AS608光学指纹识别模块 智能锁/考勤门禁开发/指纹采集模块

已于 2022-07-08 22:46:45 修改
阅读量838 收藏 12
点赞数
文章标签： 单片机 c语言 stm32
于 2021-12-13 20:42:26 首次发布
原文链接：https://www.arduino.cn/thread-92416-3-1.html
版权

一、注册指纹

/*
  【Arduino】168种传感器模块系列实验（资料+代码+图形+仿真）
  实验一百五十：AS608光学指纹识别模块 智能锁/考勤门禁开发/指纹采集模块
  
  实验之二：输入序号，注册指纹示例
  安装库：IDE—工具—管理库—搜索Adafruit-Fingerprint-Sensor-Library—安装
  实验接线：
  Vi      +3.3V（请勿接3.3V以上电源，否则烧毁模块！）
  TX      2
  RX      3
  GND    GND
*/

#include <Adafruit_Fingerprint.h>

// On Leonardo/Micro or others with hardware serial, use those! #0 is green wire, #1 is white
// uncomment this line:
// #define mySerial Serial1

// For UNO and others without hardware serial, we must use software serial...
// pin #2 is IN from sensor (GREEN wire)
// pin #3 is OUT from arduino  (WHITE wire)
// comment these two lines if using hardware serial
SoftwareSerial mySerial(2, 3);

Adafruit_Fingerprint finger = Adafruit_Fingerprint(&mySerial);

uint8_t id;

void setup()  
{
  Serial.begin(9600);
  while (!Serial);  // For Yun/Leo/Micro/Zero/...
  delay(100);
  Serial.println("\n\nAdafruit Fingerprint sensor enrollment");

  // 设置传感器串行端口的数据速率
  finger.begin(57600);
  
  if (finger.verifyPassword()) {
    Serial.println("Found fingerprint sensor!");
  } else {
    Serial.println("Did not find fingerprint sensor ");
    while (1) { delay(1); }
  }
}

uint8_t readnumber(void) {
  uint8_t num = 0;
  
  while (num == 0) {
    while (! Serial.available());
    num = Serial.parseInt();
  }
  return num;
}

void loop()                      // 循环执行
{
  Serial.println("Ready to enroll a fingerprint!");
  Serial.println("lease type in the ID # (from 1 to 127) you want to save this finger as...");
  id = readnumber();
  if (id == 0) {// ID #0 not allowed, try again!
     return;
  }
  Serial.print("Enrolling ID #");
  Serial.println(id);
  
  while (!  getFingerprintEnroll() );
}

uint8_t getFingerprintEnroll() {

  int p = -1;
  Serial.print("Waiting for valid finger to enroll as #"); Serial.println(id);
  while (p != FINGERPRINT_OK) {
    p = finger.getImage();
    switch (p) {
    case FINGERPRINT_OK:
      Serial.println("Image taken");
      break;
    case FINGERPRINT_NOFINGER:
      Serial.println(".");
      break;
    case FINGERPRINT_PACKETRECIEVEERR:
      Serial.println("Communication error");
      break;
    case FINGERPRINT_IMAGEFAIL:
      Serial.println("Imaging error");
      break;
    default:
      Serial.println("Unknown error");
      break;
    }
  }

  // OK success!

  p = finger.image2Tz(1);
  switch (p) {
    case FINGERPRINT_OK:
      Serial.println("Image converted");
      break;
    case FINGERPRINT_IMAGEMESS:
      Serial.println("Image too messy");
      return p;
    case FINGERPRINT_PACKETRECIEVEERR:
      Serial.println("Communication error");
      return p;
    case FINGERPRINT_FEATUREFAIL:
      Serial.println("Could not find fingerprint features");
      return p;
    case FINGERPRINT_INVALIDIMAGE:
      Serial.println("Could not find fingerprint features");
      return p;
    default:
      Serial.println("Unknown error");
      return p;
  }
  
