检查是否安装了ntp相关包。如果没有安装ntp相关包,使用rpm或yum安装,安装也非常简单方便。
[root@localhost ~]# rpm -qa | grep ntp
ntpdate-4.2.6p5-1.el6.x86_64
fontpackages-filesystem-1.41-1.1.el6.noarch
1.各个选项信息:
#系统时间与BIOS事件的偏差记录
driftfile /etc/ntp/drift
restrict 控制相关权限。
语法为: restrict IP地址 mask 子网掩码 参数
其中IP地址也可以是default ,default 就是指所有的IP
参数有以下几个:
ignore :关闭所有的 NTP 联机服务
nomodify:客户端不能更改服务端的时间参数,但是客户端可以通过服务端进行网络校时。
notrust :客户端除非通过认证,否则该客户端来源将被视为不信任子网
noquery :不提供客户端的时间查询:用户端不能使用ntpq,ntpc等命令来查询ntp服务器
notrap :不提供trap远端登陆:拒绝为匹配的主机提供模式 6 控制消息陷阱服务。陷阱服务是 ntpdq 控制消息协议的子系统,用于远程事件日志记录程序。
nopeer :用于阻止主机尝试与服务器对等,并允许欺诈性服务器控制时钟
kod : 访问违规时发送 KoD 包。
restrict 192.168.0.0 mask 255.255.255.0 notrust nomodify notrap
在上例中,掩码地址扩展为255,因此从192.168.0.1-192.168.0.254的服务器都可以使用我们的NTP服务器来同步时间
#此时表示限制向从192.168.0.1-192.168.0.254这些IP段的服务器提供NTP服务。
restrict 192.168.0.0 mask 255.255.255.0 notrust nomodify notrap noquery
#设置默认策略为允许任何主机进行时间同步
restrict 127.0.0.1
修改/etc/ntp/stpe-tickers文件,内容如下(当ntpd服务启动时,会自动与该文件中记录的上层NTP服务进行时间校对)
[root@localhost ntp]# more /etc/ntp/step-tickers
# List of servers used for initial synchronization.
[root@localhost ntp]# vi /etc/ntp/step-tickers
# List of servers used for initial synchronization.
server 192.168.7.49 prefer
server 0.rhel.pool.ntp.org
server 1.rhel.pool.ntp.org
server 2.rhel.pool.ntp.org
server 3.rhel.pool.ntp.org
关于ntp.conf and step-tickers区别:
ntp服务,默认只会同步系统时间。如果想要让ntp同时同步硬件时间,可以设置/etc/sysconfig/ntpd文件,在/etc/sysconfig/ntpd文件中,添加 SYNC_HWCLOCK=yes 这样,就可以让硬件时间与系统时间一起同步。
#允许BIOS与系统时间同步,也可以通过hwclock -w 命令
SYNC_HWCLOCK=yes
7.IPTABLES 配置
由于NTP服务需要使用到UDP端口号123,所以当系统的防火墙(Iptables)启动的情况下,必须开放UDP端口号123。
[root@localhost ~]# /etc/init.d/iptables status
Table: filter
Chain INPUT (policy ACCEPT)
num target prot opt source destination
1 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED
2 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0
3 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0
4 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22
5 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited
Chain FORWARD (policy ACCEPT)
num target prot opt source destination
1 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited
Chain OUTPUT (policy ACCEPT)
num target prot opt source destination
[root@localhost ~]# /sbin/iptables -I INPUT -p udp --dport 123 -j ACCEPT
[root@localhost ~]# /etc/init.d/iptables status
Table: filter
Chain INPUT (policy ACCEPT)
num target prot opt source destination
1 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:123
2 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED
3 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0
4 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0
5 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22
6 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited
Chain FORWARD (policy ACCEPT)
num target prot opt source destination
1 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited
Chain OUTPUT (policy ACCEPT)
num target prot opt source destination
[root@localhost ~]#
[root@localhost ~]# /usr/sbin/ntpq -c rv | grep stratum
stratum=16, precision=-24, rootdelay=0.000, rootdisp=3.525, refid=INIT,
[root@localhost~]#
