LVS-DR 负载均衡集群搭建
1.LVS-DR 负载均衡集群概述
1.1 原理
客户端向目标vip发出请求,lvs接收 ,LVS根据负载均衡算法选择一台活跃的的节点,将此节点的ip所在网卡的mac地址作为目标mac地址,发送到局域网里
节点在局域网中收到这个帧,拆开后发现目标IP(VIP)与本地匹配,于是处理这个报文.随后重新封装报文,发送到局域网.此时IP包的目标ip是客户端,源ip是自己的vip地址。
2… LVS-DR 负载均衡集群搭建实验
实验环境
一台调度器: VM1:192.168.100:41
二台WEB服务器集群池:192.168.100.42、192.168.100.43
一台NFS共享服务器:192.168.100.44
2.1 在调度器配置:192.168.100.21
【1】配置虚拟IP地址(VIP)
[root@localhost ~]# cd /etc/sysconfig/network-scripts/
[root@localhost network-scripts]# cp ifcfg-ens33 ifcfg-ens33:0
[root@localhost network-scripts]# vi ifcfg-ens33:0
NAME=ens33:0
DEVICE=ens33:0
ONBOOT=yes
IPADDR=192.168.100.10
NETMASK=255.255.255.255
[root@localhost network-scripts]# ifup ifcfg-ens33:0 ##启动ens33.0网口
[root@localhost network-scripts]# ifconfig
【2】调整/proc响应参数
对于 DR 群集模式来说,由于 LVS 负载调度器和各节点需要共用 VIP 地址,应该关闭 Linux 内核的重定向参数响应服务器不是一台路由器,那么它不会发送重定向,所以可以关闭该功能
[root@localhost network-scripts]# vi /etc/sysctl.conf
net.ipv4.conf.all.send_redirects = 0
net.ipv4.conf.default.send_redirects = 0
net.ipv4.conf.ens33.send_redirects = 0
[root@localhost network-scripts]# sysctl -p ###生效
net.ipv4.conf.all.send_redirects = 0
net.ipv4.conf.default.send_redirects = 0
net.ipv4.conf.ens33.send_redirects = 0
【3】配置负载分配策略
[root@localhost /]# ipvsadm -v
[root@localhost ~]# modprobe ip_vs
[root@localhost ~]# cat /proc/net/ip_vs
[root@localhost ~]#yum -y install ipvsadm
[root@localhost ~]#ipvsadm -A -t 192.168.100.10:80 -s rr
[root@localhost ~]#ipvsadm -a -t 192.168.100.10:80 -r 192.168.100.42:80 -g -w 1
[root@localhost ~]#ipvsadm -a -t 192.168.100.10:80 -r 192.168.100.43:80 -g -w 1
[root@localhost network-scripts]# ipvsadm-save
[root@localhost network-scripts]# systemctl enable ipvsadm
2.2 配置存储服务器:192.168.100.44
rpm -q nfs-utils ###如果没装,yum -y install nfs-utils
rpm -q rpcbind ###如果没装,yum -y install rpcbind
[root@localhost ~]# systemctl start nfs
[root@localhost ~]# systemctl start rpcbind
[root@localhost ~]# vi /etc/exports
/opt/51xit 192.168.100.0/24 (rw,sync)
/opt/52xit 192.168.100.0/24 (rw,sync)
[root@localhost ~]# systemctl restart nfs
[root@localhost ~]# systemctl restart rpcbind
[root@localhost ~]# systemctl enable nfs
[root@localhost ~]# systemctl enable rpcbind
[root@localhost ~]# mkdir /opt/51xit /opt/52xit
[root@localhost ~]# echo "this is 51xit" >/opt/51xit/index.html
[root@localhost ~]# echo "this is 52xit" >/opt/52xit/index.html
2.3 配置节点服务器:192.168.100.42
【1】配置虚拟IP地址
[root@localhost ~]# cd /etc/sysconfig/network-scripts/
[root@localhost network-scripts]# cp ifcfg-lo ifcfg-lo:0
[root@localhost network-scripts]# vi ifcfg-lo:0
DEVICE=lo:0
