000000
-> size = 0x10000000
ethaddr = 00:40:5C:26:0A:5B
ip_addr = 172.16.96.253
baudrate = 115200 bps

SMDKV210 jimmy# printenv
bootcmd=movi read kernel 30008000; movi read rootfs 30B00000 300000; bootm 30008000 30B00000
mtdpart=80000 400000 3000000
bootdelay=3
baudrate=115200
ethaddr=00:40:5c:26:0a:5b
serverip=172.16.96.215
gatewayip=172.16.96.215
netmask=255.255.254.0
ipaddr=172.16.96.253
bootargs=root=/dev/nfs rw nfsroot=172.16.96.215:/arm-nfs,proto=tcp,nfsvers=3,nolock ip=172.16.96.253:172.16.96.215:172.16.96.1:255.255.254.0::eth0:off console=ttySAC2,115200 init=/linuxrc

SMDKV210 jimmy# tftp 30008000 uImage
dm9000 i/o: 0x88000000, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 00:40:5c:26:0a:5b
operating at 100M full duplex mode
TFTP from server 172.16.96.215; our IP address is 172.16.96.253
Filename ‘uImage’.
Load address: 0x30008000
Loading: T ##
done
Bytes transferred = 7003336 (0x6adcc8)
SMDKV210 jimmy# bootm 30008000
get_format
——– 1 ——–

Booting kernel from Legacy Image at 30008000 …

Image Name:
Created: 2018-09-14 8:13:49 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 7003272 Bytes = 6.7 MB
Load Address: 30008000
Entry Point: 30008040
Verifying Checksum … OK
get_format
——– 1 ——–
XIP Kernel Image … OK
OK

Starting kernel …

Uncompressing Linux… done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.35.7+ (root@mo-cn-491.int.hrs.com) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #4 PREEMPT Fri Sep 14 16:11:54 CST 2018
[ 0.000000] CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: SMDKV210
[ 0.000000] @@@@@@@ atags_pointer not null
[ 0.000000] @@@@@@@linter#####boot_params:c0000100,mdesc->boot_params:40000002
[ 0.000000] Ignoring unrecognised tag 0x41001099
[ 0.000000]

<script type="math/tex; mode=display" id="MathJax-Element-1"></script>

<script type="math/tex; mode=display" id="MathJax-Element-2"></script>$cmdline:root=/dev/nfs rw nfsroot=172.16.96.215:/arm-nfs,proto=tcp,nfsvers=3,nolock ip=172.16.96.253:172.16.96.215:172.16.96.1:255.255.254.0::eth0:off console=ttySAC2,115200 init=/linuxrc
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU S5PV210/S5PC110 (id 0x43110220)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000 V=54000000
[ 0.000000] S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000
[ 0.000000] HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
[ 0.000000] sclk_dmc: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk_onenand: source is hclk_dsys (1), rate is 166750000
[ 0.000000] sclk: source is mout_mpll (6), rate is 66700000
[ 0.000000] sclk: source is mout_mpll (6), rate is 66700000
[ 0.000000] sclk: source is mout_mpll (6), rate is 66700000
[ 0.000000] sclk: source is mout_mpll (6), rate is 66700000
[ 0.000000] sclk_mixer: source is sclk_dac (0), rate is 54000000
[ 0.000000] sclk_spdif: source is sclk_audio (0), rate is 24000000
[ 0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_cam0: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_cam1: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_fimd: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 47642857
[ 0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000
[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 47642857
[ 0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000
[ 0.000000] sclk_mfc: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk_g2d: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk: source is sclk_a2m (0), rate is 200000000
[ 0.000000] sclk_csis: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_pwi: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_mdnie: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_mdnie_pwm: source is ext_xtal (0), rate is 24000000
[ 0.000000] s5pv210: 37748736 bytes system memory reserved for mfc at 0x312d1000
[ 0.000000] s5pv210: 37748736 bytes system memory reserved for mfc at 0x40000000
