ARM 10.12

最新推荐文章于 2024-07-04 15:00:14 发布

草原小肥羊\n

最新推荐文章于 2024-07-04 15:00:14 发布

阅读量538

点赞数

文章标签： arm开发算法

本文链接：https://blog.csdn.net/weixin_58469613/article/details/133799085

版权

设置按键中断，按键1按下，LED亮，再按一次，灭

按键2按下，蜂鸣器响。再按一次，不响

按键3按下，风扇转，再按一次，风扇停

src/key.c

#include"key.h"

//按键3的配置
void key3_config()
{
    //RCC使能GPIOF时钟
    RCC->MP_AHB4ENSETR |= (0x1<<5);
    //设置PF8 GPIO输入
    GPIOF->MODER &= (~(0x3<<16));
    //设置PF8产生EXTI事件 EXTI_EXTICRx
    EXTI->EXTICR3 &=(~(0xFF<<0));
    EXTI->EXTICR3 |= (0x5<<0);
    //设置事件触发方式为下降沿触发EXTI_FTSR1
    EXTI->FTSR1 |= (0x1<<8);
    //设置EXTI事件触发不屏蔽EXTI_IMR1
    EXTI->C1IMR1 |= (0x1<<8);
    //使能中断能转发到特定的CPU接口层GICD_ISENABLERx
    GICD->ISENABLER[3] |= (0X1<<2); 
    // GICD_ISENABLERx设置中断优先级
    GICD->IPRIORITYR[24] &= (~(0X1F<<19)); 
    //设置当前中断被转发到哪一个CPU处理GICD_ITARGETSRx
    GICD->ITARGETSR[24]  &= (~(0X3<<16));
    GICD->ITARGETSR[24] |= (0X1<<16);
    //设置中断优先级掩码GICC_PMR
    GICC->PMR |= (0x1F<<3);
    //使能CPU可以处理组0转发的中断GICC_CTLR
    GICC->CTRL |= 0X1;
}
//按键1 按键2以及GICC层的配置
void key_config()
{
    //RCC使能GPIOF时钟
    RCC->MP_AHB4ENSETR |= (0x1<<5);
    //设置PF9 PF7GPIO输入
    //PF9
    GPIOF->MODER &= (~(0x3<<18));
    //pf7
    GPIOF->MODER &= (~(0x3<<14));
    //设置PF9 PF7 产生EXTI事件 EXTI_EXTICRx
    //pf7
    EXTI->EXTICR2 &=(~(0xFF<<24));
    EXTI->EXTICR2 |= (0x5<<24);
    //pf9
    EXTI->EXTICR3 &=(~(0xFF<<8));
    EXTI->EXTICR3 |= (0x5<<8);
    //设置事件触发方式为下降沿触发EXTI_FTSR1
    //pf7
    EXTI->FTSR1 |= (0x1<<7);
    //pf9
    EXTI->FTSR1 |= (0x1<<9);
    //设置EXTI事件触发不屏蔽EXTI_IMR1
    //PF7
    EXTI->C1IMR1 |= (0x1<<7);
    //PF9
    EXTI->C1IMR1 |= (0x1<<9);
    //使能中断能转发到特定的CPU接口层GICD_ISENABLERx
    //PF7 97号中断
    GICD->ISENABLER[3] |= (0X1<<1); 
    //PF9 99号中断
    GICD->ISENABLER[3] |= (0X1<<3); 
    // GICD_ISENABLERx设置中断优先级
    //PF7
    GICD->IPRIORITYR[24] &= (~(0X1F<<11)); 
    //PF9
    GICD->IPRIORITYR[24] &= (~(0X1F<<27)); 
    //设置当前中断被转发到哪一个CPU处理GICD_ITARGETSRx
    //pf7 97中断
    GICD->ITARGETSR[24]  &= (~(0X3<<8));
    GICD->ITARGETSR[24] |= (0X1<<8);
    //pf9 99中断
    GICD->ITARGETSR[24]  &= (~(0X3<<24));
    GICD->ITARGETSR[24] |= (0X1<<24);
    //使能组0转发中断GICD_CTLR
    GICD->CTRL |= 0X1;
    //设置中断优先级掩码GICC_PMR
    GICC->PMR |= (0x1F<<3);
    //使能CPU可以处理组0转发的中断GICC_CTLR
    GICC->CTRL |= 0X1;