IPADDR=192.168.100.10
NETMASK=255.255.255.255
ONBOOT=yes
[root@localhost network-scripts]# ifup lo:0
[root@localhost network-scripts]# ifconfig
[root@localhost network-scripts]# vi /etc/rc.local
/sbin/route add -host 192.168.100.10 dev lo:0
[root@localhost network-scripts]# route add -host 192.168.100.10 dev lo:0
【2】调整/proc响应参数
[root@localhost network-scripts]# vi /etc/sysctl.conf
net.ipv4.conf.all.arp_ignore = 1
net.ipv4.conf.all.arp_announce = 2
net.ipv4.conf.default.arp_ignore = 1
net.ipv4.conf.default.arp_announce = 2
net.ipv4.conf.lo.arp_ignore = 1
net.ipv4.conf.lo.arp_announce = 2
[root@localhost network-scripts]# sysctl -p
【3】安装httpd 挂载测试页
[root@localhost ~]# showmount -e 192.168.100.44 ####如果还没发布,请到存储服务器发布下,exportfs -rv
Export list for 192.168.100.44:
/opt/51xit (everyone)
/opt/52xit (everyone)
[root@localhost ~]# yum -y install httpd
[root@localhost ~]# mount 192.168.100.44:/opt/51xit /var/www/html/
[root@localhost ~]# vi /etc/fstab
192.168.100.44:/opt/51xit/ /var/www/html/ nfs rw,tcp,intr 0 1 ###开机自动挂载,注意格式对齐
[root@localhost ~]# systemctl start httpd
[root@localhost ~]# systemctl enable httpd
###登录192.168.100.42测试网站是否正常####
2.4 配置节点服务器:192.168.100.43
【1】配置虚拟IP地址
[root@localhost ~]# cd /etc/sysconfig/network-scripts/
[root@localhost network-scripts]# cp ifcfg-lo ifcfg-lo:0
[root@localhost network-scripts]# vi ifcfg-lo:0
DEVICE=lo:0
IPADDR=192.168.100.10
NETMASK=255.255.255.255
ONBOOT=yes
[root@localhost network-scripts]# ifup lo:0
[root@localhost network-scripts]# ifconfig
[root@localhost network-scripts]# vi /etc/rc.local
/sbin/route add -host 192.168.100.10 dev lo:0
[root@localhost network-scripts]# route add -host 192.168.100.10 dev lo:0
【2】调整/proc响应参数
[root@localhost network-scripts]# vi /etc/sysctl.conf
net.ipv4.conf.all.arp_ignore = 1
net.ipv4.conf.all.arp_announce = 2
net.ipv4.conf.default.arp_ignore = 1
net.ipv4.conf.default.arp_announce = 2
net.ipv4.conf.lo.arp_ignore = 1
net.ipv4.conf.lo.arp_announce = 2
[root@localhost network-scripts]# sysctl -p
【3】安装httpd 挂载测试页
[root@localhost ~]# showmount -e 192.168.100.44 ####如果还没发布,请到存储服务器发布下,exportfs -rv
Export list for 192.168.100.44:
/opt/accp (everyone)
/opt/bdqn (everyone)
[root@localhost ~]# yum -y install httpd
[root@localhost ~]# mount 192.168.100.44:/opt/52xit /var/www/html/
[root@localhost ~]# vi /etc/fstab
192.168.100.44:/opt/52xit/ /var/www/html/ nfs rw,tcp,intr 0 1 ###开机自动挂载,注意格式对齐
[root@localhost ~]# systemctl start httpd
[root@localhost ~]# systemctl enable httpd
登录192.168.100.43测试网站是否正常
2.5 测试网站
登录192.168.100.10测试一下