检测不到手机忙音

3825+CME+E1 进入30B+D 别的通话功能都没问题 也能检测到小灵通 固话的忙音 但是当从内线打外线的手机 如果手机拒接了 直接挂断 在内线的电话上听不到忙音 还是正常呼叫的那种长嘟声 在3825上DUBUG信息 正常手机接通后挂断的信息 *Mar 26 07:55:03.643: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 65846819 *Mar 26 07:55:03.643: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 13810439306 *Mar 26 07:55:03.643: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8  callref = 0x0085         Sending Complete         Bearer Capability i = 0x8090A3                 Standard = CCITT                 Transfer Capability = Speech                   Transfer Mode = Circuit                 Transfer Rate = 64 kbit/s         Channel ID i = 0xA9839F                 Exclusive, Channel 31         Progress Ind i = 0x8183 - Origination address is non-ISDN           Calling Party Number i = 0x0180, '65846819'                 Plan:ISDN, Type:Unknown         Called Party Number i = 0x81, '13810439306'                 Plan:ISDN, Type:Unknown *Mar 26 07:55:03.671: ISDN Se0/2/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x8085         Channel ID i = 0xA9839F                 Exclusive, Channel 31 *Mar 26 07:55:09.563: ISDN Se0/2/0:15 Q931: RX <- ALERTING pd = 8  callref = 0x8085 *Mar 26 07:55:22.099: ISDN Se0/2/0:15 Q931: RX <- CONNECT pd = 8  callref = 0x8085         Date/Time i = 0x08031A0F36 *Mar 26 07:55:22.099: %ISDN-6-CONNECT: Interface Serial0/2/0:30 is now connected to 13810439306 N/A *Mar 26 07:55:22.103: ISDN Se0/2/0:15 Q931: TX -> CONNECT_ACK pd = 8  callref = 0x0085 *Mar 26 07:55:27.195: ISDN Se0/2/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x8085         Cause i = 0x8090 - Normal call clearing         Progress Ind i = 0x8288 - In-band info or appropriate now available *Mar 26 07:55:27.195: %ISDN-6-DISCONNECT: Interface Serial0/2/0:30  disconnected from 13810439306 , call lasted 5 seconds *Mar 26 07:55:27.195: ISDN Se0/2/0:15 Q931: call_disc: PI received in disconnect; Postpone sending RELEASE for callid 0x8006 手机不接 直接挂断的信息 *Mar 26 07:56:48.359: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 65846819 *Mar 26 07:56:48.359: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 13810439306 *Mar 26 07:56:48.359: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8  callref = 0x0087         Sending Complete         Bearer Capability i = 0x8090A3                 Standard = CCITT                 Transfer Capability = Speech                   Transfer Mode = Circuit                 Transfer Rate = 64 kbit/s         Channel ID i = 0xA9839E                 Exclusive, Channel 30         Progress Ind i = 0x8183 - Origination address is non-ISDN           Calling Party Number i = 0x0180, '65846819'                 Plan:ISDN, Type:Unknown         Called Party Number i = 0x81, '13810439306'                 Plan:ISDN, Type:Unknown *Mar 26 07:56:48.391: ISDN Se0/2/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x8087         Channel ID i = 0xA9839E                 Exclusive, Channel 30 *Mar 26 07:56:51.891: ISDN Se0/2/0:15 Q931: RX <- ALERTING pd = 8  callref = 0x8087   相关的E1的配置 isdn switch-type primary-net5 controller E1 0/2/0 clock source internal pri-group timeslots 1-31 description to pstn interface Serial0/2/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn overlap-receiving T302 3000 isdn incoming-voice voice isdn sending-complete no cdp enable voice-port 0/2/0:15 cptone CN timeouts interdigit 3 timeouts call-disconnect 2 timeouts wait-release 1 dial-peer voice 1 pots translation-profile outgoing outsideBJ preference 7 destination-pattern 9.T direct-inward-dial port 0/2/0:15 在UC群里的沁园春.雪的帮助下 找到如下解决方案 输入下列命令 问题解决了 dial-peer voice 1 pots progress_ind setup enable 3 progress_ind alert enable 8