  Serial.println("Remove finger");
  delay(2000);
  p = 0;
  while (p != FINGERPRINT_NOFINGER) {
    p = finger.getImage();
  }
  Serial.print("ID "); Serial.println(id);
  p = -1;
  Serial.println("lace same finger again");
  while (p != FINGERPRINT_OK) {
    p = finger.getImage();
    switch (p) {
    case FINGERPRINT_OK:
      Serial.println("Image taken");
      break;
    case FINGERPRINT_NOFINGER:
      Serial.print(".");
      break;
    case FINGERPRINT_PACKETRECIEVEERR:
      Serial.println("Communication error");
      break;
    case FINGERPRINT_IMAGEFAIL:
      Serial.println("Imaging error");
      break;
    default:
      Serial.println("Unknown error");
      break;
    }
  }

  // OK success!

  p = finger.image2Tz(2);
  switch (p) {
    case FINGERPRINT_OK:
      Serial.println("Image converted");
      break;
    case FINGERPRINT_IMAGEMESS:
      Serial.println("Image too messy");
      return p;
    case FINGERPRINT_PACKETRECIEVEERR:
      Serial.println("Communication error");
      return p;
    case FINGERPRINT_FEATUREFAIL:
      Serial.println("Could not find fingerprint features");
      return p;
    case FINGERPRINT_INVALIDIMAGE:
      Serial.println("Could not find fingerprint features");
      return p;
    default:
      Serial.println("Unknown error");
      return p;
  }
  
  // OK converted!
  Serial.print("Creating model for #");  Serial.println(id);
  
  p = finger.createModel();
  if (p == FINGERPRINT_OK) {
    Serial.println("rints matched!");
  } else if (p == FINGERPRINT_PACKETRECIEVEERR) {
    Serial.println("Communication error");
    return p;
  } else if (p == FINGERPRINT_ENROLLMISMATCH) {
    Serial.println("Fingerprints did not match");
    return p;
  } else {
    Serial.println("Unknown error");
    return p;
  }   
  
  Serial.print("ID "); Serial.println(id);
  p = finger.storeModel(id);
  if (p == FINGERPRINT_OK) {
    Serial.println("Stored!");
  } else if (p == FINGERPRINT_PACKETRECIEVEERR) {
    Serial.println("Communication error");
    return p;
  } else if (p == FINGERPRINT_BADLOCATION) {
    Serial.println("Could not store in that location");
    return p;
  } else if (p == FINGERPRINT_FLASHERR) {
    Serial.println("Error writing to flash");
    return p;
  } else {
    Serial.println("Unknown error");
    return p;
  }   
}

二、匹配指纹

/*
  【Arduino】168种传感器模块系列实验（资料+代码+图形+仿真）
  实验一百五十：AS608光学指纹识别模块 智能锁/考勤门禁开发/指纹采集模块

  实验之三：查找一个匹配的指纹
  安装库：IDE—工具—管理库—搜索Adafruit-Fingerprint-Sensor-Library—安装
  实验接线：
  Vi      +3.3V（请勿接3.3V以上电源，否则烧毁模块！）
  TX      2
  RX      3
  GND    GND
*/

#include <Adafruit_Fingerprint.h>

// On Leonardo/Micro or others with hardware serial, use those! #0 is green wire, #1 is white
// uncomment this line:
// #define mySerial Serial1

// For UNO and others without hardware serial, we must use software serial...
// pin #2 is IN from sensor (GREEN wire)
// pin #3 is OUT from arduino  (WHITE wire)
// comment these two lines if using hardware serial
SoftwareSerial mySerial(2, 3);

Adafruit_Fingerprint finger = Adafruit_Fingerprint(&mySerial);

void setup()  
{
  Serial.begin(9600);
  while (!Serial);  // For Yun/Leo/Micro/Zero/...
  delay(100);
  Serial.println("\n\nAdafruit finger detect test");

  // set the data rate for the sensor serial port
  finger.begin(57600);
  delay(5);
  if (finger.verifyPassword()) {
    Serial.println("Found fingerprint sensor!");
  } else {
    Serial.println("Did not find fingerprint sensor ");
    while (1) { delay(1); }
  }

  finger.getTemplateCount();
  Serial.print("Sensor contains "); Serial.print(finger.templateCount); Serial.println(" templates");
  Serial.println("Waiting for valid finger...");
}

void loop()                     // run over and over again
{
  getFingerprintIDez();
  delay(50);            //don't ned to run this at full speed.
}

uint8_t getFingerprintID() {
  uint8_t p = finger.getImage();
  switch (p) {
    case FINGERPRINT_OK:
      Serial.println("Image taken");
      break;
    case FINGERPRINT_NOFINGER:
      Serial.println("No finger detected");
      return p;
    case FINGERPRINT_PACKETRECIEVEERR:
      Serial.println("Communication error");
      return p;
    case FINGERPRINT_IMAGEFAIL:
      Serial.println("Imaging error");
      return p;
    default:
      Serial.println("Unknown error");
      return p;
  }