[ 0.000000] s5pv210: 25165824 bytes system memory reserved for fimc0 at 0x42400000
[ 0.000000] s5pv210: 10137600 bytes system memory reserved for fimc1 at 0x43c00000
[ 0.000000] s5pv210: 25165824 bytes system memory reserved for fimc2 at 0x445ab000
[ 0.000000] s5pv210: 25165824 bytes system memory reserved for jpeg at 0x45dab000
[ 0.000000] s5pv210: 4915200 bytes system memory reserved for fimd at 0x475ab000
[ 0.000000] s5pv210: 10485760 bytes system memory reserved for texstream at 0x47a5b000
[ 0.000000] s5pv210: 3379200 bytes system memory reserved for pmem_gpu1 at 0x4845b000
[ 0.000000] s5pv210: 8388608 bytes system memory reserved for g2d at 0x48794000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: root=/dev/nfs rw nfsroot=172.16.96.215:/arm-nfs,proto=tcp,nfsvers=3,nolock ip=172.16.96.253:172.16.96.215:172.16.96.1:255.255.254.0::eth0:off console=ttySAC2,115200 init=/linuxrc
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 256MB 256MB = 512MB total
[ 0.000000] Memory: 320756k/320756k available, 203532k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)
[ 0.000000] vmalloc : 0xe0800000 - 0xfc000000 ( 440 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc070e000 (7192 kB)
[ 0.000000] .text : 0xc070e000 - 0xc0db8000 (6824 kB)
[ 0.000000] .data : 0xc0db8000 - 0xc0e04980 ( 307 kB)
[ 0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:393
[ 0.000000] VIC @fd000000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd010000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd020000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd030000: id 0x00041192, vendor 0x41
[ 0.000000] mult[140737]
[ 0.000000] max_delta_ns[2937815369]
[ 0.000000] min_delta_ns[30517]
[ 0.000000] rate[32768]
[ 0.000000] HZ[256]
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttySAC2] enabled
[ 0.525094] Calibrating delay loop… 998.15 BogoMIPS (lpj=1949696)
[ 0.610486] pid_max: default: 32768 minimum: 301
[ 0.615136] Mount-cache hash table entries: 512
[ 0.619863] Initializing cgroup subsys debug
[ 0.623845] Initializing cgroup subsys cpuacct
[ 0.628259] Initializing cgroup subsys freezer
[ 0.632700] CPU: Testing write buffer coherency: ok
[ 0.639465] regulator: core version 0.5
[ 0.641959] NET: Registered protocol family 16
[ 0.651559] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.656355] pmstats at 00000000
[ 0.659480] Open OV2655 camema sensor
[ 0.796869] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.802983] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.810517] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.818055] smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
[ 0.825601] smdkv210_nand_io_init
[ 0.829262] S5PV210: Initializing architecture
[ 0.833605] s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0
[ 0.841734] s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000, tin=divclk, base 8
[ 0.850134] s3c24xx-pwm s3c24xx-pwm.2: tin at 66700000, tdiv at 66700000, tin=divclk, base 12
[ 0.858626] s3c24xx-pwm s3c24xx-pwm.3: tin at 66700000, tdiv at 66700000, tin=divclk, base 16
[ 0.867237] regulator: pd_audio_supply: 5000 mV normal
[ 0.872397] regulator: pd_cam_supply: 5000 mV normal
[ 0.877409] regulator: pd_tv_supply: 5000 mV normal
[ 0.882342] regulator: pd_lcd_supply: 5000 mV normal
[ 0.887370] regulator: pd_g3d_supply: 5000 mV normal
[ 0.892395] regulator: pd_mfc_supply: 5000 mV normal
[ 0.903341] bio: create slab at 0
[ 0.906341] SCSI subsystem initialized
[ 0.909717] usbcore: registered new interface driver usbfs
[ 0.915124] usbcore: registered new interface driver hub
[ 0.920434] usbcore: registered new device driver usb
[ 0.925769] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.930927] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.936297] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 0.941792] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.948202] Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc.
