hcip实验

实验要求
1、AS1存在两个环回接口，一个地址为192.168.1.0/24该地址不能在任何协议中宣告。AS3存在两个环回接口，一个地址为192.168.2.0/24该地址不能在任何协议中宣告，最终要求这两个环回接口可以互相通讯。AS1的另一个环回接口为10.0.0.0/24，AS3的另一个环回接口为11.0.0.0/24

2、整个AS2的IP地址为172.16.0.0/16，请合理划分。

3、AS之间的骨干链路IP地址随意定制。

4、使用BGP协议让整个网络所有设备的环回接口可以互相访问。

5、减少路由条目数量，避免环路出现。

实验内容及步骤
1、对整个AS2的IP地址进行子网划分
        将172.16.0.0/16的网段划分为172.16.0.0/24的多个网段，因为在实际工程当中，24的网段更符合用户网段，因此先将网段划分为172.16.0.0 /24的多个子网掩码为24的网段，再将172.16.0.0/24的多个网段进行划分，将172.16.0.0/24的网段用于P2P网络当中，将172.16.1.0/24的网段用于MA网络当中，每个路由器的环回接口都使用一个子网掩码为24的网段。

2、对所有设备进行IP地址的配置
R1

[r1]int g 0/0/0
[r1-GigabitEthernet0/0/0]ip a 12.0.0.1 24
[r1-GigabitEthernet0/0/0]int lo0
[r1-LoopBack0]ip a 192.168.1.1 24
[r1-LoopBack0]int lo1
[r1-LoopBack1]ip a 10.0.0.1 24

R2

[r2]int g0/0/0
[r2-GigabitEthernet0/0/0]ip a 12.0.0.2 24
[r2-GigabitEthernet0/0/0]int lo0
[r2-LoopBack0]ip a 172.16.2.1 24
[r2]int g 0/0/1
[r2-GigabitEthernet0/0/1]ip a 172.16.1.1 29
[r2-GigabitEthernet0/0/1]int g0/0/2
[r2-GigabitEthernet0/0/2]ip a 172.16.1.9 29

R3

[r3]int g0/0/0
[r3-GigabitEthernet0/0/0]ip a 172.16.1.2 29
[r3-GigabitEthernet0/0/0]int lo0
[r3-LoopBack0]ip a 172.16.3.1 24
[r3-LoopBack0]int g 0/0/1
[r3-GigabitEthernet0/0/1]ip a 172.16.1.17 29

R4

[r4]int g0/0/0
[r4-GigabitEthernet0/0/0]ip a 172.16.1.18 29
[r4-GigabitEthernet0/0/0]int g 0/0/1
[r4-GigabitEthernet0/0/1]ip a 172.16.1.25 29
[r4-GigabitEthernet0/0/1]int lo0
[r4-LoopBack0]ip a 172.16.4.1 24

R5

[r5]int g 0/0/0
[r5-GigabitEthernet0/0/0]ip a 172.16.1.10 29
[r5-GigabitEthernet0/0/0]int g 0/0/1
[r5-GigabitEthernet0/0/1]ip a 172.16.1.133 29
[r5-GigabitEthernet0/0/1]int lo0
[r5-LoopBack0]ip a 172.16.5.1 24

R6

[r6]int g 0/0/0
[r6-GigabitEthernet0/0/0]ip a 172.16.1.34 29
[r6-GigabitEthernet0/0/0]int lo0
[r6-LoopBack0]ip a 172.16.6.1 24
[r6-LoopBack0]int g0/0/1
[r6-GigabitEthernet0/0/1]ip a 172.16.1.41 29

R7

[r7]int g0/0/0
[r7-GigabitEthernet0/0/0]ip a 172.16.1.42 29
[r7-GigabitEthernet0/0/0]int lo0
[r7-LoopBack0]ip a 172.16.7.1 24
[r7-LoopBack0]int g 0/0/1
[r7-GigabitEthernet0/0/1]ip a 172.16.1.26 29
[r7-GigabitEthernet0/0/1]int g 0/0/2
[r7-GigabitEthernet0/0/2]ip a 78.0.0.1 24

R8

[r8]int g 0/0/0
[r8-GigabitEthernet0/0/0]ip a 78.0.0.2 24
[r8-GigabitEthernet0/0/0]int lo0
[r8-LoopBack0]ip a 192.168.2.1 24
[r8-LoopBack0]int lo1
[r8-LoopBack1]ip a 11.0.0.1 24

3、在AS2中启用OSPF协议
R2 

[r2]ospf 1 router-id 2.2.2.2
[r2-ospf-1]a 0
[r2-ospf-1-area-0.0.0.0]network 172.16.0.0 0.0.255.255

R3

[r3]ospf 1 router-id 3.3.3.3
[r3-ospf-1]a 0
[r3-ospf-1-area-0.0.0.0]network 172.16.0.0 0.0.255.255

R4

[r4]ospf 1 router-id 4.4.4.4
[r4-ospf-1]a 0
[r4-ospf-1-area-0.0.0.0]network 172.16.0.0 0.0.255.255

R5

[r5]ospf 1 router-id 5.5.5.5
[r5-ospf-1]a 0
[r5-ospf-1-area-0.0.0.0]network 172.16.0.0 0.0.255.255

R6

[r6]ospf 1 router-id 6.6.6.6
[r6-ospf-1]a 0
[r6-ospf-1-area-0.0.0.0]network 172.16.0.0 0.0.255.255

R7

[r7]ospf 1 router-id 7.7.7.7
[r7-ospf-1]a 0
[r7-ospf-1-area-0.0.0.0]network 172.16.0.0 0.0.255.255