  // OK success!

  p = finger.image2Tz();
  switch (p) {
    case FINGERPRINT_OK:
      Serial.println("Image converted");
      break;
    case FINGERPRINT_IMAGEMESS:
      Serial.println("Image too messy");
      return p;
    case FINGERPRINT_PACKETRECIEVEERR:
      Serial.println("Communication error");
      return p;
    case FINGERPRINT_FEATUREFAIL:
      Serial.println("Could not find fingerprint features");
      return p;
    case FINGERPRINT_INVALIDIMAGE:
      Serial.println("Could not find fingerprint features");
      return p;
    default:
      Serial.println("Unknown error");
      return p;
  }
  
  // OK converted!
  p = finger.fingerFastSearch();
  if (p == FINGERPRINT_OK) {
    Serial.println("Found a print match!");
  } else if (p == FINGERPRINT_PACKETRECIEVEERR) {
    Serial.println("Communication error");
    return p;
  } else if (p == FINGERPRINT_NOTFOUND) {
    Serial.println("Did not find a match");
    return p;
  } else {
    Serial.println("Unknown error");
    return p;
  }   
  
  // found a match!
  Serial.print("Found ID #"); Serial.print(finger.fingerID);
  Serial.print(" with confidence of "); Serial.println(finger.confidence);

  return finger.fingerID;
}

// returns -1 if failed, otherwise returns ID #
int getFingerprintIDez() {
  uint8_t p = finger.getImage();
  if (p != FINGERPRINT_OK)  return -1;

  p = finger.image2Tz();
  if (p != FINGERPRINT_OK)  return -1;

  p = finger.fingerFastSearch();
  if (p != FINGERPRINT_OK)  return -1;
  
  // found a match!
  Serial.print("Found ID #"); Serial.print(finger.fingerID);
  Serial.print(" with confidence of "); Serial.println(finger.confidence);
  return finger.fingerID;
}

三、读取指纹库列表

/*
  【Arduino】168种传感器模块系列实验（资料+代码+图形+仿真）
  实验一百五十：AS608光学指纹识别模块 智能锁/考勤门禁开发/指纹采集模块

  实验之四：读取指纹库并列表
  安装库：IDE—工具—管理库—搜索Adafruit-Fingerprint-Sensor-Library—安装
  实验接线：
  Vi      +3.3V（请勿接3.3V以上电源，否则烧毁模块！）
  TX      2
  RX      3
  GND    GND
*/


#include <Adafruit_Fingerprint.h>

int getFingerprintIDez();

// pin #2 is IN from sensor (GREEN wire)
// pin #3 is OUT from arduino  (WHITE wire)
SoftwareSerial mySerial(2, 3);


Adafruit_Fingerprint finger = Adafruit_Fingerprint(&mySerial);

void setup()  
{
  while(!Serial);
  Serial.begin(9600);
  Serial.println("Fingerprint template extractor");

  // set the data rate for the sensor serial port
  finger.begin(57600);

  if (finger.verifyPassword()) {
    Serial.println("Found fingerprint sensor!");
  } else {
    Serial.println("Did not find fingerprint sensor ");
    while (1);
  }

  // Try to get the templates for fingers 1 through 10
  for (int finger = 1; finger < 10; finger++) {
    downloadFingerprintTemplate(finger);
  }
}

uint8_t downloadFingerprintTemplate(uint16_t id)
{
  Serial.println("------------------------------------");
  Serial.print("Attempting to load #"); Serial.println(id);
  uint8_t p = finger.loadModel(id);
  switch (p) {
    case FINGERPRINT_OK:
      Serial.print("Template "); Serial.print(id); Serial.println(" loaded");
      break;
    case FINGERPRINT_PACKETRECIEVEERR:
      Serial.println("Communication error");
      return p;
    default:
      Serial.print("Unknown error "); Serial.println(p);
      return p;
  }

  // OK success!

