H3C 交换机IRF堆叠配置

配置注意事项
    与IRF-Port1口绑定的IRF物理端口只能和邻居成员设备IRF-Port2口上绑定的IRF物理端口相连，本设备上与IRF-Port2口绑定的IRF物理端口只能和邻居成员设备IRF-Port1口上绑定的IRF物理端口相连。否则，不能形成IRF。

配置步骤
   Device A的配置
       (1) Device A保留缺省编号为1，不需要进行配置
       (2) 创建IRF端口2，并将它与物理端口Ten-GigabitEthernet 1/0/25和Ten-GigabitEthernet 1/0/26绑定
          <DeviceA> system-view
           [DeviceA] interface ten-gigabitethernet 1/0/25
           [DeviceA-Ten-GigabitEthernet1/0/25] shutdown
           [DeviceA-Ten-GigabitEthernet1/0/25] quit
           [DeviceA] interface ten-gigabitethernet 1/0/26
           [DeviceA-Ten-GigabitEthernet1/0/26] shutdown
           [DeviceA-Ten-GigabitEthernet1/0/26] quit
           [DeviceA] irf-port 1/2
           [DeviceA-irf-port1/2] port group interface ten-gigabitethernet1/0/25
           [DeviceA-irf-port1/2] port group interface ten-gigabitethernet1/0/26
           [DeviceA-irf-port1/2] quit
           [DeviceA] interface ten-gigabitethernet 1/0/25
           [DeviceA-Ten-GigabitEthernet1/0/25] undo shutdown
           [DeviceA-Ten-GigabitEthernet1/0/25] quit
           [DeviceA] interface ten-gigabitethernet 1/0/26
           [DeviceA-Ten-GigabitEthernet1/0/26] undo shutdown
          [DeviceA-Ten-GigabitEthernet1/0/26] quit
      (3) 配置Device A的成员优先级为32，以保证其成为IRF中的主设备。
          [DeviceA] irf member 1 priority 32
      (4) 保存配置
          [DeviceA] save force

   Device B的配置
       (1) 设置Device B的成员编号为2，并重启设备使配置生效。
           <DeviceB> system-view
          [DeviceB] irf member 1 renumber 2
          Warning: Renumbering the switch number may result in configuration change or loss. Continue? [Y/N]:y
          [DeviceB] quit
         <DeviceB>  reboot
      (2) 创建设备的IRF端口1，并将它与物理端口Ten-GigabitEthernet 2/0/25和Ten-GigabitEthernet 2/0/26绑定
         [DeviceB] interface ten-gigabitethernet 2/0/25
         [DeviceB-Ten-GigabitEthernet2/0/25] shutdown
         [DeviceB-Ten-GigabitEthernet2/0/25] quit
         [DeviceB] interface ten-gigabitethernet 2/0/26
         [DeviceB-Ten-GigabitEthernet2/0/26] shutdown
         [DeviceB-Ten-GigabitEthernet2/0/26] quit
         [DeviceB] irf-port 2/1
         [DeviceB-irf-port2/1] port group interface ten-gigabitethernet2/0/25
         [DeviceB-irf-port2/1] port group interface ten-gigabitethernet2/0/26
         [DeviceB-irf-port2/1] quit
         [DeviceB] interface ten-gigabitethernet 2/0/25
         [DeviceB-Ten-GigabitEthernet2/0/25] undo shutdown
         [DeviceB-Ten-GigabitEthernet2/0/25] quit
         [DeviceB] interface ten-gigabitethernet 2/0/26
         [DeviceB-Ten-GigabitEthernet2/0/26] undo shutdown
         [DeviceB-Ten-GigabitEthernet2/0/26] quit
      (3) 保存配置
         [DeviceB] save force
      (4) 端口连接Device A和Device B之间的IRF端口(可以采用交叉方式连接)

激活配置
    激活DeviceA的IRF端口配置。
       [DeviceA] irf-port-configuration active
    激活DeviceB的IRF端口配置。
        [DeviceB] irf-port-configuration active
*可以通过断电交换机，先通电DeviceA ，随后DeviceB加电，设备自检启动完成，两台设备间将会进行Master竞选，竞选失败的一方将自动重启，重启完成后，IRF形成，系统名称统一为DeviceA。

验证配置
   验证IRF建立成功：
    <DeviceA> display irf
      MemberID  Slot      Role    Priority       CPU-Mac         Description
             *+1        0     Master      32        0210-fc01-0000          ---
               2         0     Standby     1         0210-fc02-0000          ---
        ● indicates the device is the master.
        ● indicates the device through which the user logs in.
       The Bridge MAC of the IRF is: 3822-d60f-2800
       Auto upgrade                : yes
       Mac persistent              : always
       Domain ID                   : 0
       Auto merge                  : yes
     从命令行的显示看，当前两台设备IRF成功建立。