[ 0.955331] cfg80211: Calling CRDA to update world regulatory domain
[ 0.961612] Switching to clocksource clock_source_systimer
[ 0.971974] NET: Registered protocol family 2
[ 0.975043] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.982451] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.989274] TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
[ 0.996012] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.002068] TCP reno registered
[ 1.005177] UDP hash table entries: 256 (order: 1, 12288 bytes)
[ 1.011099] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[ 1.017536] NET: Registered protocol family 1
[ 1.021968] RPC: Registered udp transport module.
[ 1.026420] RPC: Registered tcp transport module.
[ 1.031096] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.077680] PMU: registered new PMU device of type 0
[ 1.081285] wifi power management
[ 1.084777] SMDKC110/V210 RTC, (c) 2010 Samsung Electronics
[ 1.090200] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[ 1.096276] smdkc110-rtc smdkc110-rtc: rtc core: registered s3c as rtc0
[ 1.102723] S5PV210 ADC driver, (c) 2010 Samsung Electronics
[ 1.108523] cpuidle: phy_regs_save:0x4f03a000
[ 1.112940] input: s3c-button as /devices/virtual/input/input0
[ 1.118454] s3c button Initialized!!
[ 1.122118] Loaded driver for PL330 DMAC-0 s3c-pl330
[ 1.126943] DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
[ 1.133072] Loaded driver for PL330 DMAC-1 s3c-pl330
[ 1.137941] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 1.144084] Loaded driver for PL330 DMAC-2 s3c-pl330
[ 1.148946] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 1.161537] ashmem: initialized
[ 1.163800] NTFS driver 2.1.29 [Flags: R/W].
[ 1.167486] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.174502] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 1.178690] msgmni has been set to 626
[ 1.184835] alg: No test for stdrng (krng)
[ 1.187510] io scheduler noop registered
[ 1.191396] io scheduler deadline registered
[ 1.195618] io scheduler cfq registered (default)
[ 1.200995] s3cfb s3cfb: [fb2] dma: 0x475ab000, cpu: 0xe1000000, size: 0x004b0000
[ 1.220602] Console: switching to colour frame buffer device 128x37
[ 1.233901] FIMD src sclk = 166750000
[ 1.237104] s3cfb s3cfb: registered successfully
[ 1.342260] x210 led driver
[ 1.410028] PA FB = 0x475AB000, bits per pixel = 32
[ 1.413463] screen width=1024 height=600 va=0xd75ab000 pa=0x475ab000
[ 1.419763] xres_virtual = 1024, yres_virtual = 1200, xoffset = 0, yoffset = 0
[ 1.426962] fb_size=4915200
[ 1.429729] Back frameBuffer[0].VAddr=d7803000 PAddr=47803000 size=2457600
[ 1.436907] s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
[ 1.445055] s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
[ 1.453109] s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
[ 1.461237] s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
[ 1.473514] brd: module loaded
[ 1.477287] loop: module loaded
[ 1.479017] pmem_gpu1: 1 init
[ 1.482291] Android kernel panic handler initialized (bind=kpanic)
[ 1.488534] S3C NAND Driver, (c) 2008 Samsung Electronics
[ 1.493541] Unknown NAND Device.
[ 1.496707] PPP generic driver version 2.4.2
[ 1.501079] PPP Deflate Compression module registered
[ 1.505920] PPP BSD Compression module registered
[ 1.516654] PPP MPPE Compression module registered
[ 1.520023] NET: Registered protocol family 24
[ 1.525994] dm9000 Ethernet Driver, V1.31
[ 1.529823] eth0: dm9000c at e08f4300,e08f8304 IRQ 42 MAC: 00:09:c0:ff:ec:48 (platform data)
[ 1.537014] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 1.543580] s5p-ehci s5p-ehci: s5pv210 EHCI
[ 1.547626] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 1.554704] s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
[ 1.568549] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[ 1.572549] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.579244] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.586435] usb usb1: Product: s5pv210 EHCI
[ 1.590585] usb usb1: Manufacturer: Linux 2.6.35.7+ ehci_hcd
[ 1.596223] usb usb1: SerialNumber: s5pv210
[ 1.600893] hub 1-0:1.0: USB hub found
[ 1.604137] hub 1-0:1.0: 1 port detected
[ 1.608208] Initializing USB Mass Storage driver…
[ 1.612961] usbcore: registered new interface driver usb-storage
[ 1.618840] USB Mass Storage support registered.