  Serial.print("Attempting to get #"); Serial.println(id);
  p = finger.getModel();
  switch (p) {
    case FINGERPRINT_OK:
      Serial.print("Template "); Serial.print(id); Serial.println(" transferring:");
      break;
   default:
      Serial.print("Unknown error "); Serial.println(p);
      return p;
  }

  // one data packet is 267 bytes. in one data packet, 11 bytes are 'usesless'
  uint8_t bytesReceived[534]; // 2 data packets
  memset(bytesReceived, 0xff, 534);

  uint32_t starttime = millis();
  int i = 0;
  while (i < 534 && (millis() - starttime) < 20000) {
      if (mySerial.available()) {
          bytesReceived[i++] = mySerial.read();
      }
  }
  Serial.print(i); Serial.println(" bytes read.");
  Serial.println("Decoding packet...");

  uint8_t fingerTemplate[512]; // the real template
  memset(fingerTemplate, 0xff, 512);

  // filtering only the data packets
  int uindx = 9, index = 0;
  while (index < 534) {
      while (index < uindx) ++index;
      uindx += 256;
      while (index < uindx) {
          fingerTemplate[index++] = bytesReceived[index];
      }
      uindx += 2;
      while (index < uindx) ++index;
      uindx = index + 9;
  }
  for (int i = 0; i < 512; ++i) {
      //Serial.print("0x");
      printHex(fingerTemplate, 2);
      //Serial.print(", ");
  }
  Serial.println("\ndone.");

  /*
  uint8_t templateBuffer[256];
  memset(templateBuffer, 0xff, 256);  //zero out template buffer
  int index=0;
  uint32_t starttime = millis();
  while ((index < 256) && ((millis() - starttime) < 1000))
  {
    if (mySerial.available())
    {
      templateBuffer[index] = mySerial.read();
      index++;
    }
  }

  Serial.print(index); Serial.println(" bytes read");

  //dump entire templateBuffer.  This prints out 16 lines of 16 bytes
  for (int count= 0; count < 16; count++)
  {
    for (int i = 0; i < 16; i++)
    {
      Serial.print("0x");
      Serial.print(templateBuffer[count*16+i], HEX);
      Serial.print(", ");
    }
    Serial.println();
  }*/
}



void printHex(int num, int precision) {
    char tmp[16];
    char format[128];

    sprintf(format, "%%.%dX", precision);

    sprintf(tmp, format, num);
    Serial.print(tmp);
}

void loop(){
  
}

四、输入序号，删除指定指纹模板

/*
  【Arduino】168种传感器模块系列实验（资料+代码+图形+仿真）
  实验一百五十：AS608光学指纹识别模块 智能锁/考勤门禁开发/指纹采集模块

  实验之五：输入序号，删除指定指纹模板
  安装库：IDE—工具—管理库—搜索Adafruit-Fingerprint-Sensor-Library—安装
  实验接线：
  Vi      +3.3V（请勿接3.3V以上电源，否则烧毁模块！）
  TX      2
  RX      3
  GND    GND
*/

#include <Adafruit_Fingerprint.h>

// On Leonardo/Micro or others with hardware serial, use those! #0 is green wire, #1 is white
// uncomment this line:
// #define mySerial Serial1

// For UNO and others without hardware serial, we must use software serial...
// pin #2 is IN from sensor (GREEN wire)
// pin #3 is OUT from arduino  (WHITE wire)
// comment these two lines if using hardware serial
SoftwareSerial mySerial(2, 3);

Adafruit_Fingerprint finger = Adafruit_Fingerprint(&mySerial);

void setup()  
{
  Serial.begin(9600);
  while (!Serial);  // For Yun/Leo/Micro/Zero/...
  delay(100);
  Serial.println("\n\nDelete Finger");

