移植U-Boot-2008.10到友善之臂mini2440（六）

 

1.2.12 修改u-boot-2008.10/include/configs/mini2440.h 头文件

---

 

 

(1)添加对2440的宏定义：

#define CONFIG_ARM920T         1       /* This is an ARM920T Core     */

#define CONFIG_S3C2440         1 /* in a SAMSUNG S3C2440 SoC */

#define CONFIG_mini2440           1 /* on a SAMSUNG mini2440 Board */

#define CONFIG_mini2440_LED      1 /* Use the LED on Board */

//#define      CONFIG_S3C2410  1   /* in a SAMSUNG S3C2410 SoC     */

//#define CONFIG_SMDK2410       1  /* on a SAMSUNG SMDK2410 Board  */

/* input clock of PLL */

 

(2)修改网卡的宏定义，注释掉CS8900的部分，添加对DM9000的支持：

/*

 * Hardware drivers

 */

//#define CONFIG_DRIVER_CS8900 1       /* we have a CS8900 on-board */

//#define CS8900_BASE          0x19000300

//#define CS8900_BUS16         1 /* the Linux driver does accesses as shorts */

 

#define CONFIG_DRIVER_DM9000          1

#define CONFIG_DM9000_USE_16BIT               1

#define CONFIG_DM9000_BASE                    0x20000300

#define DM9000_IO                             0x20000300 

#define DM9000_DATA                           0x20000304

 

(3)添加支持Nand 启动等宏定义，将相关IP设置的注释去掉，并修改IP设置，顺便修改下启动参数的宏设置：

#define CONFIG_CMD_CACHE

#define CONFIG_CMD_DATE

#define CONFIG_CMD_ELF

 

#define CONFIG_CMD_PING

 

#define CONFIG_SETUP_MEMORY_TAGS

#define CONFIG_INITRD_TAG

#define CONFIG_CMDLINE_TAG

/*向linux内核传递函数所需的宏*/

 

//nand Flash param

 

#define CONFIG_CMD_NAND

 

#define CONFIG_CMDLINE_EDITING

 

#ifdef CONFIG_CMDLINE_EDITING

#undef CONFIG_AUTO_COMPLETE

#else

#define CONFIG_AUTO_COMPLETE

#endif

 

//#define CONFIG_NAND_LEGACY

//不使用LEGACY,以使用自带的nand flash驱动

/*

 * NAND flash settings

 */

#if defined(CONFIG_CMD_NAND)

#define CFG_NAND_BASE 0x4E000000

/* NandFlash控制器在SFR区起始寄存器地址 */

#define CFG_MAX_NAND_DEVICE    1      

/* Max number of NAND devices         */

 

#define CONFIG_MTD_NAND_VERIFY_WRITE 1 //使能flash写校验

 

 

/* #undef CONFIG_MTD_NAND_VERIFY_WRITE */

#endif  /* CONFIG_CMD_NAND */

 

#define CONFIG_BOOTDELAY       2

#define CONFIG_BOOTARGS        "noinitrd root=/dev/nfs nfsroot=192.168.1.10:/opt/root_nfs ip=192.168.1.70:192.168.1.10:192.168.1.10:255.255.255.0:mini.arm9.net:eth0:off init=linuxrc console=ttySAC0"

#define CONFIG_ETHADDR 08:00:3e:26:0a:5b 

#define CONFIG_NETMASK             255.255.255.0

#define CONFIG_IPADDR          192.168.1.70    /*改变默认的IP地址*/

#define CONFIG_SERVERIP        192.168.1.80  /*改变原服务器IP地址*/

/*#define CONFIG_BOOTFILE      "elinos-lart" */

#define CONFIG_BOOTCOMMAND     "tftp 0x31000000 uImage;bootm 0x31000000"

……

#undef  CFG_CLKS_IN_HZ         /* everything, incl board info, in Hz */

 

#define CFG_LOAD_ADDR  0x31000000     /* default load address        bootm use it*/

......