4、对所有设备启用BGP协议，并进行对等体的建立
R1

[r1]bgp 1 
[r1-bgp]route-select
[r1-bgp]router-id 1.1.1.1  
[r1-bgp]peer 12.0.0.2 as 2

R2

[r2]bgp 64512  
[r2-bgp]route-select
[r2-bgp]router-id 2.2.2.2  
[r2-bgp]confederation id 2   
[r2-bgp]confederation peer-as 64513
[r2-bgp]peer 12.0.0.1 as 1  
[r2-bgp]peer 172.16.3.1 as 64512   
[r2-bgp]peer 172.16.3.1 connect-interface LoopBack 0   
[r2-bgp]peer 172.16.5.1 as 64513  
[r2-bgp]peer 172.16.5.1 connect-interface LoopBack 0
[r2-bgp]peer 172.16.5.1 ebgp-max-hop 2  
[r2-bgp]peer 172.16.3.1 next-hop-local
[r2-bgp]peer 172.16.5.1 next-hop-local

R3

[r3]bgp 64512
[r3-bgp]router-id 3.3.3.3 
[r3-bgp]confederation id 2
[r3-bgp]peer 172.16.2.1 as 64512  
[r3-bgp]peer 172.16.2.1 connect-interface LoopBack 0 
[r3-bgp]peer 172.16.4.1 as 64512 
[r3-bgp]peer 172.16.4.1 connect-interface LoopBack 0

R4

[r4]bgp 64512
[r4-bgp]router-id 4.4.4.4 
[r4-bgp]confederation id 2
[r4-bgp]confederation peer-as 64513
[r4-bgp]peer 172.16.3.1 as 64512
[r4-bgp]peer 172.16.3.1 connect-interface LoopBack 0
[r4-bgp]peer 172.16.7.1 as 64513
[r4-bgp]peer 172.16.7.1 connect-interface LoopBack 0
[r4-bgp]peer 172.16.7.1 ebgp-max-hop 2

R5

[r5]bgp 64513
[r5-bgp]router-id 5.5.5.5  
[r5-bgp]confederation id 2
[r5-bgp]confederation peer-as 64512
[r5-bgp]peer 172.16.2.1 as 64512
[r5-bgp]peer 172.16.2.1 connect-interface LoopBack 0
[r5-bgp]peer 172.16.2.1 ebgp-max-hop 2
[r5-bgp]peer 172.16.6.1 as 64513
[r5-bgp]peer 172.16.6.1 connect-interface LoopBack 0

R6

[r6]bgp 64513
[r6-bgp]router-id 6.6.6.6   
[r6-bgp]confederation id 2
[r6-bgp]peer 172.16.5.1 as 64513  
[r6-bgp]peer 172.16.5.1 connect-interface LoopBack 0
[r6-bgp]peer 172.16.7.1 as 64513
[r6-bgp]peer 172.16.7.1 connect-interface LoopBack 0

R7

[r7]bgp 64513
[r7-bgp]router-id 7.7.7.7   
[r7-bgp]confederation id 2
[r7-bgp]confederation peer-as 64512 
[r7-bgp]peer 172.16.6.1 as 64513
[r7-bgp]peer 172.16.6.1 connect-interface LoopBack 0  
[r7-bgp]peer 172.16.4.1 as 64512 
[r7-bgp]peer 172.16.4.1 connect-interface LoopBack 0
[r7-bgp]peer 172.16.4.1 ebgp-max-hop 2
[r7-bgp]peer 78.0.0.2 as 3
[r7-bgp]peer 172.16.4.1 next-hop-local
[r7-bgp]peer 172.16.6.1 next-hop-local

R8

[r8]bgp 3   
[r8-bgp]router-id 8.8.8.8    
[r8-bgp]peer 78.0.0.1 as 2

5、发布路由信息
R1

[r1]bgp 1
[r1-bgp]network 10.0.0.0 24

R8

[r8]bgp 3
[r8-bgp]network 11.0.0.0 24

6、破除IBGP之间的水平分割，配置路由反射器
R3

[r3]bgp 64512    
[r3-bgp]peer 172.16.2.1 reflect-client 

R6

[r6]bgp 64513
[r6-bgp]peer 172.16.7.1 reflect-client

7、做空接口、汇总以及宣告
R2

[r2]ip route-static 172.16.0.0 21 NULL 0   
[r2]bgp 64512 
[r2-bgp]network 172.16.0.0 21

R7

[r7]ip route-static 172.16.0.0 22 NULL 0 
[r7]bgp 64513
[r7-bgp]network 172.16.0.0 21

8、建立GRE隧道，来实现两个环回的通化讯
R1

[r1]int t0/0/0
[r1-Tunnel0/0/0]ip a 192.168.10.1 24  
[r1-Tunnel0/0/0]tunnel-protocol gre  
[r1-Tunnel0/0/0]source 10.0.0.1
[r1-Tunnel0/0/0]destination 11.0.0.1  
[r1]ip route-static 192.168.1.0 24 99.0.0.2

R8

[r8]int t0/0/0
[r8-Tunnel0/0/0]ip a 192.168.10.2 24 
[r8-Tunnel0/0/0]tunnel-protocol gre  
[r8-Tunnel0/0/0]source 11.0.0.1
[r8-Tunnel0/0/0]destination 10.0.0.1
[r8]ip route-static 192.168.2.0 24 99.0.0.1

实验结果及验证 
1、IP地址的查看

R1

R8

2、BGP路由查看

R1R8

3、所有设备互相访问

R1pingR5

 R8pingR3R1pingR8

4、R1与R8未宣告的环回接口之间的通讯