[ 1.623703] mice: PS/2 mouse device common for all mice
[ 1.628980] S5P Touchscreen driver, (c) 2008 Samsung Electronics
[ 1.634713] s3c-ts s3c-ts: Created Median filter len:5 coords:2 dec_threshold:6
[ 1.641902] s3c-ts s3c-ts: Created Mean filter len:3 coords:2
[ 1.647651] s3c-ts s3c-ts: Created Linear filter coords:2
[ 1.652993] s3c-ts s3c-ts: Created zoom filter coords:2
[ 1.658185] s3c-ts s3c-ts: 4 filter(s) initialized
[ 1.662976] S5P TouchScreen got loaded successfully : 12 bits
[ 1.668830] input: S5P TouchScreen as /devices/virtual/input/input1
[ 1.675409] using rtc device, s3c, for alarms
[ 1.679199] i2c /dev entries driver
[ 1.683157] Linux video capture interface: v2.00
[ 1.687370] gspca: main v2.9.0 registered
[ 1.691424] s3c-csis: Samsung MIPI-CSI2 driver probed successfully
[ 1.697493] mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics
[ 1.697500]
[ 1.706046] S3C JPEG Driver, (c) 2007 Samsung Electronics
[ 1.711052] JPEG driver for S5PV210
[ 1.715117] i2c i2c-1: attached s5p_ddc into i2c adapter successfully
[ 1.720965] S5PC11X HPD Driver, (c) 2009 Samsung Electronics
[ 1.726759] S5PC11X CEC Driver, (c) 2009 Samsung Electronics
[ 1.732730] usbcore: registered new interface driver uvcvideo
[ 1.737910] USB Video Class driver (v0.1.0)
[ 1.744021] device-mapper: uevent: version 1.0.3
[ 1.750251] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 1.757316] cpuidle: using governor ladder
[ 1.761360] cpuidle: using governor menu
[ 1.765233] sdhci: Secure Digital Host Controller Interface driver
[ 1.771340] sdhci: Copyright(c) Pierre Ossman
[ 1.775794] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)
[ 1.782270] s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133400000 Hz)
[ 1.788861] s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
[ 1.795776] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[ 1.802670] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133400000 Hz)
[ 1.809230] s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133400000 Hz)
[ 1.815814] s3c-sdhci s3c-sdhci.1: clock source 2: sclk_mmc (47642857 Hz)
[ 1.892920] wifi power enabled
[ 1.894582] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
[ 1.901578] s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133400000 Hz)
[ 1.908119] s3c-sdhci s3c-sdhci.2: clock source 1: hsmmc (133400000 Hz)
[ 1.914714] s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)
[ 1.921581] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[ 1.928522] s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz)
[ 1.935072] s3c-sdhci s3c-sdhci.3: clock source 1: hsmmc (133400000 Hz)
[ 1.941661] s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)
[ 1.948519] mmc3: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
[ 1.956063] usbcore: registered new interface driver hiddev
[ 1.961050] usbcore: registered new interface driver usbhid
[ 1.966520] usbhid: USB HID core driver
[ 1.970746] logger: created 64K log ‘log_main’
[ 1.974886] logger: created 256K log ‘log_events’
[ 1.979537] logger: created 64K log ‘log_radio’
[ 1.984046] logger: created 64K log ‘log_system’
[ 1.993116] No device for DAI WM8976 HiFi
[ 1.995714] s3c64xx_iis_dai_init:s3c64xx-i2s0
[ 2.000224] s3c64xx_iis_dev_probe:id0 !!!