/*------------------------------------------------------------------

 * FLASH and environment organization

 */

//#define CONFIG_AMD_LV400     1       /* uncomment this if you have a LV400 flash */

//#if 0

//#define CONFIG_AMD_LV800     1       /* uncomment this if you have a LV800 flash */

//#endif

#define CONFIG_AMD_LV800              /*mini2440上用的是2M的Nor Flash，暂时用这个也可以从Nor Flash启动 */

/*------------------------------*/

 

(5)在Nand Flash中保存 u-boot 参数 (saveenv 功能)：

/* timeout values are in ticks */

#define CFG_FLASH_ERASE_TOUT   (5*CFG_HZ) /* Timeout for Flash Erase */

#define CFG_FLASH_WRITE_TOUT   (5*CFG_HZ) /* Timeout for Flash Write */

 

#define CONFIG_ENV_IS_IN_NAND   1

#define CONFIG_ENV_OFFSET       0x30000

//#define CFG_ENV_OFFSET 0X30000

//#define      CONFIG_ENV_IS_IN_FLASH 1

#define CONFIG_ENV_SIZE     0x10000   /* Total Size of Environment Sector */

 

(6)为了在U-Boot运行阶段对一些寄存器进行操作，在此文件后面添加代码：

# if defined(CONFIG_mini2440_LED)

/* GPIO */

#define GPIO_CTL_BASE 0x56000000

#define oGPIO_B 0x10

#define oGPIO_CON 0x0 /* R/W, Configures the pins of the port */

#define oGPIO_DAT 0x4 /* R/W, Data register for port */

#define oGPIO_UP 0x8 /* R/W, Pull-up disable register */

 

#endif

 

#define STACK_BASE 0x33f00000

#define STACK_SIZE 0x8000

 

/* NAND Flash Controller */

#define NAND_CTL_BASE 0x4E000000

#define bINT_CTL(Nb) __REG(INT_CTL_BASE + (Nb))

/* Offset */

#define oNFCONF 0x00

 

# if defined(CONFIG_S3C2440)

#define CONFIG_S3C2440_NAND_BOOT 1

/* Offset */

#define oNFCONT 0x04

#define oNFCMD 0x08

#define oNFADDR 0x0c

#define oNFDATA 0x10

#define oNFSTAT 0x20

#define oNFECC 0x2c

#define rNFCONF (*(volatile unsigned int *)0x4e000000)

#define rNFCONT (*(volatile unsigned int *)0x4e000004)

#define rNFCMD (*(volatile unsigned char *)0x4e000008)

#define rNFADDR (*(volatile unsigned char *)0x4e00000c)

#define rNFDATA (*(volatile unsigned char *)0x4e000010)

#define rNFSTAT (*(volatile unsigned int *)0x4e000020)

#define rNFECC (*(volatile unsigned int *)0x4e00002c)

#endif

 

# if defined(CONFIG_S3C2410)

#define CONFIG_S3C2410_NAND_BOOT 1

/* Offset */

#define oNFCONF 0x00

#define oNFCMD 0x04

#define oNFADDR 0x08

#define oNFDATA 0x0c

#define oNFSTAT 0x10

#define oNFECC 0x14

#define rNFCONF (*(volatile unsigned int *)0x4e000000)

#define rNFCMD (*(volatile unsigned char *)0x4e000004)

#define rNFADDR (*(volatile unsigned char *)0x4e000008)

#define rNFDATA (*(volatile unsigned char *)0x4e00000c)

#define rNFSTAT (*(volatile unsigned int *)0x4e000010)

#define rNFECC (*(volatile unsigned int *)0x4e000014)

#define rNFECC0 (*(volatile unsigned char *)0x4e000014)

#define rNFECC1 (*(volatile unsigned char *)0x4e000015)

#define rNFECC2 (*(volatile unsigned char *)0x4e000016)

#endif

#endif  /* __CONFIG_H */

 

---

1.2.13 修改u-boot-2008.10/lib_arm/board.c 文件

---

(1)添加头文件引用：

#include <nand.h>

#include <onenand_uboot.h>

#include <s3c2410.h>

 

(2)添加LED功能，指示进度：
static int display_banner (void)

 {

# if defined(CONFIG_mini2440_LED)    

    S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();

         gpio->GPBDAT = 0x100;

 

//在串口初始化和console初始化完成，串口输出信息之前，LED1、LED2、LED3会亮起！

 

#endif

 

#if !defined(CONFIG_mini2440_LED)

        S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();

 

#endif

 

        printf ("\n\n%s\n\n", version_string);

 

……

        reset_phy();

 #endif

 #endif

 

#if defined(CONFIG_mini2440_LED)     

               S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();

#endif

 

# if defined(CONFIG_mini2440_LED)    

         gpio->GPBDAT = 0x0;

 

//在进入命令提示符之前，四个LED会同时亮起！

 

#endif

        /* main_loop() can return to retry autoboot, if so just run it again. */