}
//延时
void delay(int ms)
{
	int i,j;
	for(i = 0;i < ms;i++)
	{
		for(j = 0;j < 2000;j++);
	}
}
//给RCC使能
void rcc_start()
{
	RCC->MP_AHB4LPENSETR |= (0x3<<4);
}
//GPIO初始化
void gpio_start()
{
	//PE10 PE9 PE8设置为输出模式
	GPIOE->MODER &= (~(0x3f<<16));
	GPIOE->MODER |= (0x15<<16);
	//PF10设置为输出模式
	GPIOF->MODER &= (~(0x3<<20));
	GPIOF->MODER |= (0x1<<20);
	//PB6设置为输出模式
	GPIOB->MODER &= (~(0x3<<12));
	GPIOB->MODER |= (0x1<<12);
	//PE10 PE9 PE8设置为推挽输出
	GPIOE->OTYPER &= (~(0x7<<8));
	//PF10设置为推挽输出
	GPIOF->OTYPER &= (~(0x1<<10));
	//PB6设置为推挽输出
	GPIOB->OTYPER &= (~(0x1<<6));
	//PE10 PE9 PE8设置为低速输出
	GPIOE->OSPEEDR &= (~(0x3f<<16));
	//PF10设置为低速输出
	GPIOF->OSPEEDR &= (~(0x3<<20));
	//PB6设置为低速输出
	GPIOB->OSPEEDR &= (~(0x3<<12));
	//PE10 PE9 PE8设置为无上拉下拉电阻
	GPIOE->PUPDR &= (~(0x3f<<16));
	//PF10设置为无上拉下拉电阻
	GPIOF->PUPDR &= (~(0x3<<20));
	//PB6设置为无上拉下拉电阻
	GPIOB->PUPDR &= (~(0x3<<16));
}

src/do_irq.c

#include "key.h"
extern void printf(const char *fmt, ...);
unsigned int i = 0;
unsigned int num1 = 0, num2 = 0,num3 = 0; //用于记录按键按下次数
void do_irq(void) 
{
    int irqno;//保存中断号
    irqno=GICC->IAR & 0X3FF;
    switch(irqno)
    {
        case 99://key1
            //按键1中断处理
            printf("KEY1 INT\n");
            //灯亮
            if(num1 == 0)
            {
                //PF10
                GPIOF->ODR |= (0x1<<10);
                //PE10 PE8
                GPIOE->ODR |= (0x5<<8);
                num1++;
            }
            //灯灭
            else if(num1 > 0)
            {
                //PF10
                GPIOF->ODR &= ~(0x1<<10);
                //PE10 PE8
                GPIOE->ODR &= ~(0x5<<8);
                num1 = 0;
            }
            //清除挂起中断标志位GICD_ICPENDRx
            GICD->ICPENDR[3] |= (0x1<<3);
            //清除中断触发标志位EXTI_FPR1
            EXTI->FPR1 |= (0x1<<9);
            break;
        case 97://key2
            //按键2中断处理
            printf("KEY2 INT\n");
            //蜂鸣器转
            if(num2 == 0)
            {
                //PB6
                GPIOB->ODR |= (0x1<<6);
                num2++;
            }
            //蜂鸣器停
            else if(num2 > 0)
            {
                //PB6
                GPIOB->ODR &= ~(0x1<<6);
                num2 = 0;
            }
            //清除挂起中断标志位GICD_ICPENDRx
            GICD->ICPENDR[3] |= (0x1<<1);
            //清除中断触发标志位EXTI_FPR1
            EXTI->FPR1 |= (0x1<<7);
            break;
        case 98://key3
            //按键3中断处理
            printf("KEY3 INT\n");
            //风扇转
            if(num3 == 0)
            {
                //PE9
                GPIOE->ODR |= (0x1<<9);
                num3++;
            }
            //风扇停
            else if(num3 > 0)
            {
                //PE9
                GPIOE->ODR &= ~(0x1<<9);
                num3 = 0;
            }
            //清除挂起中断标志位GICD_ICPENDRx
            GICD->ICPENDR[3] |= (0x1<<2);
            //清除中断触发标志位EXTI_FPR1
            EXTI->FPR1 |= (0x1<<8);
            break;
    }
    //清除处理完的中断号GICC_EOIR
    GICC->EOIR =irqno;
}

include/key.h

#ifndef __KEY_H__
#define __KEY_H__
#include "../common/include/stm32mp1xx_exti.h"
#include "../common/include/stm32mp1xx_gpio.h"
#include "../common/include/stm32mp1xx_rcc.h"
#include "../common/include/stm32mp1xx_gic.h"
void key_config();
void key3_config();
//延时
void delay(int ms);
//给RCC使能
void rcc_start();
//GPIO初始化
void gpio_start();

#endif

main.c

#include "key.h"

int main()
{
    //中断初始化
    key_config();
	key3_config();
	//GPIO串口初始化
	gpio_start();
    while(1)
    {
        //保证主程序不结束
    }
    return 0;
}