路由与交换-华为eNSP-isis配置

一、要求

客户网络所有路由器路由协议要求启用IS-IS，使全网路由可达。
1.全部IS-IS进程号统一为100，
2.其中R1在Area49.0001区域为DIS，优先级修改为100
3.R4与R5之间要求采用P2P网络类型
4.R5引入直连链路192.168.X.X，
5.要求R1访问Area49.0002走最优路径。
  R1能够通过明细路由到达49.0002即可---实现L1-2向L1路由器通告L2的明细
  在L1-2设备上进行 路由渗透（L2--->L1）

二、配置

1.接口配置

2.区域配置

[R1]isis 100
[R1-isis-100]network-entity 49.0001.0000.0000.0001.00
[R1-isis-100]is-level level-1
[R]int g0/0/0
[R1-GigabitEhernet0/0/0]isis enable 100

[R2]isis 100
[R2-isis-100]network-entity 49.0001.0000.0000.0002.00
[R2-isis-100]is-level level-1-2
[R2]int g0/0/0
[R2-GigabitEthernet0/0/0]isis enable 100
[R2]int g0/0/1
[R2-GigabitEthernet0/0/1]isis enable 100

[R3]isis 100
[R3-isis-100]network-entity 49.0001.0000.0000.0003.00
[R3-isis-100]is-level level-1-2
[R3]int g0/0/0
[R3-GigabitEthernet0/0/0]isis enable 100
[R3]int s0/0/0
[R3-Serial0/0/0]isis enable 100

[R4]isis 100
[R4-isis-100]network-entity 49.0002.0000.0000.0004.00
[R4-isis-100]is-level level-2
[R4]int g0/0/1
[R4-GigabitEthernet0/0/1]isis enable 100
[R4]int s0/0/1
[R4-Serial0/0/0]isis enable 100

[R5]isis 100
[R5-isis-100]network-entity 49.0002.0000.0000.0005.00
[R5-isis-100]is-level level-2
[R5]int g0/0/0
[R5-GigabitEthernet0/0/0]isis enable 100
[R5]int g0/0/1
[R5-GigabitEthernet0/0/1]isis enable 100
[R5]int g0/0/2
[R5-GigabitEthernet0/0/2]isis enable 100
[R5]int g0/0/3
[R5-GigabitEthernet0/0/2]isis enable 100

3.修改优先级

[R1]int g0/0/0
[R1-GigabitEthernet0/0/0]isis dis-priority 110

4.修改为P2P网络类型

[R4]int g0/0/0	
[R4-GigabitEthernet0/0/0]isis circuit-type p2p

[R5]int g0/0/0
[R5-GigabitEthernet0/0/0]isis circuit-type p2p

5.引入直连链路

[R5]isis 100
[R5-isis-100]import-route  direct 

6.明细路由，路由渗透

[R2]isis 100
[R2-isis-100]import-route  isis level-2 into level-1 
[R2-isis-100]aut-cost enable    //根据接口带宽自动计算开销值

[R3]isis 100
[R3-isis-100]import-route  isis level-2 into level-1 
[R3-isis-100]aut-cost enable    //根据接口带宽自动计算开销值

[R1]isis 100
[R1-isis-100]aut-cost enable    //根据接口带宽自动计算开销值

三、测试