IPV6拓扑实验

 要求：
1.全网可达
2.isp只能配置ip地址

一、配置ipv4地址

先使ipv4能够访问运营商

在r2上配置nat

[r2]acl 2000
[r2-acl-basic-2000]rule permit source any 
[r2]int g0/0/2
[r2-GigabitEthernet0/0/2]nat outbound 2000

二、划分6to4 tunnel地址

 将r2g0/0/2接口ipv4地址转换为6to4 tunnel地址2002:1d01:0102::/48划分给下方的路由器

配置ipv6地址（）

[r1]ipv6 
[r1]interface g0/0/0
[r1-GigabitEthernet0/0/0]ipv6 enable 
[r1-GigabitEthernet0/0/0]ipv6 address 2002:1d01:0102:1::1 64
[r1-GigabitEthernet0/0/0]int l0
[r1-LoopBack0]ipv6 enable 
[r1-LoopBack0]ipv6 address 2002:1d01:0102:11::1 64
[r1-LoopBack0]display ipv6 interface brief 
*down: administratively down
(l): loopback
(s): spoofing
Interface                    Physical              Protocol   
GigabitEthernet0/0/0         up                    up         
[IPv6 Address] 2002:1D01:102:1::1
LoopBack0                    up                    up(s)      
[IPv6 Address] 2002:1D01:102:11::1
[r1-LoopBack0]

三、配置ripng

[r10]ripng 1
[r10-ripng-1]int g0/0/1
[r10-GigabitEthernet0/0/1]ripng 1 enable 
[r10-GigabitEthernet0/0/1]q
[r10]int l0
[r10-LoopBack0]ripng 1 enable 
[r10-LoopBack0]q
[r10]interfa Tunnel 0/0/0
[r10-Tunnel0/0/0]ripng 1 enable 
[r10-Tunnel0/0/0]q

四、配置6to4 tunnel隧道 

在r2-r10上配置隧道

[r2-Tunnel0/0/0]display this 
[V200R003C00]
#
interface Tunnel0/0/0
 ipv6 enable 
 ipv6 address 2002:1D01:102:3::2/64 
 tunnel-protocol ipv6-ipv4 6to4
 source GigabitEthernet0/0/2
#
return
[r2-Tunnel0/0/0]

r1ping r11

  

五、启用ospfv3

在ospf区域启用ospfv3 100，例r6

[r6]ospfv3 100
[r6-ospfv3-100]router-id 6.6.6.6
[r6]int g0/0/0
[r6-GigabitEthernet0/0/0]ospfv3 100 area 0
[r6-GigabitEthernet0/0/1]int l0
[r6-LoopBack0]ospfv3 100 area 0

 六、配置bgp

[r3]bgp 64511
[r3-bgp]router-id 3.3.3.3
[r3-bgp]confederation id 100
[r3-bgp]peer 4::4 as-number 64511
[r3-bgp]peer 4::4 connect-interface l0
[r3-bgp]ipv6-family 
[r3-bgp-af-ipv6]peer 4::4 enable 
[r3-bgp-af-ipv6]peer 4::4 next-hop-local 

[r5-bgp]display this 
[V200R003C00]
#
bgp 64511
 router-id 5.5.5.5
 confederation id 100
 confederation peer-as 64512
 peer 4::4 as-number 64511 
 peer 4::4 connect-interface LoopBack0
 peer 6::6 as-number 64512 
 peer 6::6 ebgp-max-hop 2 
 peer 6::6 connect-interface LoopBack0
 #
 ipv4-family unicast
  undo synchronization
 #
 ipv6-family unicast
  undo synchronization
  peer 4::4 enable
  peer 6::6 enable
#
return

 七、bgp导入路由

在r7上导入ripng 2

[r7-bgp-af-ipv6]import-route ripng 2

在r6上导入ospfv3 100 

[r6-bgp-af-ipv6]import-route ospfv3 100

  

八、配置缺省

在r3的ospfv3 100 中下放缺省指向r2， r7、r8下放缺省指向r6

九、测试