基于STM32的中断按键控制LED亮灭proteus仿真

硬件设计

链接：https://pan.baidu.com/s/1_A7NGQac34M5IelY508WVg
提取码：cot7

仿真图如下所示：

程序设计

#include"stm32f10x.h"

#define Led_Red_On				GPIO_ResetBits(GPIOC,GPIO_Pin_1)
#define Led_Red_Off				GPIO_SetBits(GPIOC,GPIO_Pin_1)
#define Led_Red_Toggle		GPIOC -> ODR ^= GPIO_Pin_1

#define Led_Green_On			GPIO_ResetBits(GPIOC,GPIO_Pin_2)
#define Led_Green_Off			GPIO_SetBits(GPIOC,GPIO_Pin_2)
#define Led_Green_Toggle	GPIOC -> ODR ^= GPIO_Pin_2

#define Led_Blue_On				GPIO_ResetBits(GPIOC,GPIO_Pin_3)
#define Led_Blue_Off			GPIO_SetBits(GPIOC,GPIO_Pin_3)
#define Led_Blue_Toggle		GPIOC -> ODR ^= GPIO_Pin_3

void Blue_Flash()      //蓝灯闪烁
{
	int i;
	void delay(unsigned int t);
	for(i=3;i>0;i--)
	{			    
					Led_Blue_Toggle;delay(100000);		
	}
}

void Led_Configration()       
{
	GPIO_InitTypeDef GPIO_InitStruct;
	
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC,ENABLE);
	
	GPIO_InitStruct.GPIO_Pin = (GPIO_Pin_1 | GPIO_Pin_2 | GPIO_Pin_3);    
	GPIO_InitStruct.GPIO_Mode = GPIO_Mode_Out_PP;			
	GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;			
	GPIO_Init(GPIOC,&GPIO_InitStruct);	
	
	Led_Red_Off;
	Led_Green_Off;
	Led_Blue_Off;
}

void delay(unsigned int t)      
{
		while(t--);
}

void EXTI_Configration()      
{
		EXTI_InitTypeDef EXTI_InitStructure; 
		RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_AFIO ,ENABLE); 
		GPIO_EXTILineConfig(GPIO_PortSourceGPIOA,GPIO_PinSource0);
		GPIO_EXTILineConfig(GPIO_PortSourceGPIOA,GPIO_PinSource13); 
	
		EXTI_InitStructure.EXTI_Line = EXTI_Line0 | EXTI_Line13; 
		EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
		EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising; 
		EXTI_InitStructure.EXTI_LineCmd = ENABLE;
		EXTI_Init(&EXTI_InitStructure); 
}

void NVIC_Configration()       
{
		NVIC_InitTypeDef NVIC_InitStructure; 
		
		NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); 
	
		NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;
		NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1; 
		NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1; 
		NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; 
		NVIC_Init(&NVIC_InitStructure); 
		
		NVIC_InitStructure.NVIC_IRQChannel = EXTI15_10_IRQn;
		NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2; 
		NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1; 
		NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; 
		NVIC_Init(&NVIC_InitStructure);

		
	
}
int main()
	
{
	Led_Configration();
	EXTI_Configration();
	NVIC_Configration();
	
	while(1)                          //控制红绿灯交替闪烁
	{
			Led_Red_Toggle;
			delay(100000);
		  Led_Green_Toggle;
			
	}
}

void EXTI0_IRQHandler()               //按键1进入EXTI0中断控制蓝灯闪烁
{
		
		 if(EXTI_GetITStatus(EXTI_Line0) != RESET) 
		 {
					EXTI_ClearITPendingBit(EXTI_Line0); 
			    Blue_Flash();
		 }
}
	
void EXTI15_10_IRQHandler()             //按下KEY2进入EXTI13通道使蓝灯状态取反
{
		
		 if(EXTI_GetITStatus(EXTI_Line13) != RESET) 
		 {
					EXTI_ClearITPendingBit(EXTI_Line13); 
						Led_Blue_Toggle;
		 }	
}