[ 2.004091] s3c64xx_iis_dai_init:s3c64xx-i2s1
[ 2.008767] WM8976 Audio Codec 0.4wm8976_probe: i2c_master_send
[ 2.014512] wm8976_init
[ 2.068581] usb 1-1: new high speed USB device using s5p-ehci and address 2
[ 2.074843] mmc0: new high speed MMC card at address 0001
[ 2.079683] mmcblk0: mmc0:0001 004GE0 3.68 GiB
[ 2.084238] mmcblk0: p1 p2 p3 p4
[ 2.202805] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 2.208061] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.215150] usb 1-1: Product: USB2.0 Hub
[ 2.219796] hub 1-1:1.0: USB hub found
[ 2.223057] hub 1-1:1.0: 4 ports detected
[ 2.578207] mmc2: new high speed SDHC card at address 21e1
[ 2.582415] mmcblk1: mmc2:21e1 APPSD 7.61 GiB
[ 2.586963] mmcblk1: p1
[ 2.789021] s3c_idma_preallocate_buffer: VA-e0940000 PA-C0000000 163840bytes
[ 2.795153] s3c_preallocate_dma_buffer: VA-ff007000, PA-4F3A0000, 131072bytes
[ 2.801965] asoc: WM8976 HiFi <-> s3c64xx-i2s0 mapping ok
[ 2.810594] ALSA device list:
[ 2.812102] #0: smdkc1000 (WM8976)
[ 2.815689] GACT probability NOT on
[ 2.819117] Mirror/redirect action on
[ 2.822754] u32 classifier
[ 2.825420] Actions configured
[ 2.828815] Netfilter messages via NETLINK v0.30.
[ 2.833553] nf_conntrack version 0.5.0 (5011 buckets, 20044 max)
[ 2.839628] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 2.846847] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 2.854732] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 2.861535] ctnetlink v0.93: registering with nfnetlink.
[ 2.866277] xt_time: kernel timezone is -0000
[ 2.872646] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.876585] arp_tables: (C) 2002 David S. Miller
[ 2.881274] TCP cubic registered
[ 2.884298] NET: Registered protocol family 10
[ 2.890523] lo: Disabled Privacy Extensions
[ 2.897896] Mobile IPv6
[ 2.898863] IPv6 over IPv4 tunneling driver
[ 2.904560] sit0: Disabled Privacy Extensions
[ 2.910252] ip6tnl0: Disabled Privacy Extensions
[ 2.914749] NET: Registered protocol family 17
[ 2.917849] NET: Registered protocol family 15
[ 2.922281] lib80211: common routines for IEEE802.11 drivers
[ 2.927950] ThumbEE CPU extension supported.
[ 2.932226] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 2.940302] regulator_init_complete: disabling pd_mfc_supply
[ 2.945392] regulator_init_complete: disabling pd_tv_supply
[ 2.950931] regulator_init_complete: disabling pd_cam_supply
[ 2.956606] smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
[ 2.962556] smdkc110-rtc smdkc110-rtc: setting system clock to 2010-01-01 12:05:35 UTC (1262347535)
[ 2.973016] FIMC0 registered successfully
[ 2.976840] FIMC1 registered successfully
[ 2.980938] FIMC2 registered successfully
[ 2.983586] <6>S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
[ 2.990249] s5p-tvout s5p-tvout: hpd status is cable removed
[ 3.001295] DBUG_PORT must not use AFC!
[ 3.004644] Freeing init memory: 7192K
Loading, please wait…
depmod: chdir(2.6.35.7+): No such file or directory
Begin: Loading essential drivers… …
Done.
Begin: Running /scripts/init-premount …
Done.
chvt: can’t open console
modprobe: chdir(2.6.35.7+): No such file or directory
modprobe: chdir(2.6.35.7+): No such file or directory
Spawning shell within the initramfs
/bin/sh: can’t access tty; job control turned off
(initramfs):/#