  // set the data rate for the sensor serial port
  finger.begin(57600);
  
  if (finger.verifyPassword()) {
    Serial.println("Found fingerprint sensor!");
  } else {
    Serial.println("Did not find fingerprint sensor ");
    while (1);
  }
}


uint8_t readnumber(void) {
  uint8_t num = 0;
  
  while (num == 0) {
    while (! Serial.available());
    num = Serial.parseInt();
  }
  return num;
}

void loop()                     // run over and over again
{
  Serial.println("lease type in the ID # (from 1 to 127) you want to delete...");
  uint8_t id = readnumber();
  if (id == 0) {// ID #0 not allowed, try again!
     return;
  }

  Serial.print("Deleting ID #");
  Serial.println(id);
  
  deleteFingerprint(id);
}

uint8_t deleteFingerprint(uint8_t id) {
  uint8_t p = -1;
  
  p = finger.deleteModel(id);

  if (p == FINGERPRINT_OK) {
    Serial.println("Deleted!");
  } else if (p == FINGERPRINT_PACKETRECIEVEERR) {
    Serial.println("Communication error");
    return p;
  } else if (p == FINGERPRINT_BADLOCATION) {
    Serial.println("Could not delete in that location");
    return p;
  } else if (p == FINGERPRINT_FLASHERR) {
    Serial.println("Error writing to flash");
    return p;
  } else {
    Serial.print("Unknown error: 0x"); Serial.println(p, HEX);
    return p;
  }   
}

五、删除所有指纹模板

/*
  【Arduino】168种传感器模块系列实验（资料+代码+图形+仿真）
  实验一百五十：AS608光学指纹识别模块 智能锁/考勤门禁开发/指纹采集模块

  实验之六：删除所有指纹模板
  安装库：IDE—工具—管理库—搜索Adafruit-Fingerprint-Sensor-Library—安装
  实验接线：
  Vi      +3.3V（请勿接3.3V以上电源，否则烧毁模块！）
  TX      2
  RX      3
  GND    GND
*/

#include <Adafruit_Fingerprint.h>

// On Leonardo/Micro or others with hardware serial, use those! #0 is green wire, #1 is white
// uncomment this line:
// #define mySerial Serial1

// For UNO and others without hardware serial, we must use software serial...
// pin #2 is IN from sensor (GREEN wire)
// pin #3 is OUT from arduino  (WHITE wire)
// comment these two lines if using hardware serial
SoftwareSerial mySerial(2, 3);

Adafruit_Fingerprint finger = Adafruit_Fingerprint(&mySerial);

void setup()  
{
  Serial.begin(9600);
  while (!Serial);  // For Yun/Leo/Micro/Zero/...
  delay(100);

  Serial.println("\n\nDeleting all fingerprint templates!");
  Serial.println("ress 'Y' key to continue");

  while (1) {
    if (Serial.available() && (Serial.read() == 'Y')) {
      break;
    }
  }

  // set the data rate for the sensor serial port
  finger.begin(57600);
  
  if (finger.verifyPassword()) {
    Serial.println("Found fingerprint sensor!");
  } else {
    Serial.println("Did not find fingerprint sensor ");
    while (1);
  }
  
  finger.emptyDatabase();