[root@localhost ~]# service ntpd status
ntpd is stopped
[root@localhost ~]# service ntpd start
Starting ntpd: [ OK ]
[root@localhost ~]#
service ntpd status #查看ntpd服务状态
service ntpd start #启动ntpd服务
service ntpd stop #停止ntpd服务
service ntpd restart #重启ntpd服务
检查ntp服务是否开机启动,将其设置为开机启动。
[root@localhost ~]# chkconfig --list ntpd
ntpd 0:off 1:off 2:off 3:off 4:off 5:off 6:off
[root@localhost ~]# runlevel
N 3
[root@localhost ~]# chkconfig ntpd on #在运行级别2、3、4、5上设置为自动运行
[root@localhost ~]# chkconfig --list ntpd
ntpd 0:off 1:off 2:on 3:on 4:on 5:on 6:off
[root@localhost ~]#
如果要设置在运行级别上自动运行,可以使用下面命令
chkconfig --level 345 ntpd on
可以用下面命令检测NTP服务是否运行
[root@localhost ~]# pgrep ntpd
2639
2641
[root@localhost ~]# netstat -tlunp | grep ntp #如果看到123端口,说明ntp服务成功启动。
udp 0 0 192.168.7.224:123 0.0.0.0:* 2639/ntpd
udp 0 0 127.0.0.1:123 0.0.0.0:* 2639/ntpd
udp 0 0 0.0.0.0:123 0.0.0.0:* 2639/ntpd
udp 0 0 fe80::250:56ff:feb3:b5:123 :::* 2639/ntpd
udp 0 0 ::1:123 :::* 2639/ntpd
udp 0 0 :::123 :::* 2639/ntpd
[root@localhost ~]#
查看ntp服务器有无和上层ntp连通
[root@localhost ~]# ntpstat
synchronised to NTP server (192.168.7.49) at stratum 6
time correct to within 440 ms
polling server every 128 s
[root@localhost ~]#
查看ntp服务器与上层ntp的状态
[root@localhost ~]# ntpq -p
remote refid st t when poll reach delay offset jitter
==============================================================================
192.168.7.49 192.168.7.50 5 u 13 64 3 5.853 1137178 2.696
[root@localhost ~]# ntpq -p
remote refid st t when poll reach delay offset jitter
==============================================================================
192.168.7.49 192.168.7.50 5 u 17 64 3 5.853 1137178 2.696
[root@localhost ~]# ntpq -p
remote refid st t when poll reach delay offset jitter
==============================================================================
192.168.7.49 192.168.7.50 5 u 1 64 1 0.937 -9.570 0.000
remote - 本机和上层ntp的ip或主机名,“+”表示优先,“*”表示次优先
refid - 参考上一层ntp主机地址
st - stratum阶层
when - 多少秒前曾经同步过时间
poll - 下次更新在多少秒后
reach - 已经向上层ntp服务器要求更新的次数
delay - 网络延迟
offset - 时间补偿
jitter - 系统时间与bios时间差
要查看 ntpd 进程的状态,请运行以下命令,按 Ctrl+C 停止查看进程。
第一列中的字符指示源的质量。星号 ( * ) 表示该源是当前引用。
remote 列出源的 IP 地址或主机名。
when 指出从轮询源开始已过去的时间(秒)。
poll 指出轮询间隔时间。该值会根据本地时钟的精度相应增加。
reach 是一个八进制数字,指出源的可存取性。值 377 表示源已应答了前八个连续轮询。
下面是网上关于ntpd与ntpdate区别的相关资料。如下所示所示:
使用之前得弄清楚一个问题,ntpd与ntpdate在更新时间时有什么区别。ntpd不仅仅是时间同步服务器,它还可以做客户端与标准时间服务器进行同步时间,而且是平滑同步,并非ntpdate立即同步,在生产环境中慎用ntpdate,也正如此两者不可同时运行。
时钟的跃变,对于某些程序会导致很严重的问题。许多应用程序依赖连续的时钟——毕竟,这是一项常见的假定,即,取得的时间是线性的,一些操作,例如数据库事务,通常会地依赖这样的事实:时间不会往回跳跃。不幸的是,ntpdate调整时间的方式就是我们所说的”跃变“:在获得一个时间之后,ntpdate使用settimeofday(2)设置系统时间,这有几个非常明显的问题:
第一,这样做不安全。ntpdate的设置依赖于ntp服务器的安全性,攻击者可以利用一些软件设计上的缺陷,拿下ntp服务器并令与其同步的服务器执行某些消耗性的任务。由于ntpdate采用的方式是跳变,跟随它的服务器无法知道是否发生了异常(时间不一样的时候,唯一的办法是以服务器为准)。
第二,这样做不精确。一旦ntp服务器宕机,跟随它的服务器也就会无法同步时间。与此不同,ntpd不仅能够校准计算机的时间,而且能够校准计算机的时钟。
第三,这样做不够优雅。由于是跳变,而不是使时间变快或变慢,依赖时序的程序会出错(例如,如果ntpdate发现你的时间快了,则可能会经历两个相同的时刻,对某些应用而言,这是致命的)。因而,唯一一个可以令时间发生跳变的点,是计算机刚刚启动,但还没有启动很多服务的那个时候。其余的时候,理想的做法是使用ntpd来校准时钟,而不是调整计算机时钟上的时间。
NTPD 在和时间服务器的同步过程中,会把 BIOS 计时器的振荡频率偏差——或者说 Local Clock 的自然漂移(drift)——记录下来。这样即使网络有问题,本机仍然能维持一个相当精确的走时。
参考资料:http://www.cnblogs.com/kerrycode/archive/2015/08/20/4744804.html