  Serial.println("Now database is empty ");
}

void loop() {
}

六、OLED显示指纹状态

待更新……

点灯master
关注
  • 0
    点赞
  • 踩
  • 12
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
AS608光学指纹识别指纹采集模块 STM32 51单片机板考勤门禁开发.zip
09-17
AS608光学指纹识别指纹采集模块 STM32 51单片机板考勤门禁开发.zip,大家来下载吧
Adafruit-Fingerprint-Sensor-Library：用于连接Adafruit商店中的指纹传感器的Arduino库
01-30
Adafruit-Fingerprint-Sensor-Library：用于连接Adafruit商店中的指纹传感器的Arduino库
探索Adafruit指纹传感器库：安全与便利的新维度
最新发布
gitblog_00002的博客
04-26 384
探索Adafruit指纹传感器库：安全与便利的新维度 项目地址:https://gitcode.com/adafruit/Adafruit-Fingerprint-Sensor-Library 在数字化时代，生物识别技术正在引领着身份验证和安全防护的新潮流。其中，Adafruit的指纹传感器库提供了一个高效、易于集成的解决方案，将高级别的安全性融入各种DIY项目或商业应用中。 项目简介 Adaf...
ESP32智能门锁
qq_50322135的博客
10-16 1133
ESP32智能门锁
KVG制作-【Arduino指纹解锁 智能家居系列-01】DIY自制的智能门禁，AS608指纹解锁+红外线遥控解锁。附演示视频。
ZYP_KVG的博客
03-03 1万+
**对于上大学的的同学来讲，困扰的问题就是回宿舍发现没钥匙， 指纹解锁的面世，便是其中一种的解决方案。 另外，平时躺在床上玩手机， 我真的懒得下去帮同学开门！ 还有玩游戏玩到一半也总有人来敲门，别担心，我用遥控，成就你的梦想~。**
基于树莓派的寝室门禁系统，指纹识别+Web开门+源代码+文档说明
下载完，不懂运行可以私聊，看到会回
11-28 2147
一、简介基于树莓派3的寝室门禁系统，包括指纹识别开门、web请求开门。开发语言树莓派端：C++网页端：JS系统支持http(s)请求进行开门，因此很容易开发一个APP或者小程序，这里只是简单制作了一个网页端，用浏览器访问就能开门。二、功能与特点开门方式指纹识别开门web请求(http/https，自动进行内网穿透，通过公网服务器/域名访问)通知（开门后每个寝室成员会收到通知）微信实时通知系统每天23:23自动关机，第二天6:30自动启动。
arduino电子指纹锁，AS608/FPM10A互通
01-06
之前有篇文章只有图，所以今天来稍微详细说说这个制作过程。 这也是学校的什么鬼项目，一直不知道该做什么东西，后来在网上看到有大学生给自己宿舍装了指纹锁，一下子受到启发，我自己也搞一个！ 材料，arduino UNO 开发板；光学指纹模块，型号AS608/FPM10A；舵机或者电磁锁； 自己做的时候也看了不少材料，电容式那种指纹模块比较便宜，比如手机上的小圆片就是，我感觉打卡机那种光学的精度比较好，可存的指纹数量多，看起来也比较“高大上”。 至于源码，这里的源码指的仅仅是指纹模块的源码，GitHub上有，非常好用，下载下来解压，包放在arduino的libraries文件夹里，打开arduino，
Arduino--AS608指纹传感器
热门推荐
u011816009的博客
06-10 1万+
（1）简介 如图所示为AS608指纹传感器，其可支持串口和USB通信 模块芯片上的管脚如下： 序号 名称 说明 1 Vi 模块电源正输入端 2 Tx 串行数据输出 3 Rx 串行数据输入 4 GND 信号地 5 WAK 感应信号输出，默认高电平有效 6 Vt 触摸感应电源输入，3.3V供电 7 U+ USB D+ 8 U- USB D- （2）调试 本文基于串口开发（使用UNO中软件模拟串口（2,3），节约串口资源），其接口如下： AS608 UN
智能锁方案——stm32作为主控，AS608光学模块实现指纹识别功能
m0_71718440的博客
06-05 746
智能锁方案——stm32作为主控，AS608光学模块实现指纹识别功能，HMI智能串口屏实现UI界面显示以及触控，外加A9G模块实现开锁后短信通知以及手机远程短消息密码开锁，可另外加RC522IC卡识别功能 ID:69320628724191050...
毕业设计 单片机指纹识别门禁系统设计与实现 - 物联网 嵌入式
MDC_sir的博客
12-29 1168
Hi，大家好，学长今天向大家介绍一个学长做的单片机项目基于单片机的指纹识别门禁系统设计大家可用于 课程设计 或 毕业设计。
AS608指纹模块——其实从初学Arduino到做出指纹锁只需要一周
Jerryxuzherui的博客
12-15 2179
该文章介绍了如何做一个适合Arduino初学者的指纹锁，该指纹锁的功能简单，包括指纹特征的储存、指纹识别开锁、以及在OLED屏上显示当前的温湿度情况等。
AS608光学指纹模块Arduino案例.rar
04-21
ATK-AS608 指纹识别模块是 ALIENTEK 推出的一款高性能的光学指纹识别模块。压缩包中包含AS608数据手册，AS608用户手册，Arduino指纹模块例程代码，串口调试助手，AS608模块上位机及上位机操作视频等
基于ARM的光学指纹识别系统的设计方案
01-19
摘 要：本文介绍了一种基于ARM的光学指纹识别系统的设计方案。本方案采用ARM处理器作为控制，构建指纹识别算法的嵌入式系统的设计方法及过程。该系统采用光学指纹传感器（内建格科微电子有限公司的光学GC0307 CMOS图像采集芯片）与ARM Cortex M3内核的意法半导体公司32位高性能单片机STM32F205RE组成功能主体，采用Sobel边缘检测算子、Gabor滤波、图像二值化等图像采集与处理算法对指纹图像进行识别。经过反复实践证明，该方案适合嵌入式组件开发中需要进行生物指纹特征提取、识别，指纹身份、比对等场合。系统具有高性价比且交互简易、识别率高、扩展性强，便于嵌入式应用。 　　0
as 608 Arduino综合测试板原理图
12-06
10、Arduino综合板原理图10、Arduino综合板原理图
AS608指纹模块和ESP8266wifi模块在STM32f103上的应用
09-30
AS608指纹模块和ESP8266wifi模块在STM32f103上的应用，
as608指纹模块的最简单的使用,作为学习使用,可以制作密码锁
03-30
as608指纹模块的最简单的使用,作为学习使用,可以制作密码锁,使用正点原子 探索者stm32f407作为芯片,直接拿来就能用
STM32C8T6-AS608指纹识别
03-07
STM32C8T6_AS608指纹识别,AS608 指纹识别模块主要是指采用了杭州晟元芯片技术有限公司(Synochip)的 AS608 指纹识别芯片 而做成的指纹模块，模块厂商只是基于该芯片设计外围电路，集成一个可供2次开发的指纹模块；...
AS608光学指纹识别模块资料.zip
05-15
AS608光学指纹识别模块资料.zip
【】AS608光学指纹识别指纹采集模块.rar
06-22
可用于stm32.51系列单片机，内有配套程序，可直接用在51单片机或者stm32，已经使用过。内配有上位机，上位机可对模块内部存储指纹进行操作，操作简单实用。
用C语言生成一份AS608光学指纹识别模块控制程序模板
03-28
#include <stdio.h> #include <stdlib.h> #include "AS608.h" int main() { int r; unsigned char buf[1024]; unsigned int addr; unsigned int size; unsigned char data; unsigned int id; unsigned int score; // 初始化指纹识别模块 r = AS608_Init(); if (r != AS608_OK) { printf("Failed to initialize AS608 module: %d\n", r); return 1; } // 设置指纹识别模块的参数 r = AS608_SetParam(PARAM_SECURITY_LEVEL, 5); if (r != AS608_OK) { printf("Failed to set AS608 parameter: %d\n", r); return 1; } // 注册指纹 printf("Please put your finger on the sensor...\n"); r = AS608_Register(); if (r != AS608_OK) { printf("Failed to register finger: %d\n", r); return 1; } printf("Finger registered successfully!\n"); // 识别指纹 printf("Please put your finger on the sensor...\n"); r = AS608_Identify(&id, &score); if (r != AS608_OK) { printf("Failed to identify finger: %d\n", r); return 1; } printf("Finger identified as ID %d with score %d\n", id, score); // 读取指纹模板 addr = 0; size = 512; r = AS608_ReadTemplate(addr, size, buf); if (r != AS608_OK) { printf("Failed to read template: %d\n", r); return 1; } printf("Template read successfully!\n"); // 写入指纹模板 addr = 0; size = 512; r = AS608_WriteTemplate(addr, size, buf); if (r != AS608_OK) { printf("Failed to write template: %d\n", r); return 1; } printf("Template written successfully!\n"); // 删除指纹模板 id = 1; r = AS608_DeleteTemplate(id); if (r != AS608_OK) { printf("Failed to delete template: %d\n", r); return 1; } printf("Template deleted successfully!\n"); // 清空指纹模板库 r = AS608_ClearTemplate(); if (r != AS608_OK) { printf("Failed to clear template: %d\n", r); return 1; } printf("Template cleared successfully!\n"); // 关闭指纹识别模块 r = AS608_Close(); if (r != AS608_OK) { printf("Failed to close AS608 module: %d\n", r); return 1; } return 0; }

“相关推荐”对你有帮助么？

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值